Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
GR-DVX44EG/EK,DVX77EG/EK,DVX88EG
SPECIFICATIONS
For General
Power supply
: DC 11.0 V } (Using AC Adapter)
Power consumption
LCD monitor off, viewfinder on
: Approx. 4.4 W (GR-DVX88/DVX77), Approx. 4.0 W (GR-DVX44)
LCD monitor on, viewfinder off
: Approx. 5.2 W (GR-DVX88/DVX77), Approx. 4.8 W (GR-DVX44)
Dimensions (W x H x D)
: 51 mm x 120 mm x 97 mm
Weight
: Approx. 500 g (GR-DVX88/DVX77)
Operating temperature
: 0°C to 40°C
Operating humidity
: 35% to 80%
Storage temperature
: –20°C to 50°C
Pickup
: 1/4" CCD
Lens
: F 1.8, f = 3.6 mm to 36 mm, 10:1 power zoom lens
Filter diameter
: ø27 mm
LCD monitor
: 2.5" diagonally measured, LCD panel/TFT active matrix system
Viewfinder
: Electronic viewfinder with 0.44" colour LCD
Speaker
: Monaural
For Digital Video Camera
Format
: DV format (SD mode)
Signal format
: PAL standard
Recording/Playback format
: Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
Maximum recording time
: SP: 80 min.
(using 80 min. cassette)
For Digital Still Camera (GR-DVX88/DVX77 only)
Storage media
: SD Memory Card/MultiMediaCard
Compression system
: Still image : JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
: 2 modes (XGA: 1024 x 768 pixels/VGA: 640 x 480 pixels)
Picture quality
: 2 modes (FINE/STANDARD)
Approximate number of storable images
(with the provided memory card [8 MB], with Sound Effects pre-stored)
FINE
: 40 (VGA), 20 (XGA)
STANDARD
: 130 (VGA), 60 (XGA)
(with an optional memory card [16 MB])
FINE
: 100 (VGA), 40 (XGA)
STANDARD
: 290 (VGA), 140 (XGA)
(with an optional memory card [32 MB])
FINE
: 210 (VGA), 90 (XGA)
STANDARD
: 610 (VGA), 290 (XGA)
(with an optional memory card [64 MB])
FINE
: 430 (VGA), 190 (XGA)
STANDARD
: 1230 (VGA), 600 (XGA)
DIGITAL VIDEO CAMERA
Camcorder
DC 7.2 V } (Using battery pack)
(with the LCD monitor closed and the viewfinder pushed back in)
Approx. 470 g (GR-DVX44)
48 kHz 2-channel (16-bit)
LP: 12.5 mm/s
LP: 120 min.
This service manual is printed on 100% recycled paper.
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD.
For Connectors
AV
: 1 V (p-p), 75 Ω, analogue
Video output
Audio output
: 300 mV (rms), 1 kΩ, analogue, stereo
Headphone output
(GR-DVX88/DVX77 only)
: Stereo
DV
Input/output
(GR-DVX88 only)
: 4-pin, IEEE 1394 compliant
Output
(GR-DVX77/DVX44 only)
: 4-pin, IEEE 1394 compliant
AC adapter AP-V10EG
Power requirement
: AC 110 V to 240 V`, 50 Hz/60 Hz
Output
: DC 11 V } , 1 A
Dimensions (W x H x D)
: 59 mm x 31 mm x 84 mm
Weight
: Approx. 140 g (not including Power Cord)
For General
Dimensions (W x H x D)
: 52 mm x 22 mm x 73 mm
Weight
: Approx. 35 g
For Connectors
USB (GR-DVX88/DVX77 only)
: Type B
EDIT (GR-DVX88/DVX77 only)
: ø3.5 mm, 2-pole
S-Video
: Y : 1 V (p-p), 75 Ω, analogue
Output
C : 0.29 V (p-p), 75 Ω, analogue
JLIP (GR-DVX44 only)
: ø3.5 mm, 4-pole
PC (DIGITAL PHOTO)
(GR-DVX44 only)
: ø2.5 mm, 3-pole
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject
to change without notice.
