Related Manuals for Toro 21695
Summary of Contents for Toro 21695
- Page 1 Form No. 3451-795 Rev A eSuper Recycler™ eC53AST 53cm Lawn Mower Flex-Force Power System ® Model No. 21695—Serial No. 400000000 and Up *3451-795* Register at www.Toro.com. Original Instructions (EN)
- Page 2 It is designed to use Model No. Toro 60V lithium-ion battery packs. These battery packs are designed to be charged only by Toro 60V lithium-ion battery chargers. Using these products for Serial No. purposes other than their intended use could prove dangerous to you and bystanders.
-
Page 3: Safety Alert Symbol
Replace any damaged or unreadable labels. Use only the battery pack specified by Toro. Using other accessories and attachments may increase the risk of injury and fire. Plugging the battery charger into an outlet that... - Page 4 Charge the battery pack with only the battery Do not use a battery-operated lawn mower in charger specified by Toro. A charger suitable for rain. 1 type of battery pack may create a risk of fire when used with another battery pack.
- Page 5 Replace the battery pack with a genuine Sharpen a dull blade on both edges to maintain Toro battery pack only; using another type of balance. Clean the blade and ensure that it is battery pack may cause a fire or risk of injury.
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decaloemmarkt Manufacturer's Mark 1. This mark indicates that the blade is identified as a part from the original machine manufacturer. - Page 7 decal137-9461 137-9461 1. Battery charge status decal140-8492 140-8492 1. Keep away from open fire 4. Recycle the battery or flames. properly. 2. Do not expose to rain. 5. Contains lithium ions; do not dispose improperly. 3. Read the Operator’s Manual. decal144-6035 144-6035 1.
- Page 8 Setup Important: The battery pack is not fully charged when it is purchased. Before using the machine for the first time, refer to Charging the Battery Pack (page 19). Mounting the Battery Charger (Optional) Parts needed for this procedure: Mounting hardware (not included) Procedure If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of...
-
Page 9: Unfolding The Handle
Unfolding the Handle No Parts Required Procedure WARNING Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. • Do not damage the cable(s) when folding or unfolding the handle. • Ensure that the cable(s) are routed to the outside of the handle. •... -
Page 10: Installing The Blade-Control Bar
Installing the Blade-Control Bar No Parts Required Procedure g344378 Figure 5 Assembling the Grass Bag No Parts Required Procedure g334351 Figure 6... -
Page 11: Product Overview
Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety... -
Page 12: Before Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Installing the Battery Pack Important: Use the battery pack only in temperatures that are within the appropriate range; refer Specifications (page 11). Ensure that the vents on the battery are clear of any dust and debris. -
Page 13: Adjusting The Cutting Height
Adjusting the Cutting Height DANGER Adjusting the height-of-cut could bring your hands into contact with a moving blade and result in serious injury. • Shut off the motor, remove the battery, and wait for all moving parts to stop before adjusting the cutting height. -
Page 14: During Operation
During Operation Starting the Machine Ensure that the battery pack is installed in the machine; refer to Installing the Battery Pack (page 12). Note: If the battery-compartment lid does not close completely, the battery is not fully installed. Insert the electric-start button into the electric-start switch (A of Figure 12). -
Page 15: Adjusting The Blade Speed
Adjusting the Blade Speed This machine has 2 blade-speed settings: A • When set to the A position, the blade speed is adjusted automatically for greater efficiency; changes in cutting conditions are detected and the blade speed increases when necessary to maintain quality of cut. -
Page 16: Shutting Off The Machine
Shutting Off the Machine Release the blade-control bar (A of Figure 15). Remove the electric-start button from the electric-start switch (B of Figure 15). Remove the battery pack; refer to Removing the Battery Pack from the Machine (page 16). Note: Whenever you are not using the machine, remove the battery pack. -
Page 17: Bagging The Clippings
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. Note: By default this machine is equipped with an economy blade for improved runtime; it also includes an optional performance blade for improved bagging and performance. Before bagging, install the performance blade;... -
Page 18: Operating Tips
For best performance, install a new blade before the cutting season begins. Cutting Leaves • Replace the blade when necessary with a Toro replacement blade. • After cutting the lawn, ensure that half of the lawn shows through the cut leaf cover. You may need Cutting Grass to make more than a single pass over the leaves. -
Page 19: After Operation
After Operation To remove the battery pack, slide the battery backward out of the charger. Refer to the following table to interpret the LED Charging the Battery Pack indicator light on the battery charger. Indicator Indicates Important: The battery pack is not fully charged light when you purchase it. -
Page 20: Cleaning Under The Machine
Cleaning Under the Folding the Handle Machine WARNING Cleaning Under the Machine in the Folding or unfolding the handle improperly can damage the cables, causing an unsafe Operating Position operating condition. Service Interval: After each use • Do not damage the cable(s) when folding or unfolding the handle. -
Page 21: Storing The Machine In The Vertical-Stow Position
Storing the Machine in the Vertical-Stow Position During the mowing season or in the off-season, you can store your machine in the vertical position to minimize storage space. DANGER The vertical-stow position exposes the bottom of the machine. • Remove the battery pack and the electric-start button before moving the machine into the vertical-stow position. -
Page 22: Recommended Maintenance Schedule(S)
Maintenance Remove the electric-start button and battery pack from the machine before maintaining or cleaning the machine. Use only the manufacturer’s recommended replacement parts and accessories. Inspect and maintain the machine regularly. Have the machine repaired only by an Authorized Service Dealer. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure... -
Page 23: Adjusting The Self-Propel Drive
Adjusting the Self-Propel Drive For Self-Propel-Drive Models Only Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. Turn the adjustment nut counterclockwise to loosen the cable adjustment (Figure 26). g231390 Figure 25 g269307... - Page 24 If you are located outside of the US and Canada, please contact your authorized • Do not store the machine with the battery pack Toro distributor. installed. • Clean all foreign material from the product. • When not in use, store the machine, electric-start button, battery pack, and battery charger out of the reach of children.
-
Page 25: Troubleshooting
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Always remove the battery from the machine when troubleshooting, inspecting, maintaining, or cleaning the tool. Problem Possible Cause Corrective Action... - Page 26 Problem Possible Cause Corrective Action The machine is producing a beeping 1. The battery pack is not charged. 1. Remove the battery pack from the sound. machine and charge it. 2. The machine is in an unsafe position 2. Ensure that the machine is not at an for operation.
- Page 27 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.