Honeywell WAVE2EX - Ademco Two Tone Siren Installation And Setup Manual page 22

LYNXR-I Installation and Setup Guide
Data Field Descriptions
All four digits of the Subscriber Account number must be entered in Fields ✻ 43 and ✻ 44. If ten-digit format is selected
in ✻ 48 (option 5), all ten digits of the Subscriber Account number must be entered.
✻ ✻
Fields 43 and 44:
✻
Enter [ ] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first
digit of a 4-digit account number for Nos. 0000–0999. Enter [
CID®) is used. Exit field by pressing [
blank Programming Form for examples of account number entries. If using the paging feature, do not enter a leading 0
in the subscriber account number, and do not use digits A-F anywhere in the number. Some paging systems provide
voice mail capability, which is activated by a leading 0 in the message. Enter digits 0–9; # +11=B; # +12=C; # +13=D; #
+14=E; or # +15=F.
✻ Primary Subs Account No.
43
Enter a four or ten digit account number.
Secondary Subs Account No.
✻
44
Enter a four or ten digit account number.
Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for '*'; #+12 for'#'; #+13 for a pause (2 seconds).
"Follow Me Reminder" Phone Number
✻
46
Enter up to 24 digits.
✻ Phone System Select
47
Central
Station Pulse
No WATS 0 = No
Speaker
Phone
WATS 2 = No
Speaker
Phone
✻ Report Format for Primary/Secondary
48
Primary
See choices below
0 = 3+1; 4+1 ADEMCO Low Speed Standard
1 = 3+1; 4+1 Radionics Standard
2 = 4+2 ADEMCO Low Speed Standard
3 = 4+2 Radionics Standard
5 = ADEMCO Contact ID® Reporting with 10-digit
subscriber account number
6 = 4+2 ADEMCO Express
7 = ADEMCO Contact ID® Reporting with 4-digit
subscriber account number
8 = 3+1; 4+1 ADEMCO Low Speed Expanded
9 = 3+1; 4+1 Radionics Expanded
✻
] if only 3 digits are used. To clear entries from field, press
Dialing Mode
Tone Pulse Tone
1 = No 4 = With 5 = With
Speaker Speaker Speaker
Phone Phone Phone
3 = No 6 = With 7 = With
Speaker Speaker Speaker
Phone Phone Phone
Secondary
See choices below
✻
] as the fifth digit if a 4-digit account number (for 3+1,
Enter the primary subscriber account number.
To clear entries from field, press ✻ 43 ✻ .
Enter the secondary subscriber account number.
To clear entries from field, press ✻ 44 ✻ .
This option allows the user to schedule a time driven message.
When activated the system will dial the phone number
programmed and deliver a voice message (custom words 72, 73
and 74). This option is only supported when the pager or follow
me feature is enabled in field ✻ 49 (option 6-9 or 10-13).
If using the Follow Me Reminder feature, enter the phone number
here. If fewer than 24 digits are entered, exit by pressing [ ✻ ]. To
clear entries from the field press ✻ 46 ✻ .
The telephone message can be terminated (acknowledged) by
pressing any key on the telephone keypad. Pressing any key on
the local LYNXR-I keypad will terminate (acknowledge) both the
follow me and the local reminder announcements.
Note: The follow me reminder announcement will be terminated if
any other event requires the system to dial out or if an
audible alarm has occurred.
This option is used to enter the correct type of phone dialing
(pulse or tone), and to select the correct WATS line option for the
Central Station. This option is used to activate the Speaker Phone
option.
Note: If using pulse dialing, you must enter the numbers slowly in
order to allow the pulse dialer time to operate.
Enter ✻ as the 4th digit of ✻ 43 through ✻ 44, if 3+1 dialer
reporting is to be used. (For an explanation of these formats, see
the System Communication section of this manual.)
Notes: (1) The maximum number of alarm and alarm restore
reports during one armed period is determined by field
✻ 92.
(2) If Option 5 is selected a 10-digit account number must
be entered in Fields ✻ 43 or ✻ 44.
(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must
be selected for AVM.
- 22 -
✻ ✻ ✻ ✻
or
43 44 . See