Jack Box
No. 86617
April 2001
Advertisement
Table of Contents
Related Manuals for JVC GR-DVX44EG
Summary of Contents for JVC GR-DVX44EG
- Page 1 SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DVX44EG/EK,DVX77EG/EK,DVX88EG SPECIFICATIONS For Connectors Camcorder : 1 V (p-p), 75 Ω, analogue Video output For General Audio output : 300 mV (rms), 1 kΩ, analogue, stereo Power supply : DC 11.0 V } (Using AC Adapter) Headphone output DC 7.2 V } (Using battery pack)
-
Page 2: Table Of Contents
[GR-DVX77EG/EK, GR-DVX88EG] ........4-9 JACK BOARD ASSEMBLY <09> ..........5-24 4.5 PC IF SCHEMATIC DIAGRAM [GR-DVX44EG/EK] ... 4-11 W/B BOARD ASSEMBLY <11> ..........5-24 The following table lists the differing points between Models GR-DVX44EG/EK, GR-DVX77EG/EK and GR-DVX88EG in this series. GR-DVX44EG GR-DVX44EK GR-DVX77EG... -
Page 3: Important Safety Precautions
Important Safety Precautions Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. - Page 4 • Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
-
Page 6: Disassembly
SECTION 1 DISASSEMBLY 1.1 BEFORE ASSEMBLY AND DISASSEMBLY 1.1.4 Disconnection of Connectors (Wires) 1.1.1 Precautions Connector Pull both ends of the connector in the arrow direction, re- 1. Be sure to remove the power supply unit prior to mount- move the lock and disconnect the flat wire. ing and soldering of parts. -
Page 7: Jigs And Tools Required For Disassembly, Assembly And Adjustment
1.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, 1.3 DISASSEMBLY/ASSEMBLY OF CABINET PARTS ASSEMBLY AND ADJUSTMENT AND BOARD ASSEMBLY 1.2.1 Tools required for adjustments 1.3.1 Disassembly flow chart This flowchart indicates the disassembly step for the cabi- Torque Driver YTU94088 YTU94088-003 net parts and board assembly in order to gain access to item(s) to be serviced. -
Page 8: Disassembly Method
1.3.2 Disassembly method NOTE Beware of electrical shock due to the capacitor during work. STEP Fig.No. PART POINT NOTE (GR-DVX77EG/EK and GR-DVX88EG) DECK OPE ASSY Fig.1-3-1 2(S1), (L1) — NOTE a: When disassembling the Front Cover Assembly, remove CN 1a the screws, pull out the studs and free the grip belt. - Page 9 LOCK (MONITOR) NOTE NOTE NOTE NOTE Fig. 1-3-3 Fig. 1-3-1 NOTE : 0.118N·m (1.2kgf·cm) : 0.098N·m (1.0kgf·cm) NOTE GRIP BELT NOTE COVER STUD (DV) (HOOK) HOOK Fig. 1-3-2...
- Page 10 NOTE : 0.198N·m (2.0kgf·cm) Fig. 1-3-4 TAPE NOTE NOTE Fig. 1-3-5...
- Page 11 : 0.147N·m (1.5kgf·cm) NOTE NOTE NOTE NOTE Fig. 1-3-6 Fig. 1-3-7 NOTE NOTE SWITCH NOTE <TOP VIEW> NOTE NOTE NOTE NOTE CN803(AUDIO) : 0.098N·m (1.0kgf·cm) Fig. 1-3-8...
- Page 12 BRACKET (TOP) NOTE SWITCH SPACER NOTE : 0.098N·m (1.0kgf·cm) Fig. 1-3-9 NOTE BRACKET (MECHA) NOTE NOTE NOTE SHIELD PLATE NOTE Fig. 1-3-10...
