Download Print this page
ABB EMIU 1500W Instruction Manual

ABB EMIU 1500W Instruction Manual

4 option mini inverter
Hide thumbs Also See for EMIU 1500W:

Advertisement

Quick Links

THIS UNIT CONTAINS A
RECHARGEABLE VALVE-REGULATED
LEAD ACID BATTERY. PLEASE
RECYCLE OR DISPOSE OF
PROPERLY.
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ THIS MANUAL AND FOLLOW ALL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE OPERATING THE EMIU INVERTER SYSTEM
BEFORE CONTACTING TECHNICAL SUPPORT MAKE SURE TO FOLLOW ALL STEPS IN SEQUENCE AND REFER TO
THE TROUBLESHOOTING GUIDE INCLUDED IN THIS MANUAL.
1. Install in accordance with the National Electrical Code and local regulations.
2. The EMIU contains potentially hazardous voltages. Installation, maintenance and service work should be performed by qualified
and trained personnel.
3. Units to be installed only as per configuration described in this instruction manual.
4.
Electricians and end-users need to ensure product system compatibility before final installation.
5. The AC voltage rating of this equipment is specified on the product label. Do not connect the EMIU equipment to any other voltage.
6. All unused wires must be capped to prevent shorting.
7. The EMIU should be mounted securely and in locations and at heights where it will not be readily subjected to tampering by
unauthorized personnel.
8. The use of accessory equipment and replacement parts not recommended by manufacturer may cause an unsafe condition and will
void the warranty.
9. Do not mount near gas or electric heaters.
10. Do not let power supply cords touch hot surfaces.
11. Do not use this equipment for other than its intended use.
12. DO NOT USE OUTDOORS.
13. The EMIU uses sealed valve regulated lead acid batteries. Batteries can be punctured if not handled properly, therefore use caution
when servicing batteries. In the event battery acid comes in contact with eyes or skin, flush with fresh water and consult a physician
immediately.
MODEL NUMBER
EMIU1500 - 4 option
120/277 VAC, 60Hz
NOTE: At 120Vac, unit is rated at power factor 0.8. For loads having a power factor below 0.8, unit capacity needs to be derated.
At 277Vac, unit is rated at unity power factor. For loads having a power factor below 1, unit capacity needs to be derated.
All ABB inverter products receive 100% quality inspection before shipment to ensure proper and satisfactory operation.
When operated under normal conditions, ABB inverter products will provide years of dependable service.
For the complete warranty information, please refer to the landing page of our website (http://www.emergi-lite.com/usa/).
Tel: (888) 552-6467
EMIU 1500W - 4 Option Mini Inverter
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
AC SPECS
17.6 / 6.3 Amps
WARRANTY
Fax: (800) 316-4515
EMIU 1500W - 4 Option Mini Inverter
INTERRUPTIBLE EMERGENCY LIGHTING
UNIT INVERTER INSTRUCTION MANUAL
EMERGENCY POWER AVAILABLE FOR LOAD
90 MIN
2H
1500W
1136W
APPROX.
WEIGHT
3H
4H
789W
673W
395lbs.
11/22 750.2188 Rev. B
1/16

Advertisement

loading

Summary of Contents for ABB EMIU 1500W

  • Page 1 At 277Vac, unit is rated at unity power factor. For loads having a power factor below 1, unit capacity needs to be derated. WARRANTY All ABB inverter products receive 100% quality inspection before shipment to ensure proper and satisfactory operation. When operated under normal conditions, ABB inverter products will provide years of dependable service.
  • Page 2 EMIU 1500W - 4 Option Mini Inverter WARNING: DE-ENERGIZE THE CIRCUIT BEFORE INSTALLATION OR MAINTENANCE. WARNING: DO NOT ENERGIZE THE CIRCUIT UNTIL ALL STEPS HAVE BEEN SUCCESSFULLY COMPLETED. ALWAYS TURN OFF THE INVERTER MODULE AND THE AC SUPPLY TO THE EQUIPMENT AND DISCONNECT THE BATTERY BEFORE SERVICING.
  • Page 3: Installation

