Download
Share
Print this page
Husqvarna TF 440 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Tiller
  5. TF 440
  6. Operator's manual
Husqvarna TF 440 Operator's Manual

Husqvarna TF 440 Operator's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
TF 440
1-１４
EN
Operator's manual

Advertisement

loading

Related Manuals for Husqvarna TF 440

Summary of Contents for Husqvarna TF 440

  • Page 1 TF 440 1-１４ Operator's manual...
  • Page 2 a X19 c X 4 d X 4 e X 23 f X 6 g X2 X 32 X 32...
  • Page 3 n x2 r x32 o x2 s x32 p x2 t x32 q x2...

  • Page 6: Table Of Contents

    Content Introduction..............6 Maintenence............11 Trobleshooting............12 Safety.................7 Transportation and Storage........14 Assembly..............8 Technical Data............14 Operation..............9 Introductio Product overview (Fig. 9) Keep bystanders away from the product (Fig. 10) Neutral gear (Fig. 1) (Fig. 11) Reverse gear 1. Blades connector (Fig. 12) Fast forward 2.

  • Page 7: Safety

    • If you have problems or questions about the product, moving parts. Use hearing protection to minimize the please speak to your Husqvarna dealer for more risk of hearing impairment. information. •...

  • Page 8: Assembly

    lead to serious injury or death to the user or others. • Bear in mind the risk of fire, explosion and inhaling The warranty is not valid if non genuine parts are fumes. If you spill fuel on yourself or your clothes, used.

  • Page 9: Operation

    Note that the installation position of the circlip needs to 3. Mount the handle frame on the handle seat, insert M16*140 bolt and locking knob refer to Fig. 35. be in the top slot. To assemble the tine left blades (view from 4.
  • Page 10 d) Do a check of all nuts and screws. 5. Release the clutch handle (A) to make the tine blades stop. (Fig.57) e) Make sure that the electrical wires are not damaged. To operate the product rearward f) Apply oil to the air filter. g) Fill the air filter holder with 100ml oil.

  • Page 11: Maintenence

    Maintenance WARNING Clean at a more regular interval if the product is used Read and understand the in conditions with much dust. safety chapter before you do maintenance on the product. ** Maintenance is only necessary if operation problems occur. Speak to an approved servicing dealer Maintenance schedule Maintenance interval Daily maintenance...

  • Page 12: Trobleshooting

    Troubleshooting Table I Troubleshooting of engines Problem Cause Solution Engine switch is “OFF” Turn on engine switch Low oil level Fill oil to correct level Fuel Valve is “OFF” Turn fuel Valve”ON” Out of fuel Fill fuel Press the safety button, turn on the Fuel cannot flow into carburetor carburetor switch and turn the fuel valve “ON”...
  • Page 13 Oil leakage at main shaft Oil seal failure on main shaft Replace oil seal Oil leakage at reverse fork O-ring seal failure Replace O-ring seal shaft Reverse shaft rear bolt is loose or not Tighten the connecting bolts of the reverse tightened shaft and gearbox Oil leakage at reverse shaft...

  • Page 14: Transportation And Storage

    Be careful when you move the product on or off a product. Sparks or open flames, for example from vehicle for transportation. Use an approved ramp electrical devices or boilers, can start a fire. Technical Data TF 440 Working width 1050mm Working depth 150-300mm...
  • Page 15 Original instructions 1143817-26...