-
Page 13: Disassembly Of 5 Monitor Assembly
1.4 DISASSEMBLY OF 5 MONITOR ASSEMBLY b: Remove the MONITOR board assembly and Note backlight together unless it is needed to separate 1.4.1 5 Monitor assembly/Hinge assembly them from each other for part replacement, etc., 1. Remove the four screws (1-4). While opening the moni- because the two are soldered to each other. -
Page 14: Disassembly Of 7 Op Block Assembly/Ccd Board Assembly
1.5 DISASSEMBLY OF 7 OP BLOCK ASSEMBLY/CCD 1.5.3 How to install OP block assembly and CCD board BOARD ASSEMBLY assembly 1.5.1 Precautions 1. Install the optical LPF with the space rubber fitted to its CCD side in the OP block assembly. 1. -
Page 15: Disassembly Of 9 E. Vf Assembly
1.6 DISASSEMBLY OF 9 E. VF ASSEMBLY 1.6.1 9E. VF assembly Note a: When disassembling the E VF assembly, remove <Frame (VF)> the frame (VF) from the case/cap assembly de- 5. Remove the screw (5) first and then LCD module/holder pending on the situation. -
Page 16: Emergency Display
1.7 EMERGENCY DISPLAY Whenever some abnormal signal is input to the syscon CPU, Example (in case of the error number E01): an error number (E01, as an example) is displayed on the LCD monitor or (in the electronic view finder). In every error status, such the message as shown below alternately appear over and over. -
Page 17: Service Note
1.8 SERVICE NOTE 1-12... -
Page 18: Mechanism Adjustment
SECTION 2 MECHANISM ADJUSTMENT 2.1 PRELIMINARY REMARKS ON ADJUSTMENT AND (3) The symbol (T or B)appearing in this column shows the REPAIR side which the objective part is mounted on. T =the upper side, B =the lower side 2.1.1 Precautions (4) Symbols appearing in this column indicate drawing 1. -
Page 19: Jigs And Tools Required For Disassembly, Assembly And Adjustment
2.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, ASSEMBLY AND ADJUSTMENT 2.2.1 Tools required for adjustments 1. Torque Driver Torque Driver YTU94088 YTU94088-003 Be sure to use to fastening the mechanism and exterior parts because those parts must strictly be controlled for tightening torque. -
Page 20: Disassembly/Assembly Of Mechanism Assembly
2.3 DISASSEMBLY/ASSEMBLY OF MECHANISM <SUB CAM GEAR> ASSEMBLY 2.3.1 General statement The mechanism should generally be disassembled/assem- bled in the EJECT mode (ASSEMBLY mode). (Refer to Fig. 2-3-1.) TOP VIEW BOTTOM VIEW However, when the mechanism is removed from the main body, it is set in the STOP mode. -
Page 21: Mechanism Timing Chart
2.3.3 Mechanism timing chart MODE EJECT C IN SHORT FF STOP PLAY PARTS MAIN CAM (ø10.4) 31.7 45.6 49.5 74.04 129.5 156.6 169.2 211.5 280.3 SUB CAM (ø11) 43.1 46.8 122.5 148.1 ENCODER (ø10) 47.4 51.5 134.7 162.9 291.5 ROTARY ENCODER CAM SW SLIDE END... -
Page 22: Disassembly/Assembly Of Mechanism Assembly
2.4 DISASSEMBLY/ASSEMBLY OF MECHANISM ASSEMBLY 2.4.1 Follow chart 1. Configuration Mechanism assembly Cassette housing assembly Slide deck assembly Main deck assembly Fig. 2-4-1 2. Procedures for disassembly Mechanism assembly Cassette housing assembly Slide deck assembly Main deck assembly Fig. 2-4-2... - Page 23 3. Disassembling procedure table PART NAME FIG. POINT NOTE REMARKS A Cassette housing assembly Fig. 2-4-5 3(S1),(L1a)-(L1d) 1a, 1b, 1c, 1d Adjustment Reel disk (SUP) assembly Fig. 2-4-6 (W2) 2a, 2b Reel disk (TU) assembly Fig. 2-4-6 (W2) 2a, 2b Reel cover assembly Fig.
- Page 24 < TOP VIEW > 4b 11b 11a Main deck assembly Slide deck assembly 7b 7a 7d 7e 9c 3c 3b 7h 2b Fig. 2-4-3 < BOTTOM VIEW > Main deck assembly Slide deck assembly Fig. 2-4-4...
-
Page 25: Disassembly/Assembly
2.4.2 Disassembly/assembly Note 1a: <STOP mode> Shift the mechanism mode 1. A Cassette housing assembly from the STOP mode to the EJECT mode. Cassette Note 1b: housing Reassemble the cassette (L1b) assembly housing assembly to the (S1) mechanism as the cancel lever is moved in the direc- tion of the arrow. - Page 26 3. 3a Tension arm assembly/ 3b Release guide assembly 3c Idler arm assembly/ 3d Guide arm assembly 3e Pinch roller arm assembly Note 3a: When removing the reel cover assembly, pay heed to re- lease guide assembly and guide arm assembly. For, the (W3a) guide arm assembly is just inserted into the slide deck as- sembly from the upside and it is apt to come off after the...
- Page 27 5. 5a Guide roller (S) assembly/ 5b Rail assembly Note 5a: When reassembling, insert the tip Guide roller of the guide roller with the coil (s) assembly spring put on it into the hole on the main deck. Tighten the guide roller by about 6 turns so that the Note 5a (P5)
- Page 28 Note 7a: 7. 7a Loading brake assembly/ 7b Guide pin (S) Don’t remove these parts unreasonably. If they are removed 7c Pad arm assembly/ 7d Slide guide plate assembly for some reason, be very careful not to lose them. 7e Collar/ 7f Collar/ 7g Sub brake assembly 7h Control plate assembly Note 7b: When reinstalling the sub brake assembly, set the control...
