Advertisement
Due to our policy of continuous improvement, the actual product may differ slightly from the one illustrated in these instructions.
Remove all packaging including any soleplate protection before operating your steam generator.
Wipe over the soleplate with a soft cloth.
Position your steam generator iron horizontally on your ironing board (if it is large enough) or on a heat resistant and secure surface at the same height as your ironing board.
Before connecting your steam generator to the mains supply, make sure your supply voltage is the same as the one indicated on your steam generator.
When you first use your steam generator, there may be a slight odour and it may smoke slightly for the first few minutes of operation. This is quite normal and will disappear.
When you first use your steam generator, iron an old towel to ensure that any residues inside the iron are not transferred to your laundry.
Never add fabric conditioner, starches or any other chemicals to the water in your steam generator.
Note that when you use your steam generator for the first time or after rinsing the boiler, a lot of water will be pumped out of the water tank. Refill the tank as required.
You can fill your steam generator during use without having to remove the water tank. The water tank empty indicator light will flash to let you know that the water tank needs filling.
Simply open the water tank filling cover and add water as required. Do not fill past the MAX indicator mark on the tank.
We recommend that you:
Your steam generator takes time to heat up and cool down. If you change the temperature setting on your steam generator, you must give it time to adjust to the new setting.
This is especially important when you change from a high setting to a lower one. It takes your steam generator longer to cool down than it does to heat up and this is the reason we recommend that you begin ironing at lower temperatures.
If you do need to reduce the temperature of your steam generator, wait until the temperature indicator light flashes and then comes on again before ironing. This will ensure that your steam generator has cooled to the lower temperature and is not too hot for the fabric being ironed.
For example, you have been ironing using the setting and wish to change to the setting:
During steam ironing, if you do not allow your iron to reach the selected temperature water may drip from the soleplate. During use the steam pipe and iron rest become very hot.
It is recommended that for harder to iron fabrics such as cotton and linen, steam should be used when ironing.
When ironing cotton and linen, always select the highest temperature. Steam should never be used on delicate fabrics like nylons, acrylics and synthetics.
If you intend to dry-iron fabrics there is no need to fill the water tank. However, if water is already in the water tank, you do not need to empty it.
Vertical steam ironing is especially useful for ironing items such as curtains while they are hanging, or jackets, suits and coats.
Hold the iron in a vertical position and press the steam trigger as required.
To prevent fatigue, your steam generator can be set to produce steam without having to constantly hold the steam trigger in the on position.
ALWAYS disconnect your iron from the mains supply socket after use. NEVER leave the iron unattended with the auto off function in operation.
Your steam geneator will automatically switch to auto off mode if you leave the iron resting in its soleplate for more than 30 seconds, or on its heel for more than 15 minutes.
The on/off button light, temperature indicator light, temperature display lights and Breville logo light on the rear panel of the iron will flash to show that your steam generator is in auto off mode.
To reactivate your steam generator, lift and gently shake the iron or press any button on the control panel.
Never rely on the auto off mode to switch off your steam generator after use. After use, always switch off your steam generator using the on/off switch and unplug it from the mains supply socket.
The anti-calc cartridge should be replaced when the anti-calc cartridge indicator light flashes. If a new cartridge is not immediately available you may continue ironing using distilled water in place of tap water.
When the anti-calc cartridge requires renewal, do NOT continue to use your steam generator with tap water as this may cause damage. NEVER attempt to use your steam generator without the anti-calc cartridge in place.
Do not use harsh abrasives, chemical cleaners or solvents to clean the exterior of your steam generator because they will damage the surface.
After each use, allow your steam generator to completely cool down before wiping the soleplate with a soft damp cloth. If polyester has burnt to the soleplate, iron a damp cotton cloth while your steam generator is still hot. If necessary, allow your steam generator to completely cool down then wipe over the soleplate with a soft cloth moistened with methylated spirits. Remove the methylated spirit with a damp cloth. Make sure that the soleplate is completely dry.
To clean the exterior of your steam generator, wipe over with a soft damp cloth and wipe dry. Ensure the soleplate is dry.
To remove build-up from the steam holes which may affect steam performance, use a cotton wool tip moistened in methylated spirits. Wipe over with a damp cloth.
