Breville HotCup VKJ142 - Hot Water Dispenser Manual

parts and features

1. On/Off button
   Lights up blue when in the on position.
2. Lid
3. Lid release button
   Press to open the lid and fill the water tank.
4. Illuminated water reservoir
   Easy fill water reservoir holds up to 1.5 litres.
5. Heating chamber
6. Dispensing nozzle
7. Stainless steel drip tray cover
8. Removable drip tray
   No mess, just lift it out and rinse under the tap. Holds over 1 cup of water before it needs emptying.
9. Power base

using your product

Before using your HotCup water dispenser for the first time

• Remove your HotCup water dispenser carefully from the box. Remove any packaging and promotional material and position it on a dry, level, secure work surface away from the edge.
• Follow the instructions below on using your HotCup water dispenser and discard the first five measures of boiling water (i.e. the first full tank of water). This will remove any residues that may remain from the manufacturing process.

Using your HotCup water dispenser
Always position your HotCup water dispenser in such a way that the on/off switch cannot be accidentally operated especially by children.

1. Press the lid release button.
   
2. Fill the water reservoir from your cold tap. The water level should be between the MIN and MAX markings.
   
3. Close the lid and position your HotCup water dispenser on the power base. Make sure the on/off switch is in the off position, then plug your HotCup water dispenser in to a mains supply socket. Place a suitable cup or container with a tea bag, coffee, sugar, etc. below the dispensing nozzle. Never operate your HotCup water dispenser without a cup or suitable container placed below the dispensing nozzle.
   
4. Press the on/off switch down to its on position. The switch will light up blue.
   
5. A few seconds before the water has finished dispensing, the on/off switch will automatically switch to its off position.
   
6. Boiling water will be dispensed into the cup. Your HotCup water dispenser is now ready to use again. If, after just having boiled, the on/off switch doesn't stay in the on position, wait a few seconds before trying it again.
   

Always keep your HotCup water dispenser topped up with water (between the MIN and MAX markings). That way you'll ensure that it's always ready to use and don't forget, unlike an ordinary kettle, this will have no effect on the energy your HotCup water dispenser uses.

Beware of accidentally operating the on/off switch. If you do, immediately switch it off again.

If your HotCup water dispenser has been switched on for more than 15 seconds, hot water will still be dispensed. Do not attempt to move your HotCup water dispenser from the power base. Allow the water to escape into the drip tray. Beware of hot water splashing from the drip tray.

If you have started the boil procedure and then decide to switch off your HotCup water dispenser, always allow it to stand for 1 minute before removing it from the power base for refilling etc.

cleaning

Always switch off and unplug your HotCup water dispenser and allow it to completely cool before cleaning. Never immerse the base unit, power cord or plug in water or any other liquid. Do not use harsh abrasives, chemicals or oven cleaners.

Emptying your Device

1. After your HotCup water dispenser has completely cooled down, unplug it from the mains supply socket.
2. Press the lid release button.
   
3. Hold your HotCup water dispenser sideways over a sink.
   
4. Then, tip your HotCup water dispenser upside down.
   
5. Still holding it over the sink, turn it the right side up and allow any water to drain out of the dispensing nozzle.
   
6. Repeat steps 3, 4 and 5 until the water has been emptied out.

If your HotCup water dispenser will not be used for an extended period (e.g. if you are on holiday), we recommend that you first empty it. Before using your HotCup water dispenser again, carry out several boil cycles discarding the water each time.

Cleaning

Clean the exterior surface of the kettle with a damp cloth and then polish with a soft dry cloth. Do not use steel wool pads or harsh/abrasive cleaners.

safety and efficiency

To ensure the safe and efficient operation of your HotCup water dispenser it is important to descale it regularly. The harder your water the more regularly it will need doing. Your water company should be able to tell you how hard the water is in your area. Untreated scale deposits prevent the element conducting heat efficiently therefore wasting electricity. Scale can also cause your HotCup water dispenser to malfunction or even cause premature failure.

Descaling using a proprietary descaling product

1. Fill your HotCup water dispenser to the MAX fill level and place an empty cup on the drip tray. Set the on/off switch to the on position and wait for the water to be dispensed into the cup.
   
2. Add a citric acid-based descaling product to the hot water in the cup and stir.
   
3. Tip the contents of the cup into your HotCup water dispenser and close the lid.
   
4. Place the empty cup on the drip tray and set the on/off switch to the on position.
   
5. Wait for the water to be dispensed into the cup.
   
6. Discard the water from the cup.
   
7. Repeat steps 4, 5 and 6 until the water level is at the MIN mark. Open the lid and empty any remaining water into the sink. Rinse your HotCup water dispenser by filling it with clean water and emptying it into the sink (see Emptying your Device).
   Fill with fresh water to the MAX fill level and place an empty cup on the drip tray.
   
