JVC DT-V24L3DU - 24IN DTV LCD MONITOR Instructions Manual

JVC DT-V24L3DU - 24IN DTV LCD MONITOR Instructions Manual

Multi format lcd monitor

Advertisement

DT-V24L3D
DT-V20L3D
MULTI FORMAT LCD MONITOR
The illustration of the monitor is of DT-V24L3D.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do
not remove cover (or back). No user
serviceable parts inside. Refer servicing
to qualified service personnel.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
INSTRUCTIONS

Table of Contents

Safety Precautions .............................................. 2
IMPORTANT SAFEGUARDS ........................... 2
Installation ............................................................ 4
Daily Operations / Connections ......................... 6
Front panel ....................................................... 6
Rear panel ........................................................ 8
Available signals ............................................... 9
Menu Configuration-MAIN MENU .................. 10
External Control ................................................. 16
About the external control .............................. 16
Using the serial communication ..................... 18
Troubleshooting ................................................. 19
Self-check program ........................................ 20
Maintenance ....................................................... 20
Specifications .................................................... 21
General ........................................................... 21
Input/output terminals ..................................... 21
Dimensions ..................................................... 22
LCT2447-002A-H

Advertisement

Table of Contents
loading

Summary of Contents for JVC DT-V24L3DU - 24IN DTV LCD MONITOR

  • Page 1: Table Of Contents

    The lightning flash with arrowhead symbol, within an equilateral triangle is CAUTION intended to alert the user to the presence of uninsulated “dangerous voltage” RISK OF ELECTRICAL SHOCK within the product’s enclosure that may DO NOT OPEN be of sufficient magnitude to constitute a risk of electric shock to persons.
  • Page 2: Safety Precautions

    Safety Precautions WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO Under the following conditions, Do not use the product for a long time if the sound RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 1.
  • Page 3: Important Safety Instructions

    European Union only FCC NOTICE Dear Customer, EMC Supplement CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the This apparatus is in conformance with the valid This equipment is in conformity with the provisions equipment.
  • Page 4: Installation

    Installation CAUTION To detach the stand • Do not rest your arm on the monitor or lean against the monitor. CAUTION • Do not touch the LCD panel when installing the monitor. Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged. •...
  • Page 5 To adjust the stand height To prevent an accidental fall To change the stand height, detach the stand from the monitor (☞ “To detach the stand” on page 4). Then, Fix the monitor to a wall by using strings. change the position of the stand plate according to the stand height you want by choosing the screw holes to use. Fixing the monitor Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper side) using M4 x 10 mm screws (not provided).
  • Page 6: Daily Operations / Connections

    Daily Operations / Connections 7 Front panel • “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work). Tally lamp •...
  • Page 7 Menu Operations Audio Channel Selection On the Information Display On the Status Display Select audio channels emitted from the speakers The monitor displays the information below. If you press the INPUT SELECT button of the Display the menu. (L/R) and the AUDIO ASSIGN (MONITOR OUT) •...
  • Page 8: Rear Panel

    Daily Operations / Connections (cont.) 7 Rear panel 8 AUDIO ASSIGN (MONITOR OUT) terminals Note for connections (pin jack) • Before making any connections, turn off all the Output terminals for the analog audio signal. equipment. • The terminals output the audio signal through •...
  • Page 9: Available Signals

    7 Available signals Computer signals (preset) DVI-D (HDCP) terminals The following signals are available for this monitor. Resolution Frequency Video signals Signal name Scan system Horizontal Vertical Horizontal (kHz) Vertical (Hz) Input terminal VGA60 31.5 59.9 Non-interlace Signal format COMPO./RGB shown in the VIDEO E.
  • Page 10: Menu Configuration-Main Menu

