Fujitsu MAP3147NC - Enterprise - Hard Drive Product/Maintenance Manual
Disk drives
Hide thumbs
Also See for MAP3147NC - Enterprise - Hard Drive:
- Scsi logical interface specifications (290 pages) ,
- Installation manual (2 pages) ,
- Installation manual (2 pages)
Related Manuals for Fujitsu MAP3147NC - Enterprise - Hard Drive
Summary of Contents for Fujitsu MAP3147NC - Enterprise - Hard Drive
- Page 1 C141-E166-01EN MAP3147NC/NP MAP3735NC/NP MAP3367NC/NP DISK DRIVES PRODUCT/MAINTENANCE MANUAL...
- Page 2 FOR SAFE OPERATION Handling of This manual IMPORTANT NOTE TO USERS READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT. INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO USERS, BYSTANDERS OR PROPERTY.
- Page 3 REVISION RECORD Edition Date published Revised contents May, 2002 Specification No.: C141-E166-**EN...
- Page 4 Related Standards...
- Page 5 PREFACE OVERVIEW OF MANUAL Chapter 1 GENERAL DESCRIPTION Chapter 2 SPECIFICATIONS Chapter 3 DATA FORMAT Chapter 4 INSTALLATION REQUIREMENTS Chapter 5 INSTALLATION Chapter 6 DIAGNOSIS and MAINTENANCE Chapter 7 ERROR ANALYSIS APPENDIX A to B...
-
Page 7: Important Alert Items
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation result in if the user does not perform the procedure correctly. This alert signal also indicates that damages to the product or other property occur if the user does not perform the procedure correctly. - Page 8 Task Alert message Page Mounting Installation 5-11 6-15 C141-E166...
- Page 11 CONTENTS CHAPTER 1 GENERAL DESCRIPTION ................1-1 CHAPTER 2 SPECIFICATIONS...................2-1 CHAPTER 3 DATA FORMAT....................3-1 CHAPTER 4 INSTALLATION REQUIREMENTS .............4-1...
- Page 12 CHAPTER 5 INSTALLATION....................5-1 CHAPTER 6 DIAGNOSTICS AND MAINTENANCE ............6-1...
- Page 13 CHAPTER 7 ERROR ANALYSIS ..................7-1 APPENDIX A SETTING TERMINALS ..................A-1 APPENDIX B CONNECTOR SIGNAL ALLOCATION ............B-1 INDEX ..........................IN-1...
- Page 14 This page is intentionally left blank.
- Page 15 FIGURES...
- Page 17 TABLES...
- Page 18 This page is intentionally left blank.
- Page 19 CHAPTER 1 GENERAL DESCRIPTION Standard Features Hardware Structure System Configuration...
- Page 20 Standard Features...
- Page 21 Note: CAUTION...
- Page 22 CAUTION...
- Page 24 Hardware Structure Figure 1.1 NC model drives outer view Figure 1.2 NP model drives outer view...
- Page 25 Figure 1.3 Disk/head configuration...
- Page 27 System Configuration Figure 1.4 System configuration...
-
Page 29: Specifications
CHAPTER 2 SPECIFICATIONS Hardware Specifications SCSI Function Specifications Hardware Specifications 2.1.1 Model name and order number Table 2.1 Model names and order numbers... - Page 30 2.1.2 Function specifications Table 2.2 Function specifications...
- Page 32 2.1.3 Environmental specifications Table 2.3 Environmental/power requirements...
- Page 33 2.1.4 Error rate CAUTION 2.1.5 Reliability Note:...
- Page 34 Note:...
- Page 35 SCSI Function Specifications Table 2.4 SCSI function specifications N P model)
- Page 36 This page is intentionally left blank.
- Page 38 Figure 3.1 Cylinder configuration...
- Page 39 Table 3.1 Zone layout and track capacity...
- Page 52 Automatic alternate block allocation is made only once during the execution of one command. If second defective block is detected, the alternate block assignment processing for the first defective block is executed but the alternate block assignment processing for the second one is not executed and the command being executed terminates.
- Page 54 The value marked with (*) indicates the dimension between mounting holes on the bottom face. Figure 4.1 NC external dimensions C141-E166...
- Page 67 Figure 4.18 16-bit SCSI ID external input...
- Page 68 IMPORTANT IMPORTANT...
- Page 69 Figure 4.19 Output signal for external LED...
- Page 70 Cable connection requirements The requirements for cable connection between the IDD, host system, and power supply unit are given in Figure 4.20. Recommended components for connection are listed in Table 4.2. External operator panel (example) Figure 4.20 SCSI cables connection 4-18 C141-E166...
- Page 73 Table 4.2 Recommended components for connection...
