Table of Contents
Advertisement
PRELIMINARY OPERATIONS
About Back-ups
1. When
the power
switch
is in the STANDBY
position .
When the power is turned on again, the SLEEP
TIMER and
MUTING will be reset, but all other switch settings will return
to the previous settings before entering the standby mode.
BASIC OPERATIONS
2. When AC power has been cut.........0.0.04
{1}
Ail settings but the SLEEP TIMER and MUTING
will be
preserved
for a several days be the internal back-up
function, even if the AC power is cut.
(2)
The
internal
back-up
information
wili be lost after a
several days without external power.
RECORD PLAY
Manual play (PL-202AZ, PL-222Z, PL-322AZ, PL-
3222)
1. Perform the preliminary operations.
~ 2. Place the record on the piatter mat.
3. Remove the stylus cover and release the tonearm from the
arm rest.
4, Set the SPEED switch,
5. Move the ARM ELEVATION
switch to the UP position.
6. Move the tonearm by Nand across the record. At this stage,
the platter starts to rotate.
_ 7. Move the ARM ELEVATION switch to the DOWN position.
.8. Adjust the Volumie with the VOLUME
control and the tone
with the GRAPHIC EQUALIZER controls.
9. To stop the player, press 'the STOP {or PLAY/STOP) switch.
pati play (PL-322482, PEB222)
or
. Perform the prelininary operations.
Z Place the record on the piatter mat. _
3. Remove the stylus cover and release the tonearm from the
arm rest.
. Set the SPEED and SIZE switches.
. Move the ARM ELEVATION switch to the DOWN position.
. Push the PLAY/STOP switch to start record play.
. Adjust the volume with the VOLUME
control and the tone
with the GRAPHIC EQUALIZER controls.
. . To stop the player, préss the PLAY/STOP switch.
OTE:
When play is completed, the tonearm will return automatically
to the arm rest.
*
When playing 45 rpm records with large center holes, place
the EP adaptor onto the piatter spindie.
LISTENING TO THE BROADCASTS
620
Nos
BAND sélector switch
MEMORY.
switch
STATION CALL
TUNING
switches
switches
1. Perform the preliminary operations.
2, Select
your
desired
broadcasting
band
using
the
BAND
selectar switch,
3. Press the TUNING
switch to locate the frequency of your
desired station.
Auto tuning:
Press the tuning switch until the
frequency starts to change {about
tseconds}, then release it.
10
<ARB1179>
The tuner will automatically search for a broadcasting station,
and stop when one is found. To search for another station, press
again.
* To interrupt auto tuning, press the TUNING switch again.
NOTE:
When AUTO
TUNING is in use, reception may not be possible
over jong distances or when signals are weak. At these times
MANUAL
TUNING is recommended.
Manual tuning:
*
xm
Press and release quickly.
The tuning frequency
will change
by one step each time the
switch is pressed. Press as many times as necessary to tune in
the desired station.
® {f the switch is heid depressed for more than approximately 2
seconds, the reception frequency will change continuously,
and stop when the switch is released.
NOTE:
The TUNED indicator will not function for broadcasts received
over jong distances or when signals are weak.
4. Adjust the volume with the VOLUME
control and the tone
with the GRAPHIC EQUALIZER controls,
PRESETTING STATIONS
Presetting
From 1 to.24 ©M/AM stations can be preset at random. Press the
STATION CALL switch once for 1 - 12 (Mode 1) and twice:for 13 -
24 (Mode 2}
The setting of the FM MONO
switch is aiso recorded with the
preset station frequency.
1. Tune in desired station.
* See "LISTENING
TO THE
BROADCASTS"
section
for
infermation on reception.
2. Press the MEMORY switch.
* The display will flash {about 5 seconds}.
MEMORY
—
A
3. Press one of the STATION CALL switch.
* While
the
display
is
flashing,
press
the
switch
corresponding to the station which you wish to preset or
re-preset.
Frequency
display
Advertisement
Table of Contents
