Samsung PM32F-BC Quick Setup Manual

Quick Setup Guide
PM32F-BC
• The colour and the appearance may differ depending on the product, and the specifications are subject
to change without prior notice to improve the performance.
• Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
Checking the Components
Contact the vendor where you purchased the product if any components are missing.
Quick Setup Guide Warranty card (Not available in some
locations)
Batteries (Not available in some locations) USB cable
Screw (M3L8, 1 piece) Ring-type holder* (4 pieces)
* Use the provided Ring-type holder (HOLDER-WALL RING, BN61-14912A) to install the PM32F-BC model on the wall.
BN68-08272S-01
MagicInfo Software DVD Power cord
Remote Control RS232C(IN) adapter
USB cover
Reverse Side
TOUCH OUT
SCREEN
01
03 04 05 06 07
01 Connect to a USB port on the product to use the touch function.
02 Connect to a PC to use the touch function.
03 Connect to a USB memory device.
04 Connects to MDC using an RS232C adapter.
05 Receives sound from a source device via an audio cable.
06 Connects to the audio of a source device.
07 Connects to a source device using an HDMI cable.
Troubleshooting Guide
Issues Solutions
The screen keeps switching Check the cable connection between the product
on and off. and PC, and ensure the connection is secure.
No Signal is displayed on the Check that the product is connected correctly with
screen. a cable.
Check that the device connected to the product is
powered on.
Not Optimum Mode is This message is displayed when a signal from the
displayed. graphics card exceeds the product's maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set
the maximum resolution and frequency according
to the product specifications.
The images on the screen Check the cable connection to the product.
look distorted.
The screen is not clear. Adjust Coarse and Fine.
The screen is blurry.
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears unstable Check that the resolution and frequency of the
and shaky. PC and graphics card are set within a range
compatible with the product. Then, change the
There are shadows or ghost screen settings if required by referring to the
images left on the screen. Additional Information on the product menu and
the Standard Signal Mode Table.
TOUCH OUT
PC
02
DP IN DAISY CHAIN
08 09 10
08 DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
PC IN: Use the (dedicated) D-SUB - DVI cable (or D-SUB cable with D-SUB to DVI
adapter) when connecting a PC.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
09 Connects to a source device using a DP cable.
10 Connects to another product using a daisy chain (DP port) cable.
11 Connects to MDC using a LAN cable.
Issues Solutions
The screen is too bright. Adjust Brightness and Contrast.
The screen is too dark.
Screen color is inconsistent. Go to Picture and adjust the Color Space settings.
White does not really look Go to Picture and adjust the White Balance settings.
white.
There is no sound. Check the connection of the audio cable or adjust
the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
The remote control does not Make sure that the batteries are correctly in place
work. (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
RJ45
11