1. Manuals
  2. Brands
  3. NEC Manuals
  4. Projector
  5. PA1705UL-W
  6. Installation manual

NEC PA1705UL-W Installation Manual

Hide thumbs Also See for PA1705UL-W:
Table of Contents

Advertisement

Quick Links

Download this manual
Projector
PA1705UL-W/PA1705UL-B
PA1505UL-W/PA1505UL-B
Installation Manual
Model No.
NP-PA1705UL-W/NP-PA1705UL-B/NP-PA1505UL-W/NP-PA1505UL-B

Advertisement

Table of Contents
loading

Related Manuals for NEC PA1705UL-W

Summary of Contents for NEC PA1705UL-W

  • Page 1 Projector PA1705UL-W/PA1705UL-B PA1505UL-W/PA1505UL-B Installation Manual Model No. NP-PA1705UL-W/NP-PA1705UL-B/NP-PA1505UL-W/NP-PA1505UL-B...

  • Page 2: Table Of Contents

    Table of Contents Introduction .............................. iv Important Information ........................v 1. Check the product overview, supplied items and part names ........1 1-1. Introduction to the Projector ......................1 1-2. What’s in the Box? ..........................4 1-3. Part Names of the Projector ......................5 1-4.
  • Page 3 Table of Contents 4. Multi-Screen Projection ........................ 61 4-1. Things that can be done using multi-screen projection ............61 4-2. Using a single projector to project two types of videos at the same time [PIP/ PICTURE BY PICTURE] .......................... 62 4-3.
  • Page 4 Table of Contents 9. Appendix ............................161 9-1. Throw distance and screen size ....................161 9-2. Compatible Input Signal List ......................167 9-3. Specifications ............................ 170 9-4. Cabinet Dimensions ........................173 9-5. Pin assignments and signal names of main connectors ............ 174 9-6.

  • Page 5: Introduction

    Introduction Thank you for purchasing the NEC projector. This projector can be connected to computers, video devices, etc. to project images sharply onto a screen. Please read this manual carefully before using your projector. Read this manual if you have any doubts about operation or if you believe the projector may be faulty.