- Page 29 9. 9a Loading guide/ 9b Timing belt 9c Center gear assembly/ 9d Motor bracket assembly 9e Worm wheel/ 9f Gear holder Note 9a: Carefully handle the DEW sensor. (Don’t touch the sensor Note 9b Note 9a surface in particular.) Note 9b: When engaging the timing belt, make sure that it securely (S9) engages with the gears of both the center gear assembly and...
- Page 30 11. 11a Catcher (T) assembly/ 11b Capstan motor 11c Charge arm assembly/ 11d Sub cam gear 11e PWB holder Note 11: The following figure shows how to put the charge arm as- sembly and sub cam gear assembly together. (S11) (S11) Note 11 (W11)
-
Page 31: List Of Procedures For Disassembly
2.4.3 List of procedures for disassembly Cassette housing assembly (P5) (L1b) (S9) (W5a) (S9) (W5b) (W5a) (W3b) (S1) (W5a) (W10b) (L1d) (L1a) (S4) (S4) (S4) (S1) (L1c) (S1) (S11) (W10a) (S10) (S11) (S10) (W10a) (S11) (S9) (S11) (W9) (W4) (P4b) (P4a) (S9) (W7) -
Page 32: Checkup And Adjustment Of Mechanism Phase
2.5 CHECKUP AND ADJUSTMENT OF MECHANISM PHASE <Connect gear> (Note 2) Set the connect gear so <Rotary encoder> that its locating hole meets Set the “I” of the rotary the hole on the main deck part at the tapped hole assembly. -
Page 33: Mechanism Adjustments
2.6 MECHANISM ADJUSTMENTS 2.6.1 Assembling slide deck assembly and main deck assembly œ Œ Fig. 2-6-1 Assembling procedure 1. Loosen the screw A. 2. Set the mechanism in the PLAY mode. (Refer to “2.3.2 Explanation of mechanism mode”.) 3. Press the end face B of the slide deck assembly (reel disk side) and the end face C of the main deck assem- bly (drum assembly side) with uniform force so that the two assemblies are tightly pressed to each other. -
Page 34: Locating Tension Pole
2.6.2 Locating tension pole <PLAY mode> Fig. 2-6-2 Locating procedure 1. Enter the mechanism assembly into the PLAY mode. (Refer to “2.3.2 Explanation of mechanism mode”.) 2. When the “ ” part is positioned down, make sure that the part “a” of the tension arm assembly is located within the range of “b”. -
Page 35: Service Note
2.7 SERVICE NOTE Use the following chart to manage mechanism parts that are removed for disassembling the mechanism. Cassette housing assembly S1×3 Reel disk (SUP) assembly Reel cover assembly W2×1 Reel disk (TU) assembly S2a×2 S2b×1 W2×1 W2×1 Guide arm Tension arm Pinch roller arm Release guide... - Page 36 Slide deck assembly Loading Slide guide Guide pin Pad arm brake plate assembly assembly assembly W7×1 P7a×1 S7a×1 W7×1 P7b×1 S7b×1 Control Collar Collar Sub brake plate assembly assembly W7×1 P7c×1 W7×2 P7d×1 W6×1 Main deck assembly Slide lever Tension lever Brake control assembly assembly...
