Table of Contents
Advertisement
Quick Links
Hitachi Plasma Display Tilting Wall-mount Unit
Model
CMPAK06
Thank you for purchasing the Hitachi Plasma Display Wall-mount Unit.
To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual
in a safe place for future reference.
This plasma display wall-mount unit is for use only with the following model:
CMP5000WX
Special techniques are necessary for installation of the plasma display.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
This company assumes absolutely no responsibility for injuries and damages that may occur due to improper
installation and handling.
Please remember that if you remove the plasma display set from the wall later, you will find the screw holes
and anchor bolts for the mounting unit left on the wall. Also note that a long use of the plasma display set
may discolor the wall around it due to its heat and air flow.
To dealers and shops
To ensure customer safety, be sure to design the installation location so that the strength is sufficient to
withstand the weight of both the plasma display and the wall-mount unit.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Parts Configuration Chart
IConfirming the parts provided
Before assembly,
check to make sure that none of the parts provided are missing.
* Screws to be used for wall installation are not included. Obtain them separately.
Hung on wall unit (1)
Installation Instructions
Bolts M8 (6)
Hexagon wrench (1)
Advertisement
Table of Contents
Related Manuals for Hitachi CMPAK06
Summary of Contents for Hitachi CMPAK06
-
Page 1: Installation Instructions
Model CMPAK06 Installation Instructions Thank you for purchasing the Hitachi Plasma Display Wall-mount Unit. To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual in a safe place for future reference. This plasma display wall-mount unit is for use only with the following model: CMP5000WX Special techniques are necessary for installation of the plasma display. -
Page 2: Safety Cautions
Usage cautions to ensure correct usage Symbols The following symbols are used to ensure safe usage of the product, to prevent danger to yourself and other parties and to prevent damage to property. This symbol indicates that incorrect handling due to ignoring this symbol WARNING can result in the possibility of personal injury or even death. -
Page 3: Installation Location
Installation Location WARNING The wall where the wall-mount unit is to be Plaster board or thin ply wood, etc. installed must be capable of long-term support of the total load of the plasma display and wall-mount unit. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. - Page 4 CAUTION Do not install in Do not install where locations where there is direct there is excessive sunlight and other vibration or impact. strong light. Injury and damage Strong light could result could result from in eye fatigue during falling. usage.
-
Page 5: Installation Method
Installation Method Installation procedure Be sure to install the speaker at this stage. Remove the special screws (2 locations) from the For the installation method, refer to the speaker installation bottom of the hung on wall unit. procedure in the speaker user manual. Attach the wall side hardware to the wall. -
Page 6: Angle Setup
Installation Method Angle setup This installation hardware allows the display to be directed downwards freely at any angle from the vertical to 25ˇ. This adjustment must always be done by 2 people. Adjust the angle by rotating the screws at the center top and center bottom of the wall side hardware to the left or right. If the angle is increased while you are adjusting the angle using the screw at the center of the bottom, it is difficult to turn the screw. -
Page 7: Product Specifications
Product Specifications External Dimensions (258) (143) (314) (314) (239) 6-23x10.5 6-φ10.5 1218 (Without side speaker) 1368 (With side speaker) Mass 13.8kg Main material Steel sheet Surface treatment Black baked paint Products mounted CMP5000WX... - Page 8 Hitachi, Ltd. Tokyo Japan 292 Yohida-cho, Totsuka-ku, Yokohama, Digital Media Division (045) 866-6302 244-0817 Japan...