  • Page 6: Important Information

    Important Information About the symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well as damage to property. The symbols and their meanings are described below. Be sure to understand them thoroughly before reading this manual.
  • Page 7 Important Information Safety Cautions WARNING Projected light Projected light and the pictogram/label indicated on the cabinet • Do not look into the projector’s lens. Strong light that could damage your vision is projected when the projec- tor is operating. Laser energy exposure near aperture may cause burns. Be PROHIBITED especially careful when children are around.
  • Page 8 Label 1 Label 4 Laser explanatory label This product complies with EN 50689:2021 except using the lens Label 2 of NP55ZL and NP56ZL. Label Label FDA certification label FDA additional warning label Label 3 Label Lens replacement caution label PA1705UL-W/PA1705UL-B PA1505UL-W/PA1505UL-B...
  • Page 9 Important Information WARNING • This projector is classified as either IEC/EN 62471-5:2015 risk group 2 or risk group 3 depending on the lens unit. When classified as risk group 3, this projector is intended for professional use and must be installed by professional installer to ensure safety. See page xviii for risk groups.
  • Page 10 Important Information WARNING • Handle the power cord with care. Damaging the cord could lead to fire or electric shock. - Do not place heavy objects on the cord. HAZARDOUS - Do not place the cord under the projector. VOLTAGE - Do not cover the cord with a rug, etc.
  • Page 11 Important Information WARNING Installing suspended from the ceiling • Consult your dealer for installing the projector on the ceiling. Special skills are required for ceiling installation. DO NOT perform installation work by people other than installers. Doing so CAUTION may result in the projector falling and causing injury. •...
  • Page 12 Important Information WARNING Do not disassemble the projector. • Do not remove or open the projector’s cabinet. Also, do not modify the projector. There are high voltage areas in the projec- tor. It may cause fire, electric shock, or laser light leakage, resulting in serious DO NOT damage to your eyesight or burns.
  • Page 13 Important Information CAUTION Power cord Handling the power cord • The projector should be installed close to an easily accessible power outlet. • When connecting the power cord to the projector’s AC IN terminal, make sure the connector is fully and firmly inserted. Be sure to fix the power cord using REQUIRED the power cord stopper.
  • Page 14 Important Information CAUTION Installation Securing the lens unit with the fall prevention wire • If the projector is going to be suspended from a ceiling or another high place, secure the lens unit using the fall prevention wire (sold separately). If the lens unit is not secured, it may fall down if it comes lose.
  • Page 15 Important Information CAUTION Handling batteries Incorrect usage of batteries can result in leaks or bursting. • Use the specified batteries only. • Insert batteries matching the (+) and (–) signs on each battery to the (+) and PROHIBITED (–) signs of the battery compartment. •...
  • Page 16 Important Information CAUTION Moving the projector • When carrying the projector, remove the lens unit and carry it with at least two people. Attempting to move the projector alone could result in back pain or other injuries. PROHIBITED • When carrying the projector with the lens unit removed, do not touch the mounting area of the lens with your hands.
  • Page 17 • Outline of laser emitted from the built-in light module: - Wave length: 455 nm - Maximum power: 390 W (PA1705UL-W/PA1705UL-B), 346 W (PA1505UL-W/PA1505UL-B) Light Module • A light module containing multiple laser diodes is equipped in the product as the light source.
  • Page 18 Important Information Laser light radiation range The figure below shows the maximum radiation range of the laser light. Horizontal angle (unit: degree) Lens position Center (Refer- Lens unit Zoom Right most Left most ence value) Tele 47.6 36.4 47.6 NP51ZL Wide 53.0 41.8...
  • Page 19 Important Information Risk groups This projector is classified as either IEC/EN 62471-5:2015 risk group 2 or risk group 3 depending on the lens unit. Risk group 2 (RG2) WARNING As with any bright light source, do not stare into the beam, RG2 IEC/EN 62471-5:2015. Risk group 3 (RG3) WARNING RG3 PRODUCT OF IEC/EN 62471-5:2015...
  • Page 20 ① Lens model name or throw ratio The lens model name and throw ratio are listed in the image below. a: Lens model name b: Throw ratio ② Combining lens units and risk groups PA1705UL-W PA1505UL-W Lens model name Throw ratio PA1705UL-B...
  • Page 21 The below figure describes the radiation zone (hazard zone) of light emitted by the projector that is classified as Risk Group 3 (RG3) of IEC/EN 62471-5:2015. Overhead view Side view a: Screen / b: Hazard zone PA1705UL-W/PA1705UL-B PA1505UL-W/PA1505UL-B Hazard zone (m) Hazard zone (m) Lens...
  • Page 22 Important Information • About the precautionary zone By providing a precautionary zone or physical barriers, it is possible to prevent human eyes from entering the hazard zone. When the manager of the projector (operator) cannot prevent spectators from entering the hazard zone such as in public facilities, it is recommended to secure a space of 1 m or more from the haz- ard zone as “the precautionary zone”...
  • Page 23 Important Information • Installation example considering the precautionary zone ① Floor or desktop installation example ② Ceiling installation example a: Screen / b: Hazard zone / c: Precautionary zone / d: floor If it is expected that spectators will intrude into the hazard zone when CAUTION installed on the ceiling, it is necessary to prevent spectators from entering that area.
  • Page 24 Important Information ③ Example of downward projection installed on the ceiling a: Screen / b: Hazard zone / c: Precautionary zone / d: floor If the precautionary zone between the floor and the hazard zone can- CAUTION not be secured, it is necessary to prevent spectators from entering the area around the screen as shown in the figure on the right.
  • Page 25 Important Information CAUTION Please follow all safety precautions. Installing the projector • When planning the layout of the projector, make sure to follow the safety measures listed in the installation manual. • In order to avoid danger, either install the device within easy reach of a wall outlet or provide a device like a breaker to disconnect power to the projector in emergency.
  • Page 26 • The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Sharp NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equip- ment.
  • Page 27 Important Information (For Customers in U.K.) IMPORTANT • The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: “Earth” BLUE: “Neutral” BROWN: “Live” • As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: •...
  • Page 28 Important Information Disposing of your used product In the European Union EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes the projector or electrical accessory, such as a power cord.
  • Page 29 Important Information Notes on installation and maintenance Do not install or store in such places as those described below. • Locations that amplify vibrations and impacts If installed in places where the vibrations from power sources and the like are conveyed, or in vehicles or on vessels, etc.
  • Page 30 Important Information Cautions for ensuring the projector’s performance • If intense light like laser beams enters from the lens, it could lead to malfunction. • Consult your dealer before using in places where much cigarette smoke or dust is present. •...
  • Page 31 Install an appropriate metal that has enough strength to support the projector for controlling the installation angle. Model name of option cover NP13CV-W for PA1705UL-W/PA1505UL-W NP13CV-B for PA1705UL-B/PA1505UL-B Two covers are packaged with the option cover NP13CV-W and NP13CV-B. Option cover A: for attaching to the connection terminal...
  • Page 32 Important Information The drawings below show the installation angle required to attach the option cover A and B re- spectively. • Both option cover A and B may need to be attached depending on the installation position of the projector. •...
  • Page 33 Important Information Installation angles required to attach the option cover B Option cover B 90° 0°–85° Option cover B must be attached 180° 0° 170°–265° Option cover B must be attached 270° NOTE: • The drawings show the image of installation angle as a reference. They are slightly different from the actual one. xxxii...
  • Page 34 Important Information Clearance for Installing the Projector • When installing the projector, keep sufficient space around it, as described below. If not, the hot exhaust emitted from the projector may be taken back in. Also, make sure no wind from an air-conditioner hits the projector. The projector’s heat control system may detect an abnormality (temperature error) and automati- cally shut off the power.
  • Page 35 • Cinema Quality Picture logo, NaViSet, ProAssist, and Virtual Remote are trademarks or registered trademarks of Sharp NEC Display Solutions, Ltd. in Japan, in the United State and other countries. • PowerPoint is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

  • Page 36: Check The Product Overview, Supplied Items And Part Names

    High quality pictures using Cinema Quality Picture technology The device displays high-resolution pictures with its rich gradation expression capability and by improving the contrast in the picture boundary area using the development technology for digital cinema projectors and the unique NEC video processor for image processing. •...
  • Page 37 It is also possible to change the background logo of the projector. (→ page 190) Please visit our web site for downloading each software. URL: https://www.sharp-nec-displays.com/dl/en/index.html • CRESTRON ROOMVIEW and Extron XTP compatibility The projector supports CRESTRON ROOMVIEW and Extron XTP, allowing multiple devices con- nected in the network to be managed and controlled from a computer.
  • Page 38 1. Check the product overview, supplied items and part names • [LIGHT MODE] and “Carbon Meter” display Three [LIGHT MODE] options can be selected according to the purpose of use. [LIGHT ADJUST] can also be used to reduce output power and control energy consumption. The energy-saving effect from that time will be factored into the amount of reduced CO emissions and displayed in the confirmation message when turning the power off as well as the [INFO.] area in the on-...