-
Page 37: Jig Connector Cable Connection
2.8 JIG CONNECTOR CABLE CONNECTION Remove one screw (1) first and the cover (JIG) next. GUIDE ROLLER (SUP) ASSY CN105 SHEET GUIDE ROLLER (TU) ASSY COVER (JIG) EXTENSION CONNECTOR NOTE) For supplying the power through the coupler by removing the cover (for jig), use this extension connector double for connecting the jig connector cable. -
Page 38: Electrical Adjustment
SECTION 3 ELECTRICAL ADJUSTMENT 3.1 PRECAUTION 3. Tools required for adjustments 1. Precaution Torque Driver Both the camera and deck sections of this model needs a YTU94088 YTU94088-003 personal computer for adjustment except simple adjustment with potentiometers. If some of the following parts is replaced for repair or other reason, the repaired set must be adjusted with a personal computer. -
Page 39: Setup
Torque driver PC cable Be sure to use to fastening the mechanism and exte- To be used to connect the VideoMovie and a personal rior parts because those parts must strictly be control- computer with each other when a personal computer led for tightening torque. -
Page 40: Charts And Diagrams
SECTION 4 CHARTS AND DIAGRAMS NOTES OF SCHEMATIC DIAGRAM 4. Voltage measurement CIRCUIT BOARD NOTES 1) Regulator (DC/DC CONV) circuits 1. Foil and Component sides Safety precautions REC : Colour bar signal. 1) Foil side (B side) : The Components identified by the symbol : Alignment tape (Colour bar). -
Page 41: Board Interconnections [Gr-Dvx44Eg/Ek]
BOARD INTERCONNECTIONS [GR-DVX44EG/EK] NOTE ) : The number of patch cords are indicated by interconnected. OPEN DECK OPE ASSY LCD MODULE (Page 4-69) JUNCTION (Page 4-48) (Page 4-57) (Page 4-65) V OUT TG/V.DRV YTU94074-24 YTU94074-20 YTU94077-24 YTU94077-20 (Page 4-33) A/HP SEL. - Page 42 BOARD INTERCONNECTIONS [GR-DVX77EG/EK , DVX88EG] NOTE ) : The number of patch cords are indicated by interconnected. DECK OPE ASSY LCD MODULE (Page 4-69) (VIDEO/DSC SW) JUNCTION (Page 4-48) (Page 4-57) (Page 4-65) V OUT YTU94074-24 TG/V.DRV YTU94074-20 YTU94077-24 YTU94077-20 (Page 4-33) A/HP SEL.
-
Page 43: Syscon Schematic Diagram [Gr-Dvx44Eg/Ek]
SYSCON SCHEMATIC DIAGRAM [GR-DVX44EG/EK] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. - Page 44 SYSCON SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( SYSCON ) TO REG SERVO...
-
Page 45: Pc If Schematic Diagram [Gr-Dvx44Eg/Ek]
PC IF SCHEMATIC DIAGRAM [GR-DVX44EG/EK] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. - Page 46 PC IF SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( PC IF ) C1301 TO SYSCON...
-
Page 47: Dvmain Schematic Diagram [Gr-Dvx44Eg/Ek]
NOTES : For the destination of each signal and further line connections that are cut off from DVMAIN SCHEMATIC DIAGRAM [GR-DVX44EG/EK] this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. - Page 48 DVMAIN SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( DVMAIN ) USED TO CAM DSP...
-
Page 49: Servo Schematic Diagram
TO REG y10199001a rev0 MODEL MODEL IC1402 R1417 R1443 R1435 R1443 R1444 R1402 MODEL ROMTYPE IC1401 IC1403 R1410 R1411 R1412 IC1401 GR-DVX44EG/EK YQ44887A GR-DVX44EG/EK TC7W66FU NONE NONE FLASH MN1030F04KYBJN TC7W53FU GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG YQ44888A GR-DVX77EG/EK , DVX88EG NONE NONE NONE... -
Page 50: Pre/Rec Schematic Diagram
4.10 PRE/REC SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. SERVO TO VF MAIN TO CAM DSP... -
Page 51: Out Schematic Diagram [Gr-Dvx44Eg/Ek]
For the destination of each signal and further line connections that are cut off from 4.11 V OUT SCHEMATIC DIAGRAM [GR-DVX44EG/EK] this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. -
Page 52: Out Schematic Diagram
V OUT SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] NOTES : For the destination of each signal and further line connections that are cut off from 4.12 this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO REG ( NC ) TO VF MAIN... -
Page 53: Cam Dsp Schematic Diagram [Gr-Dvx44Eg/Ek]
4.13 CAM DSP SCHEMATIC DIAGRAM [GR-DVX44EG/EK] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. - Page 54 CAM DSP SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] 4.14 MAIN ( CAM DSP ) TO TG/V.DRV TO VF MAIN TO SYSCON, VF MAIN TO DVMAIN TO SYSCON, DVMAIN TO DVMAIN TO CCD TO VF MAIN (NC) TO PRE/REC TO DVMAIN TO PRE/REC TO STO SENS TO VF MAIN TO SYSCON...