    EMIU 1500W - 4 Option Mini Inverter INSTALLATION STEP 1: MOUNTING THE MINI INVERTER TO WALL (SEE FIGURE 1) a. Remove the front cover of the Mini Inverter cabinets by removing the two screws located on the front of the cover of each cabinet and retain for later use.
  • Page 4 EMIU 1500W - 4 Option Mini Inverter ELECTRICAL SINGLE LINE DIAGRAM FOR EMIU 1500W WITH 4 CIRCUITS (-4 OPTION) Configuration:120Vin//120Vout OUTPUT Circuit #1: Normally-ON SWITCHED INPUT Circuit #2: Normally-OFF Circuit #4 Circuit #3 & 4: Switched Circuit #3 Circuit #2...
  • Page 5 EMIU 1500W - 4 Option Mini Inverter STEP 4: WIRING TO SWITCHED INPUT POWER SUPPLIED TO THE SWITCHED AND UNSWITCHED INPUTS MUST BE FED FROM THE SAME CAUTION: BRANCH CIRCUIT. The Mini Inverter model with -4 option, and each circuit within in it, can be configured for various modes of operation as described below.
  • Page 6 EMIU 1500W - 4 Option Mini Inverter STEP 6: START-UP WITH NO LOAD CONNECTED. a. Confirm load is not connected. b. Follow start-up procedure in Step 7. STEP 7: START-UP PROCEDURE a. Turn on switch located on right hand side of inverter module in the electronic cabinet. Emergency lights and indicator will not illuminate.
  • Page 7: Manual Test

    EMIU 1500W - 4 Option Mini Inverter ® NEXUS (OPTION) ® NO WIRING IS REQUIRED FOR THE NEXUS VERSION. See Nexus® addendums: 750.1532 and 750.1641 for more information and antenna installation. See Nexus®Pro addendums: 750.1641 and 750.2060 for antenna installation and important information before powering up unit.
  • Page 8 EMIU 1500W - 4 Option Mini Inverter NORMALLY-ON OPERATION All four(4) circuits configured to operate in Normally-On mode. For 277 V output: red wire must be removed from 120 V side of Important: terminal block and wired to 277 V side of terminal block.
  • Page 9 EMIU 1500W - 4 Option Mini Inverter NORMALLY-OFF OPERATION All four(4) circuits configured to operate in Normally-Off mode. For 277 V output: red wire must be removed from 120 V Important: side of the terminal block and wired to 277 V side of terminal block.
  • Page 10 EMIU 1500W - 4 Option Mini Inverter SWITCHED LOAD OPERATION All four(4) circuits controlled by switches. Utility Orange Orange input Neutral Black Black TB1 LOCATION Ground Hot(120V) Neutral UTILITY Neutral TO OBTAIN Ground TO OBTAIN CAP ALL 120Vac OUTPUT 277Vac OUTPUT...
  • Page 11 EMIU 1500W - 4 Option Mini Inverter COMBINATION OF NORMALLY-ON, NORMALLY-OFF AND SWITCHED LOAD OPERATION Circuit #1: Normally-ON Circuit #2: Normally-OFF Circuit #3 & 4: Switched Utility Orange Orange input Neutral Black Black TB1 LOCATION Ground Hot(120V) Neutral UTILITY Neutral...
  • Page 12: Features And Options

    EMIU 1500W - 4 Option Mini Inverter FEATURES AND OPTIONS SYSTEM OPERATION • The diagnostic/charger is a self-contained, fully automatic microcontroller-based system. • When installation is complete, only the battery connection is needed. AC power need not be energized. Unit goes directly into lockout mode and waits for AC power to be restored.
  • Page 13 EMIU 1500W - 4 Option Mini Inverter 4. LIGHTING LOAD TESTING The test is fully automatic. To ensure accurate data from a connected and functional lighting load: • The battery must be at or near full power. The program will delay data capture for a minimum of 48 hours following any discharge or reset.
  • Page 14 EMIU 1500W - 4 Option Mini Inverter Terminal block for Dry form “C” contact Terminal block location for dimming control Figure 12 2. Connect the Lighting Control signal cables from the external Lighting Dimming Control panel to the terminal blocks (left side of cabinet) identified by IN1, IN2, IN3 or IN4 in the Mini Inverter.
  • Page 15: Troubleshooting Guide

    EMIU 1500W - 4 Option Mini Inverter TROUBLESHOOTING GUIDE STATUS TROUBLESHOOTING GUIDE INDICATOR SYMPTOMS PROBLEM CORRECTIVE ACTION (LED) None, if unit is in Normally ON Lamp load is ON Unit is operating correctly. mode. None, if unit is in Normally OFF Lamp load is OFF Unit is operating correctly.
  • Page 16 EMIU 1500W - 4 Option Mini Inverter TROUBLESHOOTING GUIDE No battery installed in unit. Install battery following installation guide. Battery Disconnect Error The 12V battery sensing not Check if yellow wire is connected. If not, connect. Refer to figure 4.
  • Page 17: Important Safeguards