  • Page 39: What's In The Box

    1. Check the product overview, supplied items and part names 1-2. What’s in the Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector. Projector Dust cap for lens (9NER0271)

  • Page 40: Part Names Of The Projector

    1. Check the product overview, supplied items and part names 1-3. Part Names of the Projector Front The lens is sold separately. The description below is for when the NP54ZL lens is mounted. 1. Exhaust vent 7. Lens Heated air is exhausted from here. Images are projected from here.
  • Page 41 1. Check the product overview, supplied items and part names Rear 1. Exhaust vent 6. Terminals Heated air is exhausted from here. Connect the cables for the various audio and video signals. 2. Intake vent 7. AC IN Terminal Takes in outside air to cool the unit. Connect the supplied power cord’s three- 3.
  • Page 42 1. Check the product overview, supplied items and part names Controls/Indicators 11 12 5. TEMP. Indicator (POWER) Button Indicates high temperatures around the Switches between projector’s power on and projector. standby. 6. INPUT Button When turning off the power (standby), pressing the button once will bring up a Selects the input signal.
  • Page 43 1. Check the product overview, supplied items and part names 11 12 9. ENTER Button Moves to the next menu when the on- screen menu is displayed. Confirms the item when the confirmation message is displayed. 10. EXIT Button Returns to the menu on the previous level when the on-screen menu is displayed.
  • Page 44 1. Check the product overview, supplied items and part names Terminal Panel Features 1. HDMI 1 IN Terminal (Type A) 6. AUDIO OUT Mini Jack (Stereo Mini) Connects to the output terminals of a com- Outputs the audio signal corresponding to puter, blu-ray player, etc.
  • Page 45 1. Check the product overview, supplied items and part names 10. REMOTE Terminal (Stereo Mini) Use this terminal for wired remote control of the projector. NOTE: • When a remote control cable is connected to the REMOTE terminal, infrared remote control operations cannot be performed.

  • Page 46: Part Names Of The Remote Control

    1. Check the product overview, supplied items and part names 1-4. Part Names of the Remote Control 1. Infrared Transmitter Remote control signals are sent via infrared signal. Point the remote control at the remote control receiver on the projector. 2.
  • Page 47 1. Check the product overview, supplied items and part names 9. ENTER Button Moves to the next menu when the on-screen menu is displayed. Confirms the item when the confirma- tion message is displayed. 10. FOCUS Button Opens the focus adjustment screen. Adjust the focus (of the lens) with the ◀...
  • Page 48 1. Check the product overview, supplied items and part names 17. Geometric. Button Displays [GEOMETRIC CORRECTION] from the on-screen menu. Use it to adjust distortions in projected images. 18. STATUS Button Displays [USAGE TIME] of [INFO.] from the on- screen menu. 19.
  • Page 49 1. Check the product overview, supplied items and part names 30. ID SET Button Used to set the control ID when performing indi- vidual operations on multiple projectors using the remote control. Also used to toggle the character keyboard when the character input screen is dis- played.
  • Page 50 1. Check the product overview, supplied items and part names Battery Installation 1. Press the catch and remove the battery cover. 2. Install new ones (AAA). Ensure that you have the batteries’ polarity (+/−) aligned correctly. 3. Slip the cover back over the batteries until it snaps into place.
  • Page 51 1. Check the product overview, supplied items and part names Operating Range for Wireless Remote Control a: 7 m/276" / b: 20 m/787" / c: Remote sensor on projector cabinet / d: Remote control • The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
  • Page 52 1. Check the product overview, supplied items and part names Using the Remote Control in Wired Operation Connect one end of the remote cable to the REMOTE terminal and the other end to the remote jack on the remote control. REMOTE a: Remote jack NOTE:...

  • Page 53: Projecting An Image (Basic Operation)

    2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. 2-1. Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 17) Step 2 •...

  • Page 54: Connecting Your Computer/Connecting The Power Cord

    2. Projecting an Image (Basic Operation) 2-2. Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. Connect a commercially available HDMI cable between the computer's HDMI output connector and the projector's HDMI 1 IN or HDMI 2 IN connector.
  • Page 55 2. Projecting an Image (Basic Operation) HDMI 1 IN HDMI 2 IN Make sure that the prongs are fully inserted into both the AC IN and the wall outlet. To wall outlet a: Power cord (supplied) / b: HDMI cable (not supplied) •...
  • Page 56 2. Projecting an Image (Basic Operation) Using the power cord stopper To prevent the power cord from accidently removing from the AC IN of the projector, use the power cord stopper. NOTE: • If you pull on the power supply cord while the connector is fixed, the main unit may fall down and be damaged ①...

  • Page 57: Turning On The Projector

    2. Projecting an Image (Basic Operation) 2-3. Turning on the Projector WARNING The projector produces a strong light. When turning on the power, operate from the side or rear of the projector (outside the hazard zone). Also, when turning on the power, make sure no one within the projection range is looking at the lens.
  • Page 58 2. Projecting an Image (Basic Operation) Performing Lens Calibration After mounting the separately available lens unit or replacing a lens unit, perform [LENS CALIBRATION] by holding to press ZOOM/L-CALIB. button on the cabinet over two seconds. Calibration corrects the adjustable zoom, shift, and focus range.
  • Page 59 2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the op- portunity to select one of the 30 menu languages. To select a menu language, follow these steps: 1.