-
Page 55: Ana In Schematic Diagram [This Schematic Diagram Is Not Used]
4.15 ANA IN SCHEMATIC DIAGRAM [THIS SCHEMATIC DIAGRAM IS NOT USED] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. OPEN ( ANA IN ) TO CAM DSP... -
Page 56: Tg/V.drv Schematic Diagram
4.16 TG/V.DRV SCHEMAITC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( TG/V.DRV ) TO CCD TO CAM DSP... -
Page 57: Reg Schematic Diagram
STO SENS, VF MAIN, MP3, USB DRV TO SYSCON TO SYSCON TO SERVO TO VF MAIN TO TG/V.DRV TO VF MAIN TO SYSCON TO SYSCON TO SERVO NSW0018-001X TO VF MAIN y10202001a rev0 NO WEAR L6204 GR-DVX44EG/EK NSW0018-001X GR-DVX77EG/EK, DVX88EG 4-35 4-36... -
Page 58: Sto Sens Schematic Diagram
STO SENS SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] 4.18 NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( STO SENS ) TO STROBE CN6501... -
Page 59: Vf Main Schematic Diagram
TO PRE/REC TO DVMAIN TO SERVO TO SYSCON TO SYSCON TO SERVO TO SERVO CAM DSP TO REG SYSCON PC IF CN106 SERVO TO SYSCON y20140001a rev0 EXCHANGE PARTS LIST GR-DVX44EG/EK GR-DVX77EG/EK, DVX88EG TO IR TALLY CN206 NO WEAR 4-39 4-40... -
Page 60: Dsc Schematic Diagram
DSC SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] 4.20 NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( DSC ) TO REG TO DSC... -
Page 61: Mp3 Schematic Diagram [Gr-Dvx77Eg/Ek, Gr-Dvx88Eg]
4.21 MP3 SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO VF MAIN TO VF MAIN TO DSC... -
Page 62: Usb Drv Schematic Diagram
USB DRV SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] 4.22 NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( USB DRV ) TO DSC TO REG... -
Page 63: W/B Schematic Diagram
When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( W/B ) TO VF MAIN TO TG/V.DRV CN107 TO REG TO SYSCON TO CAM DSP CN107 TO TG/V.DRV CN107 y40073001a rev0 y40072001a rev0 GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG NO WEAR 4-47 4-48... -
Page 64: Mda Schematic Diagram
4.25 MDA SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MDA ( MDA ) TO IR TALLY IR TALLY... -
Page 65: Ir Tally Schematic Diagram
TO MDA RS-171-X TO CN206 MDA ( IR TALLY ) LOADING MOTOR TO MDA CN207 TO CN206 EXCHANGE PARTS LIST SUB OPE. UNIT GR-DVX44EG/EK GR-DVX77EG/EK, DVX88EG DRUM MOTOR ONLY USED FOR DVX77EG/EK DVX88EG TO CN206 CAPSTAN MOTOR TO JUNCTION CN601... -
Page 66: Op Driver Schematic Diagram
TO IR TALLY y30132001a rev0 NO WEAR EXCHANGE PARTS LIST R4837 , R4839 , R4840 R4841 , R4842 R4846 , R4849 IC4807 Q4802 Q4803 Q4804 Q4805 R4825 R4826 GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG TC7W66FU 2SC4617/RS/-X DTC144EE DTA144EE DTA143EE 2.2k 4-53 4-54... -
Page 67: Monitor Schematic Diagram
4.28 MONITOR SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MONITOR LCD MODULE TO VF MAIN... -
Page 68: Junction Schematic Diagram
When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO SPEAKER TO CARD CN766 TO IR TALLY CN208 CAMERA OPE. UNIT y30133001a rev0 NO WEAR GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG 4-57 4-58... -
Page 69: Strobe Schematic Diagram
STROBE SCHEMATIC DIAGRAM [GR-DVX77EG/EK , DVX88EG] 4.30 NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. NQS0042-001X STO SENS CN109... -
Page 70: Audio Ad/Da Schematic Diagram
( AUDIO AD/DA ) MAIN AUDIO TO VF MAIN CN101 CN801 TO VF MAIN CN101 CN801 TO MAIN AUDIO TO VF MAIN CN101 CN801 y30134001a rev0 NO WEAR EXCHANGE PARTS LIST GR-DVX44EG/EK GR-DVX77EG/EK, DVX88EG GR-DVX44EG/EK GR-DVX77EG/EK, DVX88EG R2158 3.3k 4-61 4-62... -
Page 71: Main Audio Schematic Diagram
HCK1 R2001 DECK OPE ASSY CN803 R2002 1.5k VF VDD KEY PLAY R2003 1.8k KEY STOP GR-DVX44EG/EK S8 with ANA. IN GR-DVX77EG/EK, DVX88EG GR-DVX44EG/EK S8 with ANA. IN GR-DVX77EG/EK, DVX88EG KEY FF R2004 CVF B KEW REW 2.7k CVF R... -
Page 72: A/Hp Sel. Schematic Diagram