8. Set the on/off switch to the on position and wait for the water to be dispensed into the cup.
   
9. Discard the water in the cup. Repeat steps 8 and 9 until the water level is at the MIN mark. Open the lid and empty any remaining water into the sink (see Emptying your Device).
   

Descaling using vinegar or citric acid

1. You can use ordinary vinegar (white or malt) or citric acid to descale your HotCup water dispenser. Inexpensive, ordinary vinegar can be purchased in large bottles from any supermarket. Citric acid can be bought from pharmacies, home brewing/ winemaking suppliers or on-line retailers.
2. If you are using vinegar, make up a solution of 1 cup of vinegar to 1 cup of water. If you are using citric acid, mix 30g of the citric acid with 500ml of water.
3. Pour the solution into your HotCup water dispenser, close the lid and allow it to stand for 1 hour.
4. Cycle your HotCup water dispenser (as described in steps 4-6 above) until the level is at the MIN mark. Open the lid and empty any remaining solution into the sink. Rinse several times by filling it with clean water and emptying it into the sink.
5. Fill your HotCup water dispenser with fresh water to the MAX fill level and place an empty cup on the drip tray.
6. Set the on/off switch to the on position and wait for the water to be dispensed into the cup.
7. Discard the water in the cup. Repeat steps 6 and 7 until the water level is at the MIN mark. Open the lid and empty any remaining water into the sink.
8. Finally, rinse your HotCup water dispenser several times with clean water.

troubleshooting

connection to the mains supply

If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type.

If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The appliance must not be used without the fuse cover fitted.

If the plug is unsuitable, it should be dismantled and removed from the supply cord and an appropriate plug fitted as detailed. If you remove the plug it must not be connected to a 13 amp socket and the plug must be disposed of immediately.

If the terminals in the plug are not marked or if you are unsure about the installation of the plug please contact a qualified electrician.

Plug should be BS1363 approved
Fit a 13 Amp Fuse
Ensure that the outer sheath of the cable is firmly held by the clamp

after sales service

These appliances are built to the very highest of standards. There are no user serviceable parts. Follow these steps if the unit fails to operate:

1. Check the instructions have been followed correctly.
2. Check that the fuse has not blown.
3. Check that the mains supply is functional.

If the appliance will still not operate, return the appliance to the place it was purchased for a replacement. To return the appliance to the Customer Service Department, follow the steps below:

1. Pack it carefully (preferably in the original carton). Ensure the unit is clean.
2. Enclose your name and address and quote the model number on all correspondence.
3. Give the reason why you are returning it.
4. If within the guarantee period, state when and where it was purchased and include proof of purchase (e.g. till receipt).
5. Send it to our Customer Service Department at the address below:
   Customer Service Department
   Jarden Consumer Solutions (Europe) Limited
   Middleton Road, Royton, Oldham OL2 5LN, UK.
   Telephone: 0800 525 089 Fax: 0161 626 0391
   e-mail: enquiriesEurope@jardencs.com

Turn on your creativity
Let the Breville team help you turn on your creativity with a gateway to a world of food and drinks without limits. You don't have to travel far—just to your computer, tablet or mobile—where you will discover our FREE website with top tips and recipes to inspire your imagination. Join us now at www.turnonyourcreativity.com

product safety

READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of the reach of children aged less than 8 years.
Never use a power base other than the one supplied with the appliance.
Never fill the kettle above the MAX marking. If the kettle is overfilled, boiling water may be ejected.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

This appliance generates heat during use. Adequate precaution must be taken to prevent the risk of burns, scalds, fires or other damage to persons or property caused by touching the exterior whilst in use or during cooling.
Never use this appliance for anything other than its intended use. This appliance is for household use only. Do not use this appliance outdoors.
Always ensure that hands are dry before handling the plug or switching on the appliance.
Always use the appliance on a stable, secure, dry and level surface.
This appliance must not be placed on or near any potentially hot surfaces (such as a gas or electric hob).
Do not use the appliance if it has been dropped, if there are any visible signs of damage or if it is leaking.
Ensure the appliance is switched off and unplugged from the supply socket after use and before cleaning.
Always allow the appliance to cool before cleaning or storing.
Never immerse any part of the appliance or power cord and plug in water or any other liquid.
Never let the power cord hang over the edge of a worktop, touch hot surfaces or become knotted, trapped or pinched.
Never leave the appliance unattended when in use.
Beware of steam coming from the spout or lid especially during refilling. Never open the lid during the boiling cycle.
Never fill the appliance when it is positioned on the power base.
Never use the kettle without sufficient water in the kettle for it to operate correctly.
Never allow the appliance to boil dry.

Documents / Resources

References

• High Quality Small Kitchen & Cooking Appliances | Breville

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Breville HotCup VKJ142 - Hot Water Dispenser Manual