-
Page 75: Chapter 5 Installation
CHAPTER 5 INSTALLATION Notes on Handling Drives Connections Setting Terminals Mounting Drives Connecting Cables Confirming Operations after Installation and Preparation for Use Dismounting Drives Spare Disk Drive Notes on Handling Drives CAUTION Hot temperature To prevent injury, do not handle the drive until after the device has cooled sufficiently after turning off the power. - Page 79 Setting Terminals A user sets up the following terminals and SCSI terminating resistor before installing the IDD in the system as required. Setting terminal: CN2 (NP model only) Figures 5.2 shows the location of setting terminal. Figures 5.3 shows the allocation and default settings.
- Page 84 Mounting Drives 5.4.1 Check before mounting Table 5.8 Setting check list (NP model only) ¤ ¤ ¤ ¤ ¤ ¤ ¤ ¤ ¤ ¤ ¤ 5.4.2 Mounting procedures...
- Page 94 Notes: Notes:...
- Page 105 ¡...
-
Page 113: Chapter 7 Error Analysis
CHAPTER 7 ERROR ANALYSIS Error Analysis Information Collection Sense Data Analysis Error Analysis Information Collection 7.1.1 Sense data 7.1.2 Sense key, sense code, and subsense code... -
Page 117: Appendix Asetting Terminals
APPENDIX A SETTING TERMINALS Setting Terminals (on NP model only) - Page 118 Setting Terminals (on NP model only) Table A.1 CN2 setting terminal (on NP model drives only) Note:...
-
Page 119: Appendix Bconnector Signal Allocation
APPENDIX B CONNECTOR SIGNAL ALLOCATION SCSI Connector Signal Allocation: 68 pin type LVD 16-bit SCSI SCSI Connector Signal Allocation: SCA2 type LVD 16-bit SCSI... - Page 120 SCSI Connector Signal Allocation: 68 pin type LVD 16-bit SCSI Table B.1 SCSI connector (68 pin type LVD 16-bit SCSI): CN1...
- Page 121 SCSI Connector Signal Allocation: SCA2 type LVD 16-bit SCSI Table B.2 SCSI connector (SCA2 type LVD 16-bit SCSI): CN1...
- Page 122 This page is intentionally left blank.
-
Page 123: Index
INDEX +12 VDC ............4-8 1-1x-xx ............7-4 16-bit SCSI ID external input......4-15 cache feature............1-3 16-bit SCSI interface connector ....4-12 caching parameter .........5-21 3-0C-03 ............7-4 changing revision number in field....6-9 3-1x-xx ............7-4 check before mounting ........5-10 4-40-xx ............7-4 check items at illegal operation .....5-12 4-44-xx ............7-4 checking at abnormal end......5-16 4-C4-xx ............7-4... - Page 124 internal test space ..........3-4 E-1D-00............7-4 each mode setting ..........5-7 ECC ..............3-8 large capacity ..........1-5 environmental specification ......2-4 leak magnetic flux ...........4-7 environmental temperature......4-6 limitation of bottom-mounting ......4-5 environmental/power requirement ....2-4 limitation of side-mounting ......4-5 error analysis ...........7-1 logical data block addressing ......3-9 error analysis information collection....7-1 low noise and low vibration ......1-5 error information indicated with sense data ..7-3...
- Page 125 parts that can be replaced in field....6-7 setting of SCSI interface physical sector allocation ........3-5 operation mode ........5-8, 5-9 PLO Sync ............3-8 setting parameter ...........5-18 positioning error rate ........2-5 setting SCSI terminator power supply.....5-7 power on/off sequence ........4-9 setting terminal........5-5, A-1 power supply connector ........4-12 setting terminal (on NP model only) ....A-2 power supply requirement.......4-8...
- Page 126 This page is intentionally left blank.
- Page 127 211-8588, Japan FAX: 34-91-581-8300 TEL: 81-44-754-2130 FAX: 81-44-754-8346 FUJITSU AUSTRALIA LIMITED 2 Julius Avenue (Cnr Delhi Road) North Ryde N.S.W. 2113, FUJITSU COMPUTER PRODUCTS OF AMERICA, INC. AUSTRALIA 2904 Orchard Parkway, San Jose, TEL: 61-2-9776-4555 California 95134-2009, U.S.A. FAX: 61-2-9776-4556 TEL:...
- Page 128 This page is intentionally left blank.
- Page 129 FUJITSU LIMITED Reader Comment Form We would appreciate your comments and suggestions for improving this publication. Publication No. Rev. Letter Title Current Date How did you use this publication? Is the material presented effectively? Learning Sales Installing Fully Well Well...
- Page 130 This page is intentionally left blank.