TO VF MAIN CN101 CN801 MAIN AUDIO TO VF MAIN CN101 CN801 REG-6.5V REG-6.5V TO VF MAIN CN101 CN801 MAIN AUDIO NO WEAR y30135001a rev0 EXCHANGE PARTS LIST GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG GR-DVX44EG/EK GR-DVX77EG/EK , DVX88EG 4-65 4-66... -
Page 73: Jack Schematic Diagram
4.34 JACK SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO VF MAIN CN103 J901... -
Page 74: Wb Sens, Camera Ope. Unit, Deck Ope. Assy And Sub Ope. Unit Schematic Diagrams
4.35 WB SENS , CAMERA OPE. UNIT , DECK OPE. ASSY AND SUB OPE. UNIT SCHEMATIC DIAGRAMS NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". The schematic diagram is only for reference. -
Page 75: Main Circuit Board [Gr-Dvx44Eg/Ek]
4.36 MAIN CIRCUIT BOARD [GR-DVX44EG/EK] FOIL SIDE ( B ) MAIN PWB YB10318-01-02 4-71 4-72... - Page 76 COMPONENT PARTS LOCATION GUIDE MAIN [GR-DVX44EG/EK] REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION C3033 C4314 C6204 IC3501 Q6210 R1307 CAPACITOR C3034 C4315 C6205 IC3701 Q6211 R1308 C1001 C3035 C4316 C6206 IC4201 Q6212 R1401...
- Page 77 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION R3509 R6002 RA1010 R3510 R6003 RA1401 R3521 R6004 RA1402 R3522 R6005 RA1403 R3701 R6008 RA3001 R3702 R6009 RA4301 R3703 R6010 RA4302 R3706 R6011 RA4303 R3707 R6012 TESTPOINT R3708 R6013 R3712 R6014 R3713 R6015 R3714 R6016 OTHER R3715...
- Page 78 COMPONENT SIDE ( A ) CN110 MAIN PWB YB10318-01-02 CN102 CN104 CN103 CN107 4-75 4-76...
-
Page 79: Main Circuit Board [Gr-Dvx77Eg/Ek, Gr-Dvx88Eg]
4.37 MAIN CIRCUIT BOARD [GR-DVX77EG/EK , DVX88EG] FOIL SIDE ( B ) MAIN PWB YB10319-01-02 4-77 4-78... - Page 80 [GR-DVX77EG/EK , DVX88EG] COMPONENT PARTS LOCATION GUIDE MAIN REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION C3036 C3957 C5518 C8011 CN112 L3001 CAPACITOR C3037 C3958 C5519 C8012 L3002 DIODE C1001 C3038 C3959 C6001 C8013 L3003 C1002 D1001...
- Page 81 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION Q6001 R1071 R3049 R4322 R6220 R8042 RA8401 Q6002 R1072 R3050 R4323 R6221 R8043 RA8402 Q6003 R1073 R3052 R4324 R6223 R8044 RA8403 Q6004 R1074 R3053 R4325 R6224 R8045 RA8404 Q6201...
- Page 82 COMPONENT SIDE ( A ) MAIN PWB YB10319-01-02 4-81 4-82...
-
Page 83: Mda Circuit Board
4.38 MDA CIRCUIT BOARD COMPONENT SIDE ( A ) FOIL SIDE ( B ) MDA PWB MDA PWB YB10320-01-01 YB10320-01-01 CN204 COMPONENT PARTS LOCATION GUIDE REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION C4814 R1628 R4840 TL1619 CAPACITOR COIL... -
Page 84: Ccd And Junction Circuit Boards
4.39 CCD AND JUNCTION CIRCUIT BOARDS JUNCTION FOIL SIDE ( B ) JUNCTION PWB FOIL SIDE ( B ) YB10323-01-01 CCD PWB YB10322-01-01 JUNCTION PWB COMPONENT SIDE ( A ) COMPONENT SIDE ( A ) YB10323-01-01 CCD PWB YB10322-01-01 CN602 CN601 CN603 4-85... -
Page 85: Monitor Circuit Board
4.40 MONITOR CIRCUIT BOARD MONITOR PWB MONITOR PWB YB10321-01-01 YB10321-01-01 FOIL SIDE ( B ) COMPONENT SIDE ( A ) CAUTION HIGH VOLTAGE CN761 F7501 COMPONENT PARTS LOCATION GUIDE MONITOR REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C7603 C7616... -
Page 86: Audio Circuit Board
4.41 AUDIO CIRCUIT BOARD COMPONENT SIDE ( A ) FOIL SIDE ( B ) CN804 AUDIO PWB AUDIO PWB YB10320-01-01 YB10320-01-01 COMPONENT PARTS LOCATION GUIDE AUDIO REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C2210 C2605... -
Page 87: Strobe, W/B And Jack Circuit Boards
STROBE , W/B AND JACK CIRCUIT BOARDS 4.42 [GR-DVX77EG/EK , DVX88EG] STROBE JACK FOIL SIDE ( B ) COMPONENT SIDE ( A ) STROBE PWB STROBE PWB FOIL SIDE ( B ) YB10249-01-01 YB10249-01-01 JACK PWB YB10323-01-01 COMPONENT SIDE ( A ) FOIL SIDE ( B ) COMPONENT SIDE ( A ) JACK PWB... -
Page 88: Voltage Charts
4.43 VOLTAGE CHARTS <SYSCON> <SERVO> <PRE/REC> <V OUT> <REG> MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. - Page 89 <OP DRIVER> <MAIN AUDIO> MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO.