    Menu Configuration—MAIN MENU For the operation procedure, see page 7. PICTURE FUNCTION Setting for the picture quality Item To do Setting value MOVING Reduce the lag of moving pictures which is peculiar to LCD. OFF, ON PICTURE* APERTURE Select the frequency of the luminance signal compensated in OFF, LOW, HIGH FREQ.* “APERTURE LEVEL.”...
  • Page 11 MARKER* Settings for marker functions Item To do Setting value ☞ “NOTE” AREA MARKER* Activate/deactivate the area marker and select the style of it. MARKER ASPECT* Select the aspect ratio of the area marker. 4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1 ☞...
  • Page 12 Menu Configuration—MAIN MENU (cont.) AUDIO SETTING Settings for the audio output balance, EMBEDDED AUDIO signals and level meter Item To do Setting value BALANCE Adjust the balance between the right and left L5 – L1, 0, R1 – R5 speakers. AUDIO1 ASSIGN.
  • Page 13 WAVE FORM SETTING* Settings for the wave form monitor Item To do Setting value POSITION Select the position of the wave form monitor. 1 (lower right), 2 (lower left), 3 (upper left), 4 (upper right) FILTER Activates/deactivates the low-pass filter for the FLAT (no filter), LOWPASS incoming wave form data.
  • Page 14: Menu Configuration-Set-Up Menu

    Menu Configuration—SET-UP MENU FUNCTION SETTING For the operation procedure, see page 7. Setting for the sub menu display, color system, color of the tally lamp and the picture size. Item To do Setting value ☞ “NOTE” sub menu POSI. Select the contents and displaying position of “sub menu.” COLOR Select the color system.
  • Page 15 REMOTE SETTING (☞ “External Control” on pages 16 to 18) Settings for the external control Item To do Setting value SERIAL TYPE Select the input terminal used for external control by RS232C, RS485 serial communication. PARALLEL TYPE Select the external control method for the MAKE/ MAKE, TRIGGER, SET TRIGGER terminal.
  • Page 16: External Control

    External Control 7 About the external control Control priority is as follows. MAKE > TRIGGER = serial communication = buttons and menu on the monitor This monitor has three external control terminals. • You can use the external control even when “CONTROL LOCK” is set to “ON” (☞ page 15). •...
  • Page 17: Using The Make/Trigger System

    7 Using the MAKE/TRIGGER system <Functions controlled by the MAKE/TRIGGER system> Display Functions to be controlled Opening Short-circuiting The MAKE/TRIGGER terminal is configured as follows. You can assign a function to each pin terminal in TALLY SEL Selects the color of the tally lamp. Green “REMOTE SETTING”...
  • Page 18: Using The Serial Communication

    External Control (cont.) 7 Using the serial communication Example of communication procedures 1 Starting the communication: You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal. connection command (!00BCN1Cr) • Consult your dealer for the details of the external control specification. Monitor 2 Monitor’s status (@00BOKCr) <Communication specifications>...
  • Page 19: Troubleshooting

    Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page Symptom Probable cause and corrective action Page...
  • Page 20: Self-Check Program

    Troubleshooting (cont.) Maintenance 7 Self-check program Unplug this product from the wall outlet before cleaning. This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes Screen troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be happens, follow the steps below and contact your dealer to resolve the problem.
  • Page 21: Specifications

    Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.
  • Page 22: Dimensions

    Specifications (cont.) 7 Dimensions Unit: mm (inch) DT-V24L3D <Side view> <Front view> <Rear view> 99 (4) 51.9 (2 1/8) VESA mounting holes 564 (22 1/4) (Size: 4-M4, depth: 10 mm) 1.5 (1/16) 51 (2 1/8) 300 (11 7/8) 243 (9 5/8) DT-V20L3D <Side view>...
  • Page 24 DT-V24L3D/DT-V20L3D MULTI FORMAT LCD MONITOR © 2008 Victor Company of Japan, Limited 0908TKH-MW-MT...

This manual is also suitable for:

Dt-v24l3dDt-v20l3d

Table of Contents