  • Page 60: Selecting A Source

    2. Projecting an Image (Basic Operation) 2-4. Selecting a Source Selecting the computer or video source NOTE: • Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the INPUT button for 1 second or longer. The projector will search for the available input source and display it.
  • Page 61 2. Projecting an Image (Basic Operation) Selecting Default Source You can set a source as the default source so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2.

  • Page 62: Adjusting The Picture Size And Position

    2. Projecting an Image (Basic Operation) 2-5. Adjusting the Picture Size and Position Use the lens shift, the adjustable tilt foot, the zoom and the focus to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the projected image’s vertical and Adjusting the focus horizontal position...
  • Page 63 2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION • Perform the adjustment from behind or from the side of the projector. If adjustments are performed from the front, your eyes could be exposed to strong light and get injured. •...
  • Page 64 2. Projecting an Image (Basic Operation) NOTE: • If the lens is shifted to the maximum in the diagonal direction, the screen peripheral area will be dark or shaded. TIP: • The figure below shows the lens shift adjustment range (projection method: Desktop/Front) of the NP54ZL lens unit. See page for other lens units.
  • Page 65 2. Projecting an Image (Basic Operation) Focus Recommend to perform the focus adjustment after leaving the projector under the state the TEST PATTERN has been projected for over 30 minutes. Applicable lens: NP51ZL/NP52ZL/NP53ZL 1. Press the FOCUS button. The [LENS FOCUS] control screen will be dis- played on.
  • Page 66 2. Projecting an Image (Basic Operation) 3. Press ▼ button to select the [PERIPHERY] on the on-screen menu, and then press either ◀ or ▶ button to align the focus of screen peripheral area. 4. Repeat steps 2 and 3 until the entire projec- tion screen is in focus.
  • Page 67 2. Projecting an Image (Basic Operation) Zoom 1. Press ZOOM/L-CALIB. button. The [ZOOM] adjustment screen will be displayed on. In another way, press the ZOOM button on the remote control. Press ◀▶ buttons to adjust zoom.
  • Page 68 2. Projecting an Image (Basic Operation) Adjusting the Tilt Foot 1. Turn the left and right tilt foot to adjust. The tilt foot lengthen and shorten when turned. Turn one of the tilt foot to adjust the image so that it is level. •...

  • Page 69: Adjusting A Picture And Sound

    2. Projecting an Image (Basic Operation) 2-6. Adjusting a picture and sound Adjusting the picture Display the on-screen menu and adjust the picture. (→ page 96) Turning Up or Down Volume Sound level from the AUDIO OUT terminal can be adjusted. Important: •...

  • Page 70: Turning Off The Projector

    2. Projecting an Image (Basic Operation) 2-7. Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The [POWER OFF / ARE YOU SURE ? / CARBON SAVINGS-SESSION 0.000[g-CO2]] message will appear.

  • Page 71: After Use

    2. Projecting an Image (Basic Operation) 2-8. After Use 1. Unplug the power cord. ① Pull to an appropriate position while pushing down the knob of the power cord stopper. ② Press down the knob on the clamper to open the clamper and take out the power cord. a: Clamper / b: Knob (power cord stopper) / c: Knob (clamper) 2.

  • Page 72: Convenient Features

    3. Convenient Features 3-1. Turn off the light of the projector (SHUTTER) 1. Press the SHUTTER CLOSE ( ) button on the remote control. The light source will turn off temporarily. Press the SHUTTER OPEN ( ) button to allow the screen to become illuminated again.

  • Page 73: Enlarging A Picture

    3. Convenient Features 3-3. Enlarging a Picture You can enlarge the picture up to four times. NOTE: • Depending on an input signal, the maximum magnification may be less than four times, or the function may be restricted. 1. Press and hold the CTL button and then press VOL./D-ZOOM (+) button on the remote control to magnify the picture.

  • Page 74: Adjustment Of Luminance (Brightness) And Energy-Saving Effect

    3. Convenient Features 3-4. Adjustment of luminance (brightness) and energy-saving effect Three [REF. LIGHT MODE] options can be selected according to the purpose of use. Brightness can be adjusted and controlled to maintain a constant brightness after adjustment. Function Description Page name REF.
  • Page 75 3. Convenient Features Display the [LIGHT MODE] screen 1. Press LIGHT button on the remote control. When [STANDARD] is selected for [MODE] The [REF. LIGHT MODE] screen will be displayed. When [PROFESSIONAL] is selected for [MODE] The [LIGHT MODE] screen will be displayed. Perform [LIGHT ADJUST] An explanation is given here using the [REF.
  • Page 76 3. Convenient Features Change [REF. LIGHT MODE] 1. With the cursor adjusted to [REF. LIGHT MODE], press the ENTER button. The [REF. LIGHT MODE] selection screen will be displayed. 2. Use the ▼▲ buttons to make a selection, and press the ENTER button. The display will return to the [REF.
  • Page 77 3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This will display the energy-saving effect during the period of reduced projector light source as the amount of CO h emission reductions. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON SAVINGS] message shows the total amount of CO emission reduction from the time of shipment up to now.

  • Page 78: Correcting Horizontal And Vertical Keystone Distortion [Cornerstone]

    3. Convenient Features 3-5. Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] Use the [CORNERSTONE] feature to correct keystone (trapezoidal) distortion to make the top or bot- tom and the left or right side of the screen longer or shorter so that the projected image is rectangular. 1.
  • Page 79 3. Convenient Features 5. Select [CORNERSTONE] and press the ENTER. Go back to display the [GEOMETRIC CORRECTION] screen of the on-screen menu. 6. Press the ▼ button to align with the [CORNERSTONE] and then press the ENTER button. The drawing shows the upper left icon ( ) is selected. The screen will switch to the [CORNERSTONE] screen.
  • Page 80 3. Convenient Features 11. Use the ▲▼◀▶ button to select another icon which points in the direction. On the [CORNERSTONE] screen, select [EXIT] or press the EXIT button on the remote control. The confirmation screen is displayed. 12. Press the ◀ or ▶ button to highlight the [OK] and press the ENTER button. This completes the [CORNERSTONE] correction.