-
Page 90: Power System Block Diagram
4.44 POWER SYSTEM BLOCK DIAGRAM TG/V.DRV MAIN V OUT OP BLOCK CN107 CN5201 CN5202 REG 4.8V Q3701 CCD 12V CCD-6.5V CCD-6.5V Q3702 REG-6.5V IC5501 REG 3V CCD 12V CCD 12V CCD 12V CCD 12V BATT. TERMINAL F6101 M UNREG Q5001 V DC DRUM PWR CAP PWR... -
Page 91: Video System Block Diagram
4.45 VIDEO SYSTEM BLOCK DIAGRAM FOR ANALOG INPUT MODEL EXT V IN IC3901 MAIN VYIN EXT Y IN IC3951 (ANA IN) C OUT YIN(0 7) IC4302 DAC Y/DAC C CIN(0 3) IC4303 YOUT(0 7) DYO(0 (MEMORY) COUT(0 3) DYO(0 TPA +/-, TPB +/- J101 DV JACK IC4201... -
Page 92: Parts List
PACKING CASE,B LY32032-007A PACKING CASE,C,E LY32032-008A PACKING CASE,A LY20588-001A CUSHION LY30023-003A POLY BAG QPA02003006 POLY BAG,A,C,E YQM30061-3 POLY BAG,B,D MODEL MARK LYT0757-001A INST.BOOK(EN),B,D GR-DVX44EG LYT0757-002A INST.BOOK(GE),A,C,E GR-DVX44EK LYT0757-003A INST.BOOK(FR),A,C,E LYT0757-004A INST.BOOK(DU),A,C,E GR-DVX77EG LYT0757-005A INST.BOOK(SP),A,C,E GR-DVX77EK LYT0757-006A INST.BOOK(IT),A,C,E LYT0757-007A INST.BOOK(DA),A,C,E GR-DVX88EG LYT0757-008A INST.BOOK(FI),A,C,E... - Page 93 FINAL ASSEMBLY <M2> ELECTRONIC VIEWFINDER <M4> MECHANISM <M3> 154K 154M <02> 154N 154J MAIN 154L <01> 154H AUDIO <08> 154P JUNCTION 154B <06> 154C 154E 154C 154D 210A 154F RATING LABEL 220G 154A 220G 220G 154G <11> 220F 220C 251C OPTICAL BLOCK 251D 251G...
-
Page 94: Final Assembly
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... - Page 95 MECHANISM ASSEMBLY <M3> NOTE:The section marked in AA and BB indicate Classification Part No. Symbol in drawing lubrication and greasing areas. Grease KYODO-SH-P YTU94027...
-
Page 96: Mechanism Assembly
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 97: Electronic Viewfinder Assembly
ELECTRONIC VIEWFINDER ASSEMBLY <M4> 305B 305A 305B REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 98: Monitor Assembly
MONITOR ASSEMBLY <M5> 504E 504C 504C 504B 504D 504A MONITOR <04> REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 99: Electrical Parts List
ELECTRICAL PARTS LIST REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... - Page 100 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 101 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 102 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 103 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 104 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 105 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 106 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 107 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
-
Page 108: Mda Board Assembly <02
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 109: Ccd Board Assembly <03
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 110: Junction Board Assembly <06
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... -
Page 111: Audio Board Assembly <08
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -... - Page 112 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
-
Page 113: Jack Board Assembly <09
REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...