Setting The Video Options - Pioneer Elite SC-37 Operating Instructions Manual

09 Using other functions
f. • The HDMI Audio setting cannot be switched while performing
synchronized amp mode operations.
• The synchronized amp mode must be turned on in order to play
the receiver's HDMI audio and video input signals from the TV with
the receiver's power in the standby mode. See About synchronized
operations on page 74.
g.This feature is only available when the connected display supports
the automatic audio/video synchronizing capability ('lipsync') for
HDMI. If you find the automatically set delay time unsuitable, set A.
DELAY to OFF and adjust the delay time manually. For more details
about the lipsync feature of your display, contact the manufacturer
directly.
h.Only when listening to 2-channel sources in Dolby Pro Logic IIx
Music/Dolby Pro Logic II Music mode.
i. Only when listening to 2-channel sources in Neo:6 MUSIC/CINEMA
mode.
j. • You can't use the Virtual Surround Back mode when the
headphones are connected to this receiver or when any of the
stereo, Front Stage Surround Advance, Sound Retriever Air or
Stream Direct modes is selected.
• You can only use the Virtual Surround Back mode if the surround
speakers are on and the SB setting is set to NO or if Front Bi-Amp
or ZONE 2 is selected at Speaker System. It can also be used when
Speaker B is selected at Speaker system and SPAB is selected
with the SPEAKERS button.
• When inputting Dolby True HD (SC-35 only), DTS-HD or DTS
Express audio signals, the Virtual Surround Back mode cannot be
used if no surround signals are recorded in the source.
k.• You can't use the Virtual Height mode when the headphones are
connected to this receiver or when any of the stereo, Front Stage
Surround Advance, Sound Retriever Air or Stream Direct modes is
selected.
• The Virtual Height mode cannot be used when no surround
speaker is connected.
• When inputting Dolby True HD (SC-35 only), DTS-HD or DTS
Express audio signals, the Virtual Height mode cannot be used if no
surround signals are recorded in the source.

Setting the Video options

There are a number of additional picture settings you can
make using the VIDEO PARAMETER menu. The defaults,
if not stated, are listed in bold.
Important
• Note that if an option cannot be selected on the
VIDEO PARAMETER menu, it is unavailable due to
the current source, setting and status of the receiver.
• All of the setting items can be set for each input
function.
• Setting items other than V. CONV can only be
selected when V. CONV is set to ON.
78
En
1 Set the remote control to the receiver operation
mode, then press VIDEO PARAMETER.
Use / to select the setting you want to adjust.
2
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
Use / to set as necessary.
3
See the table below for the options available for each
setting.
4 Press RETURN to confirm and exit the menu.
Setting What it does
Converts video signals for output
a
V. CONV
from the MONITOR OUT jacks
(Digital Video
(including HDMI OUT connector)
Conversion)
for all video types (see page 27).
Specifies the output resolution of
b
RES
the video signal (when video input
(Resolution)
signals are output at the HDMI
OUT connector, select this
according to the resolution of your
monitor and the images you wish
to watch).
c Specifies the aspect ratio when
ASP
input signals are output at the
(Aspect)
HDMI output. Make your desired
settings while checking each
setting on your display (if the
image doesn't match your monitor
type, cropping or black bands
appear).
d,e This setting optimizes the
PCINEMA
operation of the progressive
(PureCinema)
scanning circuit for playing film
materials. Normally set it to AUTO.
If the picture seems unnatural,
switch this to ON or OFF.
d,e Adjusts the motion and still picture
P.MOTION
quality when video output is
(Progressive
progressive.
Motion)
d Reduces noise in the luminance
YNR
(Y) signal.
Reduces noise in the input's color
d
CNR
(C) signal.
d Reduces block noise (block-
BNR
shaped distortion generated upon
MPEG compression) in the
picture.
Reduces mosquito noise
d
MNR
(distortion generated at the
contours of the picture upon
MPEG compression) in the
picture.
d Adjusts how sharp edges appear.
DETAIL
Option(s)
ON
OFF
AUTO
PURE
480p/576p
720p
1080i
1080p
1080/24p
THROUGH
NORMAL
AUTO
ON
OFF
–4 to +4
set to
Default: 0
0 to +8
Default: 0
0 to +8
Default: 0
0 to +8
Default: 0
0 to +8
Default: 0
0 to +8
Default: 0