Table of Contents
Advertisement
en Rapid heating
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
Press
"Info".
1.
a Information is displayed for a few seconds.
To scroll through lots of content in the message,
2.
swipe over the display.
3.
If necessary, use
8.8 Sabbath-compliant use
If you want to operate your appliance so that it is Sab-
bath-compliant, use the time-setting options and
change the basic setting for the lighting.
Note: If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
operate your appliance so that it is Sabbath-compliant,
do not open the appliance door until after operation.
Change the "Lighting" basic setting to "Always off".
1.
→ "Basic settings", Page 19
This will ensure that the light in the cooking com-
partment is always off while the appliance is in oper-
ation and when you open the appliance door.
9 Rapid heating
To save time, rapid heating
ing time for set temperatures over 100 °C.
Rapid heating is possible for the following types of
heating:
¡ 4D hot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note: Do not set a cooking time until rapid heating has
come to an end.
10 Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
12
to exit the message.
can shorten the preheat-
Set the required operating mode.
2.
→ "Setting the operating mode", Page 11
→ "Setting the type of heating and the temperature",
Page 11
Set the required cooking time depending on the op-
3.
erating mode.
→ "Setting the cooking time", Page 13
→ "Time-setting options", Page 12
Use "End time" to set the time at which the opera-
4.
tion should end.
→ "Setting the end time", Page 13
→ "Time-setting options", Page 12
Place the food in the cooking compartment before
5.
the appliance starts to heat.
Press
to start the operation.
6.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
7.
When the operation has ended, remove the food
from the cooking compartment. The appliance auto-
matically switches off completely after approximately
15 to 20 minutes.
Note: If necessary, change the basic setting for the
lighting again.
Set a suitable type of heating and a temperature of
1.
at least 100 °C.
Rapid heating automatically switches off at temper-
atures of 200 °C and above.
2.
Press "Rapid heating".
a The
symbol lights up red.
Press
to start the operation.
3.
a Rapid heating starts.
a Once rapid heating has ended, a signal sounds.
The
symbol changes back to white.
Place the food in the cooking compartment.
4.
Cancelling rapid heating
Press
on the display.
1.
Press "Rapid heating".
2.
a The
symbol changes back to white.
Time-setting
Use
option
End time
Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
Advertisement
Table of Contents