    At 277Vac, unit is rated at unity power factor. For loads having a power factor below 1, unit capacity needs to be derated. WARRANTY All ABB inverter products receive 100% quality inspection before shipment to ensure proper and satisfactory operation. When operated under normal conditions, ABB inverter products will provide years of dependable service.
  • Page 18 EMIU 1500W Mini Inverter WARNING: DE-ENERGIZE THE CIRCUIT BEFORE INSTALLATION OR MAINTENANCE. WARNING: DO NOT ENERGIZE THE CIRCUIT UNTIL ALL STEPS HAVE BEEN SUCCESSFULLY COMPLETED. ALWAYS TURN OFF THE INVERTER MODULE AND THE AC SUPPLY TO THE EQUIPMENT AND DISCONNECT THE BATTERY BEFORE SERVICING. ONLY QUALIFIED SERVICE TECHNICIANS WARNING: SHOULD SERVICE THIS EQUIPMENT.
  • Page 19 EMIU 1500W Mini Inverter INSTALLATION STEP 1: MOUNTING THE MINI INVERTER TO WALL (SEE FIGURE 1) a. Remove the front cover of the Mini Inverter cabinets by removing the two screws located on the front of the cover of each cabinet and retain for later use.
  • Page 20 EMIU 1500W Mini Inverter ELECTRICAL SINGLE LINE DIAGRAM FOR EMIU 1500W SINGLE CIRCUIT Configuration:120Vin//120Vout Circuit: Normally-ON OUTPUT SWITCHED INPUT Neutral(Wht) Mini Inverter comes pre-wired 277VAC(ORG) for 120V. For 277V connections 120VAC(BLK) remove red wire from Neutral(Wht) Transformer 120V terminal and wire UNSWITCHED to 277V terminal.
  • Page 21 EMIU 1500W Mini Inverter STEP 4: WIRING TO SWITCHED INPUT POWER SUPPLIED TO THE SWITCHED AND UNSWITCHED INPUTS MUST BE FED FROM THE SAME CAUTION: BRANCH CIRCUIT. The Mini Inverter can be configured for various modes of operation as described below.
  • Page 22 EMIU 1500W Mini Inverter STEP 7: START-UP PROCEDURE a. Turn on switch located on right hand side of inverter module in the electronic cabinet. Emergency lights and indicator will not illuminate. b. Energize AC main supply. Status Indicator on the left side of electronic cabinet will illuminate. For information on the Status Indicator, see Information Section: FEATURES AND OPTIONS.
  • Page 23 EMIU 1500W Mini Inverter SYSTEM RESET Resetting the system: Depending on the sequence of installation, some units may require a system reset. To reset, press and hold test switch on left side of unit for 6 seconds. MAINTENANCE BATTERY: The batteries supplied in this equipment are high quality maintenance-free Valve Regulated Lead Acid design.
  • Page 24 EMIU 1500W Mini Inverter NORMALLY-OFF OPERATION Circuit configured to operate in Normally-Off mode. UTILITY UNSWITCHED Utility (120V) Neutral Unswitched INPUT input Neutral UNSWITCHED Ground INPUT Configuration shown: 120V in // 120V out. For 277V in // 277V out, SWITCHED connect utility hot wire to 277V position...
  • Page 25 EMIU 1500W Mini Inverter FEATURES AND OPTIONS SYSTEM OPERATION • The diagnostic/charger is a self-contained, fully automatic microcontroller-based system. • When installation is complete, only the battery connection is needed. AC power need not be energized. Unit goes directly into lockout mode and waits for AC power to be restored.
  • Page 26 EMIU 1500W Mini Inverter 4. LIGHTING LOAD TESTING The test is fully automatic. To ensure accurate data from a connected and functional lighting load: • The battery must be at or near full power. The program will delay data capture for a minimum of 48 hours following any discharge or reset.
  • Page 27 EMIU 1500W Mini Inverter TROUBLESHOOTING GUIDE STATUS TROUBLESHOOTING GUIDE INDICATOR SYMPTOMS PROBLEM CORRECTIVE ACTION (LED) None, if unit is in Normally ON Lamp load is ON Unit is operating correctly. mode. None, if unit is in Normally OFF Lamp load is OFF Unit is operating correctly.
  • Page 28 Consult Customer Service for current warranty information. All information and specifications contained in these instructions are subject to change due to engineer design, errors and omissions. © 2022 ABB. All rights reserved. Tel: (888) 552-6467 Fax: (800) 316-4515 11/22 750.2189 Rev. B...
  • Page 29 ADDENDUM NORMALLY-ON OPERATION: All four(4) circuits configured to operate in Normally-On mode. For 277 V output: red wire must be removed from 120 V side of Important: terminal block and wired to 277 V side of terminal block. Orange Orange Switched input Black Black...
  • Page 30 ADDENDA FONCTIONNEMENT NORMALEMENT ALLUMÉ: Tous les quatre (4) circuits configurés pour fonctionner en mode normalement allumé. Pour la sortie 277 V: le fil rouge doit être enlevé du côté 120 V du Important: bornier et câblé au côté 277 V du bornier.