Table Of Contents; Product Specifications; Customer Responsibilities - Husqvarna 1130SBEXP Owner's Manual

6. Whencleaning, repairingorinspectingthesnowthrower,
stop theengine andmake certain thecollector/impeller
andall movingpartshavestopped. D isconnect the
sparkplugwireandkeepthewireawayfromtheplug
toprevent s omeone f romaccidentally starting theen-
gine.
7. Donot runthe engine indoors, e xcept w henstarting
theengine andfortransporting thesnowthrower i nor
outof thebuilding. O pentheoutside doors;exhaust
fumes aredangerous.
8. Exercise extreme caution whenoperating o nslopes.
9. Never o perate t hesnowthrower without proper g uards,
andothersafety protective d evices in place andwork-
ing.
10. Neverdirectthe discharge towardpeopleor areas
whereproperty damagecan occur. Keepchildren
andothersaway.
11. Donotoverload themachine capacity byattempting
toclearsnow at toofasta rate.
12. Neveroperate themachine at hightransport s peeds
onslippery surfaces. Lookbehind andusecarewhen
operating i n reverse.
13. Disengage p ower t othecollector/impeller whensnow
thrower i s transported o r notinuse.
14. Useonlyattachments andaccessories a pproved by
themanufacturer ofthesnow thrower ( suchaswheel
weights, counterweights, or cabs).
15. Never o perate t hesnow thrower w ithout g ood visibility
orlight. A lways besureofyourfooting, andkeepafirm
holdonthehandles. W alk;neverrun.
16. Never t oucha hotengine or muffler.
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the dis-
charge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
Maintenance and
Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator's manual for important details
if the snow thrower is to be stored for an extended
period.
4. Maintain or replace safety and instruction labels, as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
CONGRATULATIONS on your purchase of a new snow
thrower. It has been designed, engineered and manufactured
to give best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the "SAFETY RULES".
SERIAL NUMBER:
DATE OF PURCHASE:
THE MODELANDSERIAL NUMBERSWlLLBE FOUND
ON ADECALATTACHED TO THE REAR OFTHE SNOW
THROWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
PRODUCT SPECIFICATIONS
Gasoline Capacity 4.0 Quarts
and Type: Unleaded Regular only
Oil Type SAE 30 (above 40°F)
(API SG-SL): SAE 5W-30 or 10W-30 (0 ° to +40°F
SAE OW-30 (below O°F)
Oil Capacity: 26 Ounces
Spark Plug: Champion RN4C (Gap: .030")
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for
and using your snow thrower.
• Follow the instructions under"Maintenance" and "Stor-
age" sections of this owner's manual.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS ...................................... 3
CUSTOMER RESPONSIBILITIES ................................ 3
WARRANTY ................................................................ 32
ASSEMBLY / PRE-OPERATION ............................... 5-7
OPERATION ............................................................ 8-14
MAINTENANCE ..................................................... 14-15
MAINTENANCE SCHEDULE ..................................... 14
SERVICE AND ADJUSTMENTS ........................... 16-18
STORAGE ................................................................... 18
TROUBLESHOOTING ................................................ 19
REPAIR PARTS ..................................................... 20-31