Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG 115 D
Summary of Contents for AEG 115 D
- Page 1 115 D Extractor Hood Installation and Operating Instructions...
-
Page 2: Table Of Contents
Contents Introduction Extractor version Recirculating mode Electrical connections Safety warnings for electrician Specifications Installation Safety warnings for kitchen unit installer Wall unit mounting Wall mounting Hood operation Safety warnings for user Maintenance and care Opening the grille Grease filter carbon filter Changing the light bulb Cleaning Special Accessories... -
Page 3: Introduction
Introduction The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). Extractor The unit features two outlet holes, one of which A is located on the version top of the unit while the other B is located on the rear. -
Page 4: Recirculating Mode
The air is filtered and recirculated through the front grille. Move the handle F to position F — Fig. 3. You will need an original AEG KLF60/80 activated carbon filter for the recirculating mode. (See special accessories). Summer/winter operation changeover To avoid unnecessary outdoor transport of thermal energy during exhaust air operation in winter, we reccommend you to convert the fume extractor hood to winter operation (return air). -
Page 5: Electrical Connections
Electrical connections Voltage and Please ensure that the voltage and current indicated on the rating current plate agree with the voltage of your electricity supply. If your appliance has been equipped with a mains lead with a moulded-on type plug, you must comply with the following regulations: The plug moulded on to the lead incorporates a fuse. - Page 6 Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a quali- fied electrician who is a member of the NICEIC who will comply with the IEE and any local regulations.
- Page 7 Appliances Your appliance must be connected to fixed wiring via the use of with 3 wires a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a quali- fied electrician who is a member of the NICEIC who will comply with the IEE and any local regulations.
-
Page 8: Specifications
Specifications Dimensions: Height Weight: Net: 8.7 Kg Gross: 9.6 Kg Length of the cable: 140 cm Maximum absorbed power: 230 W Motor absorption: 1 x 150 W Lighting: Fan powers (levels), levels in compliance with DIN 44971 Level: Min. Extractor: 116 m Filter: 60 m Extractor system: 100 and 120 mm Ø... -
Page 9: Installation
Installation Safety When used as an extractor unit, the hood must be fitted with a 100 warnings for or 120 mm diameter hose. kitchen unit If the outlet hose is installed in a horizontal position, it must be installer slanted at an angle of 10° so that the air can flow outside without impediment. -
Page 10: Wall Unit Mounting
Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm , which is to say a larger hole, could reduce the performance of the extractor hood. If the hood is used in its recirculating mode, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures. -
Page 11: Wall Mounting
Wall — Position the template on the wall. mounting — Drill four 8 mm Ø holes in the wall, 2 in points H and 2 in points — Fit the four 8 mm screw anchor plugs in the wall. — Screw two 5 x 45 mm screws in points H but do not tighten them fully home. -
Page 12: Hood Operation
Hood Operation The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. -
Page 13: Maintenance And Care
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening — Open the latch L and swing the grille downwards. — Fig. 7. the grille — To remove the grille, pull it forwards from the right and release it. The metal grease filter has been designed to absorb the grease Grease filter particles that are formed during cooking and is always used,... -
Page 14: Changing The Light Bulb
Removing the filter — Press the stops N and remove the filter by pulling it down- wards. — Fig. 8 Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. The activated carbon filter can be ordered from AEG service. -
Page 15: Cleaning
Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grille. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. -
Page 16: Technical Assistance Service
Technical assistance service In case of any enquiries and faults, please call AEG After-Sales Service: AEG Domestic Appliances Limited Head Office: 217 Bath Road Slough, Berks SL1 4AW Tel: 01753 872506 Telefax: 01753 512271 AEG Northern Service Centre: Unit 20, Haigh Park Haigh Avenue Stockport GL Manchester SK4 1QR... - Page 17 If your appliance has a fault, please contact our service engineer and state the following numbers: E-Nr. 610 F-Nr. AEG Hausgeräte AG Postfach 1036 D-90327 Nürnberg © Copyright by AEG L 489B Ed. 05/95 H 260 287 140 159/95...