  • Page 81: Operation For The On-Screen Menu By A Commercially Available Usb Mouse

    3. Convenient Features 3-6. Operation for the On-Screen Menu by a commercially available USB mouse Once a commercially available USB mouse is connected to this projector, it enables to perform the operation for the on-screen menu and the geometric correction easily. NOTE: •...
  • Page 82 3. Convenient Features Geometric correction The USB mouse can be used for [CORNERSTONE] CORRECTION, [HORIZONTAL CORNER], [VERTI- CAL CORNER], and [WARP]. In this clause, the [CORNERSTONE] CORRECTION by an USB mouse is explained as an example. 1. While the adjustment screen of the [COR- NERSTONE] CORRECTION is displayed, right click on the projection screen.

  • Page 83: Preventing The Unauthorized Use Of The Projector [Security]

    3. Convenient Features 3-7. Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image.
  • Page 84 3. Convenient Features 7. Type in the same combination of ▲▼◀▶ buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The [SECURITY] function has been enabled. To turn on the projector when [SECURITY] is enabled: 1.
  • Page 85 3. Convenient Features To disable the [SECURITY] function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [CONTROL] → [SECURITY] and press the ENTER button. The [OFF]/[ON] menu will be displayed. 3. Select [OFF] and press the ENTER button. The [SECURITY KEYWORD] screen will be displayed.

  • Page 86: Controlling The Projector By Using An Http Browser

    3. Convenient Features 3-8. Controlling the Projector by Using an HTTP Browser Overview You can display the HTTP server screen of the projector by using a web browser and operating the projector with a computer or smartphone. Possible operations on the HTTP server screen •...
  • Page 87 3. Convenient Features 4. Start up the web browser and enter the address or URL in the input field. Specify the address or URL as “http://<IP Address of Projector>/index.html”. The HTTP server screen will be displayed. NOTE: • To use the projector in a network, consult with your network administrator about network settings. •...
  • Page 88 IP address of the projector has been set in the “HOSTS” file of the computer being used. Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network setting by specifying http://pj.nec.co.jp/index.html...

  • Page 89: Storing Changes For Lens Shift, Zoom, And Focus [Lens Memory]

    3. Convenient Features 3-9. Storing Changes for Lens Shift, Zoom, and Focus [LENS MEMORY] This function serves to store the adjusted values when using the [LENS SHIFT], [ZOOM], and [FO- CUS] functions of the projector. Adjusted values can be applied to the signal you selected. This will eliminate the need to adjust lens shift, focus, and zoom at the time of source selection.
  • Page 90 3. Convenient Features To store your adjusted values in [REF. LENS MEMORY]: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ENTER button. 3. Press the ▶ button to select [INSTALLATION(2)].
  • Page 91 3. Convenient Features 4. Press the ▼ button to select [REF. LENS MEMORY] and press the ENTER button. The [REF. LENS MEMORY] screen will be displayed. 5. Make sure [PROFILE] is highlighted, then press the ENTER button. The [PROFILE] selection screen appears. 6.
  • Page 92 3. Convenient Features 8. Press the ◀ button to select and [YES] and press the ENTER button. Select a [PROFILE] number and save the adjusted [LENS SHIFT], [ZOOM], and [FOCUS] values to it. 9. Press the MENU button. The menu will be closed. TIP: •...
  • Page 93 3. Convenient Features To call up your adjusted values from [REF. LENS MEMORY]: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ENTER button. 3. Press the ▶ button to select [INSTALLATION(2)]. 4.
  • Page 94 3. Convenient Features 5. Make sure [PROFILE] is highlighted, then press the ENTER button. The [PROFILE] selection screen appears. 6. Press the ▼/▲ buttons to select the [PROFILE] number, then press the ENTER button. Return to the [REF. LENS MEMORY] settings screen. 7.
  • Page 95 3. Convenient Features TIP: To call up the stored values from [LENS MEMORY]: 1. From the menu, select [ADJUST] → [LENS MEMORY] → [MOVE] and press the ENTER button. The confirmation screen will be displayed. 2. Press the ◀ button to select and [YES] and press the ENTER button. During projection, if the adjusted values for an input signal have been saved, the lens will shift.

  • Page 96: Multi-Screen Projection

    4. Multi-Screen Projection This projector can be used singly or arranged in multiple units for multi-screen projection. 4-1. Things that can be done using multi-screen projection Case 1. Using a single projector to project two types of videos [PIP/PICTURE BY PICTURE] Connection example and projection image In the case of [PICTURE BY PICTURE]...

  • Page 97: Using A Single Projector To Project Two Types Of Videos At The Same Time [Pip/Picture By Picture]

    4. Multi-Screen Projection 4-2. Using a single projector to project two types of videos at the same time [PIP/PICTURE BY PICTURE] The projector has a feature that allows you to view two different signals simultaneously. You have two modes: [PIP] mode and [PICTURE BY PICTURE] mode. The projection video in the first screen display is known as the main display while the projection video that is called out subsequently is known as the sub-display.
  • Page 98 4. Multi-Screen Projection Projecting two screens 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PIC- TURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2. Select [SUB INPUT] using the ▼/▲ buttons, and press the ENTER button. This displays the [SUB INPUT] screen.
  • Page 99 4. Multi-Screen Projection Switching the main display with the sub-display and vice versa 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PIC- TURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2.
  • Page 100 4. Multi-Screen Projection Restrictions • The following operations are enabled only for the main display. - Audio-visual adjustments - Video magnification / compression using the partial VOL./D-ZOOM (+)(−) buttons. However, magnification / compression is up to the positions set in [PICTURE BY PICTURE] → [BORDER] only.

  • Page 101: Line Up Multiple Projectors To Display A High Resolution Image In A Larger Screen [Tiling]

    4. Multi-Screen Projection 4-3. Line up multiple projectors to display a high resolution image in a larger screen [TILING] This section provides procedures for projecting an image with a resolution of 3840 × 2160 (4K UHD) by using four projectors. Preparation: •...
  • Page 102 4. Multi-Screen Projection Setting [TILING] 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PICTURE SETTING] → [MODE]. This displays the [MODE] screen. 2. Select [TILING] using the ▼/▲ buttons, and press the ENTER button. The display returns to the [PICTURE SETTING] screen.

  • Page 103: Adjust Boundaries Of A Projected Image [Edge Blending]

    4. Multi-Screen Projection 4-4. Adjust boundaries of a projected image [EDGE BLENDING] This projector is equipped with an “[EDGE BLENDING] Function” that makes the edges (boundaries) of the projection screen indistinguishable. NOTE: • Before performing the Edge Blending function, place the projector in the correct position so that the image becomes square in the appropriate size, and then make optical adjustments (lens shift, focus, and zoom).
  • Page 104 4. Multi-Screen Projection Setting the overlap of projection screens ① Enable [EDGE BLENDING]. 1. Press the MENU button. The menu will be displayed. 2. Select [DISPLAY] → [EDGE BLENDING]. The [EDGE BLENDING] screen will be displayed. Align the cursor with [MODE] and then press the ENTER button.
  • Page 105 4. Multi-Screen Projection 4. Select an appropriate item from [TOP], [BOTTOM], [LEFT], and [RIGHT] for an area of overlapped edges, and turn on [CONTROL]. [TOP]: [OFF] [TOP]: [OFF] [LEFT]: [OFF] [RIGHT]: [ON] [LEFT]: [ON] [RIGHT]: [OFF] [BOTTOM]: [ON] [BOTTOM]: [ON] [TOP]: [ON] [TOP]: [ON] [LEFT]: [OFF]...
  • Page 106 4. Multi-Screen Projection ② Adjust [POSITION] and [RANGE] to determine an area of overlapped edges of images projected from each projector. When [MARKER] is set to [ON], markers of four colors are displayed on the screen. The cyan and green markers represent the edges of the region where images overlap, the magenta and red markers represent the range of overlapping (region/width).
  • Page 107 4. Multi-Screen Projection Fit the edge of the overlapping area to the edge of the image with [POSITION], then adjust the overlapping area (width) with [RANGE]. In the case of the figure on the previous page, first set the cyan marker to the edge of the image on the left screen and the green marker to the edge of the image on the right screen.
  • Page 108 4. Multi-Screen Projection 2. Select one option among nine by ▲ or ▼. Black Level Adjustment This adjusts the black level of the overlapping area and the non-overlapping area of the multi-screen (EDGE BLENDING). Adjust the brightness level if you feel the difference is too large. NOTE: •...
  • Page 109 4. Multi-Screen Projection 2. Use the ◀, ▶, ▼ or ▲ button to select an item and use the ◀ or ▶ to adjust the black level. Do this for the other projector if necessary. TIP: • The number of black level division screens changes depending on the number of edge blending positions selected (top, bottom, right, left).
  • Page 110 4. Multi-Screen Projection Adjust using a computer or smartphone [EDGE BLENDING] can be easily done using a computer or smartphone connected to the projectors via a network. Connect to the HTTP server (→ page 56) and display the [EDGE BLENDING] tab. Screen for computer Screen for smartphone The [EDGE BLENDING] setting/adjustment items are displayed on one screen and can be operated...

  • Page 111: Using On-Screen Menu

    5. Using On-Screen Menu 5-1. Using the Menus NOTE: • The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: •...

  • Page 112: Menu Elements

    5. Using On-Screen Menu 5-2. Menu Elements Slide bar Solid triangle Operation Guide Source Highlight Radio button REF. LIGHT MODE symbol Menu mode Thermometer symbol Off Timer remaining time Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight Indicates the selected menu or item.
  • Page 113 5. Using On-Screen Menu Using the character input screen Highlight the item for text input and press the ENTER button to bring up the character input screen. a: Text box / b: Highlight / c: Operation Guide 1. Press the ▼▲◀▶ buttons to highlight a character and then press the ENTER button. The character will be entered.

  • Page 114: List Of Menu Items

    5. Using On-Screen Menu 5-3. List of Menu Items • Some menu items are not available depending on the input source. • [BASIC] menu items are indicated by shaded area. Menu Item Default Options INPUT HDMI1 HDMI2 HDBaseT ENTRY LIST TEST PATTERN ADJUST PICTURE...
  • Page 115 5. Using On-Screen Menu Menu Item Default Options ADJUST IMAGE OPTIONS HORIZONTAL VERTICAL BLANKING TOP, BOTTOM, LEFT, RIGHT OVERSCAN AUTO, 0[%], 5[%], 10[%] ASPECT RATIO AUTO (HDTV/SDTV) AUTO, NORMAL, 4:3, LETTERBOX, WIDE SCREEN, ZOOM, FULL AUTO (COMPUTER) AUTO, NORMAL, 4:3, 5:4, 16:9, 15:9, 16:10, FULL, NATIVE VIDEO NOISE REDUCTION...
  • Page 116 5. Using On-Screen Menu Menu Item Default Options DISPLAY EDGE BLENDING MODE OFF, ON MARKER OFF, ON CONTROL OFF, ON RANGE POSITION BOTTOM CONTROL OFF, ON RANGE POSITION LEFT CONTROL OFF, ON RANGE POSITION RIGHT CONTROL OFF, ON RANGE POSITION BLEND CURVE OFF, 1, 2, 3, 4, 5, 6, 7, 8, 9 BLACK LEVEL...
  • Page 117 5. Using On-Screen Menu Menu Item Default Options SETUP MENU(2) MENU ANGLE 0° 0°, 90°, 270° MENU POSITION CENTER TOP-LEFT, TOP-CENTER, TOP-RIGHT, CENTER-LEFT, CENTER, CENTER-RIGHT, BOTTOM-LEFT, BOTTOM-CENTER, BOTTOM-RIGHT INSTALLATION(1) ORIENTATION AUTO AUTO, DESKTOP FRONT, CEILING REAR, DESKTOP REAR, CEILING FRONT SCREEN SCREEN TYPE FREE...
  • Page 118 5. Using On-Screen Menu Menu Item Default Options SETUP CONTROL TOOLS ADMINISTRATOR MENU MODE ADVANCED ADVANCED, BASIC MODE NOT SAVE SETTING VALUES OFF, ON NEW PASSWORD CONFIRM PASSWORD PROGRAM ENABLE OFF, ON TIMER SETTINGS EDIT ACTIVE TIME FUNCTION ADVANCED SETTINGS REPEAT DATE AND TIME TIME ZONE SETTINGS...
  • Page 119 5. Using On-Screen Menu Menu Item Default Options SETUP NETWORK NETWORK SERVICES HTTP SERVER OFF, ON, AUTH. SETTINGS SERVICE PJLink NEW PASSWORD CONFIRM PASSWORD CLASS CLASS1, CLASS2 DESTINATION AMX BEACON OFF, ON CRESTRON ROOMVIEW OFF, ON CRESTRON CONTROL (ENABLE, CONTROLLER IP ADDRESS, IP ID) Extron XTP OFF, ON...
  • Page 120 5. Using On-Screen Menu Menu Item Default Options INFO. USAGE TIME LIGHT HOURS USED PROJECTOR HOURS USED TOTAL CARBON SAVINGS SOURCE(1) INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO. SOURCE(2) SIGNAL TYPE BIT DEPTH VIDEO LEVEL SAMPLING FREQUENCY SOURCE(3)
  • Page 121 5. Using On-Screen Menu Menu Item Default Options INFO. HDBaseT SIGNAL QUALITY OPERATION MODE LINK STATUS HDMI STATUS Art-Net(1) Art-Net(2) Ch10 Ch11 Ch12...

  • Page 122: Menu Descriptions & Functions [Input]

    5. Using On-Screen Menu 5-4. Menu Descriptions & Functions [INPUT] HDMI1 This projects the video of the device connected to the HDMI 1 IN terminal. HDMI2 This projects the video of the device connected to the HDMI 2 IN terminal. HDBaseT Projects the video of the device connected to the HDBaseT IN port.
  • Page 123 5. Using On-Screen Menu Using the Entry List When any source adjustments are made, the adjustments are automatically registered in the Entry List. The (adjustment values of ) registered signals can be loaded from the Entry List whenever necessary. However, only up to 100 patterns can be registered in the Entry List. When 100 patterns have been registered in the Entry List, an error message is then displayed and no additional patterns can be registered.
  • Page 124 5. Using On-Screen Menu Calling up a signal from the Entry List [ (LOAD)] 1. Press the ▲ or ▼ button to select a signal and press the ENTER button. Editing a signal from the Entry List [ (EDIT)] 1. Press the ▲ or ▼ button to select a signal you wish to edit. 2.
  • Page 125 5. Using On-Screen Menu Cutting a signal from the Entry List [ (CUT)] 1. Press the ▲ or ▼ button to select a signal you wish to delete. 2. Press the ◀, ▶, ▲, or ▼ button to select [ (CUT)] and press the ENTER button.

  • Page 126: Menu Descriptions & Functions [Adjust]