NEVER remove the boiler rinse plug when your steam generator is hot. Allow your steam generator to cool for at least 2 hours before removing the boiler rinse plug.
To maintain optimum performance, it is important to rinse out the boiler in your steam generator once a month or after every 10 times you have used it.
Unplug your steam generator and allow it to cool for at least 2 hours. Remove the water tank.
Problem | Possible cause | Solution |
My steam generator doesn't heat up. | Your steam generator is not connected properly. | Check the mains power cord, plug and wall socket. |
Your steam generator is not switched on. | Press the on/off switch to switch your steam generator on. | |
The temperaure is set to MIN. | Set the temperature to the required temperature. | |
My steam generator does not produce any steam. | There is not enough water in the water tank. | Fill the water tank as required. |
Your steam generator's boiler is still heating up. | Wait until the heat indicator light stops flashing and goes out. | |
The selected temperature is too low for steam ironing. | Set the temperature to MED or higher. | |
The water tank is not fitted correctly. | Check that the water tank is correctly fitted. | |
The steam may not be visible if your steam generator is set to a high ironing temperature. | Set your steam generator to a lower temperature (e.g. MED) to check if steam is being produced. | |
Water droplets come out of the soleplate. | The selected temperature is too low for steam ironing. | Set the temperature to MED or higher. |
If you have left your steam generator for some time between ironing, steam left in the steam hose can cool down and cause water dropets to form. | This is normal. Hold your iron over an old cloth and press the steam trigger until steam rather than water droplets come from the soleplate. | |
My steam generator occasionally makes a strange sound. | This is the internal pump transferring water from the water tank as required. | This is normal. The pump active light will illuminate when the pump is operating. |
Dirty water comes out of the soleplate. | Scale and other impurities have accumulated inside the boiler of your steam generator. | Allow your steam generator to fully cool down then rinse the boiler—see care and cleaning. |
This appliance must be earthed.
Plug should be BS1363 approved Fit a 13 Amp Fuse
Ensure that the outer sheath of the cable is firmly held by the clamp
This appliance is fitted with either a moulded or rewirable BS1363, 13 amp plug. The fuse should be rated at 13 amps and be ASTA approved to BS1362.
If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The appliance must not be used without the fuse cover fitted.
If the plug is unsuitable, it should be dismantled and removed from the supply cord and an appropriate plug fitted as detailed below. If you remove the plug it must not be connected to a 13 amp socket and the plug must be disposed of immediately.
The wires of the mains lead are coloured in accordance with the following code:
GREEN/YELLOW = EARTH
BLUE = NEUTRAL
BROWN = LIVE
The wire which is coloured GREEN/YELLOW must be connected to the terminal in your plug which is marked with an E or by the earth symbol () or coloured GREEN or GREEN /YELLOW.
The wire which is coloured BLUE must be connected to the terminal in your plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in your plug which is marked with the letter L or coloured RED.
If any other plug is used, a 13 amp fuse must be fitted either in the plug or adaptor or at the distributor board.
These appliances are built to the very highest of standards. There are no user serviceable parts. Follow these steps if the unit fails to operate:
If the appliance will still not operate, return the appliance to the place it was purchased for a replacement. To return the appliance to the Customer Service Department, follow the steps below:
Customer Service Department
Jarden Consumer Solutions (Europe) Limited
Middleton Road
Royton
Oldham
OL2 5LN, UK.
Telephone: 0161 621 6900
Fax: 0161 626 0391
e-mail: info@pulse-uk.co.uk
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
This product can be used by children aged 8 years and above, and persons who require supervision, provided:
Children must not play with the product. Cleaning and user maintenance must not be done by children unless they are supervised.
Keep the appliance and its cord out of reach of children less than 8 years old when it is switched on or cooling down.
The appliance must not be left unattended when it is connected to the mains supply.
The appliance must be unplugged from the mains supply socket before filling the water tank with water.
Always use the appliance on a stable, secure, dry and level surface. When placing the appliance on its stand, ensure that the surface on which the stand is placed is stable.
Do not use the appliance if it has been dropped, if there are any visible signs of damage or if it is leaking.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Breville VIN170 - 2400W Digital Steam Generator Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the VIN170 that isn't answered in the manual? Leave your question here.