Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Smeg SRV864AVOGH cerca il tuo prodotto tra le migliori offerte di Cucine e Piani cottura Contents 1. INSTRUCTIONS FOR USE .............. 26 2. SAFETY PRECAUTIONS ..............28 3. ENVIRONMENTAL RESPONSIBILITY..........30 4.
General instructions 1. INSTRUCTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB.
Page 3
General instructions ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE (OFF) POSITION WHEN YOU FINISH USING THE HOB. NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE COOKING HOB RACKS. NEVER USE CONTAINERS WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB.
General instructions 2. SAFETY PRECAUTIONS REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS. IN YOUR INTERESTS AND FOR YOUR SAFETY IT HAS BEEN ESTABLISHED BY LAW THAT THE INSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS TO BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE.
Page 5
General instructions DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME. DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE SLITS IN THE APPLIANCE. DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE. THE STEAM COULD REACH THE ELECTRONICS, DAMAGING THEM AND CAUSING SHORT-CIRCUITS.
Instructions for disposal 3. ENVIRONMENTAL RESPONSIBILITY Our environmental care Pursuant to Directives 2002/95/EC, 2002/96/EC, 2003/108/EC, relating to the reduction of the use of hazardous substances in electrical and electronic appliances, as well as to the disposal of refuse, the crossed out bin symbol on the appliance indicates that the product, at the end of its useful life, must be collected separately from other refuse.
Instructions for the user 4. USING THE HOB Before turning on the burners, make sure that the burners, flame-spreader crowns and racks are fitted correctly. In the ultra-rapid burner, notch A must be aligned with pin B. The supplied rack C is for use with woks (Chinese pans). The reduction D supplied only on open pan stand models is for use with small pans as well.
Page 8
Instructions for the user Practical tips for using the burners For better burner performance and minimum gas consumption, pans with flat, even bases and with lids should be used, and their size should be in proportion to the burner (see “4.3 Pan diameters”). During cooking, in order to avoid burns or damage to the hob top and to the glass lid (when present), all pans or griddles must be positioned within the cooking hob...
Page 9
Instructions for the user Electric hot plates 4.5.1 Switching on electric plates Hobs may be fitted with an electric hot plate of varying diameter. These are controlled by a selector; to switch them on, turn the knob to the desired position. Raised indicators make reading and use of the controls easier and clearer: each knob being connected to its corresponding electric hot plate by a rib.
Page 10
Instructions for the user PRECAUTIONS When the hot plate is switched on for the first time or if it has not been used for a long time, you must first eliminate any humidity that may have been absorbed by the insulating coating; to dry it out, leave the hot plate on for 30 minutes at position 1 on the selector knob.
Instructions for the user 5. CLEANING AND MAINTENANCE Important: DO NOT USE STEAM JETS FOR CLEANING THE HOB. Before performing any operations requiring access to powered parts, disconnect the appliance from the power supply. Cleaning the hob To keep the hob in good condition it should be cleaned regularly after use. Let it cool first.
Page 12
Instructions for the user Cleaning the cooking hob parts For easier cleaning the pan stands, burner caps, flame spreader crowns and burners can all be removed; wash them with warm water and a non-abrasive detergent making sure to remove any encrustation, then wait until they are perfectly dry.
Instructions for the installer 6. POSITIONING IN THE COUNTER TOP The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C).
Page 14
Instructions for the installer In case of installation on an empty kitchen unit with doors, a separation panel must be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the hob and the surface of the panel, which must be easily extractable to allow sufficient access for any technical assistance.
Instructions for the installer 7. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations.
Instructions for the installer 8. GAS CONNECTION If the appliance is installed on an oven, you must avoid running the gas tube round the back of the oven in order to avoid overheating. Connection to the gas supply network can be made using a rigid copper hose or a flexible steel hose with a continuous wall and in compliance with the guidelines established by the applicable standard.
Page 17
Instructions for the installer Connection to liquid gas Use a pressure regulator and make the connection on the gas cylinder following the guidelines set out in the regulations in force. Make sure that the supply pressure complies with the values indicated in the paragraph “3.2 Burner and nozzle characteristics tables”.
Instructions for the installer 9. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the power supply. The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted.
Page 19
Instructions for the installer Adjustment for LPG Loosen screw A and push support B all the way. Using a a double head, remove nozzle C and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. The nozzle tightening torque must be no more than 3 Nm.
Page 20
Instructions for the installer Adjustment for city gas Carry out the same steps as described in “9.2 Adjustment for LPG”, but select the nozzles and adjust the primary air for city gas as indicated in the table below and in "9.5 Primary air adjustment”. Rated heating Burner...
Page 21
Instructions for the installer Primary air adjustment Refers to distance “X” in mm. G30/G31 G110 BURNER 28/37 mbar 20 mbar 8 mbar Auxiliary (1) Semi-rapid (2) Rapid (3) Ultra-rapid (4) Double crown internal (5) external (5) 10.0 Fish burner (6) To identify the burners on your hob, refer to the drawings in “9.7 Arrangement of the burners on the cooking hob”.
Page 22
Instructions for the installer Arrangement of the burners on the cooking hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Ultra-rapid 5 Double crown 6 Fish burner Lubrication of gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease.