Using The Play Timer.26 - Panasonic SC-AK20 Operating Instructions Manual

Using the ploy timer
I'repar.iMons
• Make sure that you have completed "Setting the time" on page 9.
• Switch on the power.
The following example in the figure shows how to set the play timer
for playing a CD from 6:30 a.m. to 7:40 a.m.
n
Press CLOCK/TIMER to select "©PLAY".
0 Every time you press the button;
CLOCK ^ ©REC ©PLAY
— Previous display <-
^
0 (Within 10 seconds or so)
Press MEMORY/SET.
"ON" lime setting
(0
Press
V
or
A
to select the starting hour.
@ Press MEMORY/SET.
0)
Press
V
or
A
to select the starting minutes.
® Press MEMORY/SET.
"OFF" time setting
0
Press
V
or
A
to select the ending hour.
0
Press MEMORY/SET.
0
Press
V
or
A
to select the ending minutes.
0
Press MEMORY/SET.
□
Source selection
Select the desired source and then prepare for
playing.
When you play CD(s)
Press CD and insert CD(s).
If more than 1
CD
is loaded
Press DISC 1 - DISC 5 to select the CD you want to hear first,
and press ■.
When you play tape(8)
Press TAPE DECK 1/2 and insert tape(s).
If tapes are loaded in both decks, playback will start from deck
2.
When you play the radio
Press TUNER BAND and tune in the desired station.
When you play a unit connected to the "AUX" terminals
Press AUX.
Ploy volume setting
Set the playback volume.
Press ©PLAY/0REC to select "©PLAY ".
Every time you press the button;
©REC-> ©PLAY
"L- Out (OFF) <-1
Power will shut OFF automatically in a few seconds.
The timer play will start at the preset time with volume
increasing gradually up to the volume level you preset.
To switch the timer OFF:
Press ©PLAY/©REC and check "©PLAY" goes out.
If you set the timer wrongly
Press ©PLAY/©REC so that "©PLAY" goes out. Then, repeat the
procedure from step 1.
To check settings
Press CLOCK/TIMER to select "©PLAY".
Two seconds later, the display will change in'the following order.
0 Play start time
0 Play over time
0 Play source and playback volume
You can check settings even when power is OFF.
To enjoy the desired source after the timer setting Is
completed
Even if you change the volume level or music source, the timer play
will start with the preset condition.
1. Following step 6, turn ON the power and start playing the desired
source.
When you select a CD as the program source
After the CD finishes, if more than 2 CDs are loaded in the player,
reset the programmed CD with DISC 1 ~ DISC 5, and press ■.
2. Press POWER to standby mode after enjoying the play, and
confirm CD(s) or tape(s) has (have) been inserted.
Turning the timer ON/OFF
As long as "©PLAY" is displayed, the play timer will come ON
everyday as set.
You can turn the timer ON/OFF by pressing ®PLAY/®REC while
power is OFF.
Remember that when "©PLAY" is displayed, the timer is ON. When
not displayed, the timer is OFF.
•
If the power is on, the timer will not function. The system must be
in the standby mode.
• If you switch the power to the standby mode while the play dmer
is functioning, the OFF time setting will not be activated.
• If AUX is selected as the source, when the timer comes ON, the
system will turn ON and will engage "AUX" as the source. If you
want playback from the connected component to start, set the
componenPs timer to the same time. (See the instruction manual
that came with the component.)
27