    5. Using On-Screen Menu 5-5. Menu Descriptions & Functions [ADJUST] [PICTURE] [MODE] This function allows you to determine how to save settings for [DETAIL SETTINGS] of [PRESET] for each input. STANDARD Saves settings for each item of [PRESET] (Preset 1 through 7) PROFESSIONAL Saves all the settings of [PICTURE] for each input.
  • Page 127 5. Using On-Screen Menu [DETAIL SETTINGS] [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA SETTING] and [COLOR TEM- PERATURE].
  • Page 128 5. Using On-Screen Menu Adjusting Brightness and Contrast [DYNAMIC CONTRAST] When set, the most optimal contrast ratio is adjusted according to the video. Dynamic contrast is disabled. MOTION IMAGE Most optimal settings for moving images. STILL IMAGE Most optimal settings for static images. Rapidly follows any changes in the video. NOTE: •...
  • Page 129 5. Using On-Screen Menu Adjusting White Balance [WHITE BALANCE] This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen; Brightness for each color (RGB) is used to adjust the black level of the screen. [COLOR CORRECTION] Corrects the color for all signals.
  • Page 130 5. Using On-Screen Menu [CONTRAST] Adjusts the intensity of the image according to the incoming signal. [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies the color level from +/−...
  • Page 131 5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. NOTE: • The adjustments for [HORIZONTAL] and [VERTICAL] will be stored in memory for the current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency, its adjustments will be called up and applied.
  • Page 132 5. Using On-Screen Menu Selecting Overscan Percentage [OVERSCAN] Select overscan percentage (Auto, 0%, 5% and 10%) for signal. Projected image Overscaned by 10% NOTE: • The [OVERSCAN] item is not available: - when [NATIVE] is selected for [ASPECT RATIO]. Selecting the Aspect Ratio [ASPECT RATIO] Use this function to select the screen’s lateral:longitudinal aspect ratio.
  • Page 133 5. Using On-Screen Menu Options Function NATIVE The projector displays the current image in its true resolution when the incoming signal has a lower or higher resolution than the projector’s native resolution. (→ page 182) When the incoming signal has a higher resolution than the projector’s native resolution, the center of an image will be displayed.
  • Page 134 5. Using On-Screen Menu [VIDEO] Using Noise Reduction [NOISE REDUCTION] When projecting a video image, you can use the [NOISE REDUCTION] function to reduce the screen noise (roughness and distortion). Depending on the noise level, the noise reduction effect can be set to [OFF], [LOW], [MEDIUM] or [HIGH].
  • Page 135 5. Using On-Screen Menu [HDR MODE] AUTO Automatically distinguishes HDR signal. Projects the image based on the input signal Projects the image conforming to the HDR signal NOTE: • These options are available exclusively for 4K signal. Using the Lens Memory Function [LENS MEMORY] This function serves to store the adjusted values for each input signal when using the [LENS SHIFT], [ZOOM], and [FOCUS] functions of the projector.
  • Page 136 5. Using On-Screen Menu To store your adjusted values in [LENS MEMORY]: 1. Project the connected device signal you want to adjust. 2. Adjust the projecting image of position, size and focus by the SHIFT/HOME POSITION, ZOOM +/−, and FOCUS +/− buttons. •...
  • Page 137 5. Using On-Screen Menu To automatically apply the adjusted values at the time of source selection: 1. From the menu, select [LOAD BY SIGNAL] and press the ENTER button. 2. Press the ▼ button to select and [ON] and press the ENTER button. This will move the lens automatically to the position at the time of source selection according to the adjusted values.

  • Page 138: Menu Descriptions & Functions [Display]

    5. Using On-Screen Menu 5-6. Menu Descriptions & Functions [DISPLAY] [PIP/PICTURE BY PICTURE] SUB INPUT Select the input signal to be displayed in the sub-display. Please refer to “Using a single projector to project two types of videos at the same time [PIP/PICTURE BY PICTURE]”...
  • Page 139 5. Using On-Screen Menu BORDER Select the display boundary of the main display and sub-display of the [PICTURE BY PICTURE] screen. Sub-display Main display Sub-display Main display Main display Sub-display Display boundary TIP: • Seven options from zero to six are available. [GEOMETRIC CORRECTION] MODE Set pattern for correcting distortion.
  • Page 140 5. Using On-Screen Menu THROW RATIO Adjusts according to the projection ratio of the optional lens used. Lens unit Adjustment range NP51ZL 5 - 7 NP52ZL 6 - 9 NP53ZL 8 - 13 NP54ZL 12 - 21 NP55ZL 19 - 40 NP56ZL 39 - 75 * Adjustment ranges for NP51ZL, NP52ZL, and NP56ZL are provisional values.
  • Page 141 5. Using On-Screen Menu CORNERSTONE Display the 4-point correction screen and adjust the trapezoidal distortion of the projection screen. Please refer to “Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]” (→ page 45) for details on the operation. HORIZONTAL CORNER/VERTICAL CORNER Distortion correction for corner projection such as wall surfaces.
  • Page 142 5. Using On-Screen Menu 3. Press the ▼▲◀▶ buttons to adjust the corners or sides of the screen and then press the ENTER button. • The adjustment point will go back to being a cursor (yellow box). Explanation of screen transition •...
  • Page 143 5. Using On-Screen Menu [Adjustment points of the [VERTICAL CORNER] screen and movement points of the projec- tion screen] Point d will be displaced in a parallel manner at the same time as Points a, d, f Point e will be displaced in a parallel manner at the same time as Points f, g, h 4.
  • Page 144 5. Using On-Screen Menu Adjustment method 1. Align the cursor with the [WARP] of the [GEOMETRIC CORRECTION] menu and the press the ENTER. • Adjustment screen will be displayed on. 2. Press the ▼▲◀▶ buttons to align the cursor (blue box) with the target adjustment point and then press the ENTER.
  • Page 145 5. Using On-Screen Menu PC TOOL Recall the geometric correction data that is registered in the projector beforehand. Three types of correction data can be registered. In addition, recall the geometric correction data that is registered in the projector after adjusting with the ProAssist software application.
  • Page 146 5. Using On-Screen Menu [EDGE BLENDING] This adjusts the edges (boundaries) of the projection screen when projecting high resolution videos using a combination of several projectors in the up, down, left and right positions. MODE This enables or disables the [EDGE BLENDING] function. When [MODE] is set to [ON], the [MARKER], [TOP], [BOTTOM], [LEFT], [RIGHT], [BLACK LEVEL], and [BLEND CURVE] settings can be adjusted.
  • Page 147 5. Using On-Screen Menu [PICTURE SETTING] This sets the division conditions for reducing or enlarging the image area and displaying it in the desired position or for projecting using a combination of several projectors. Please refer to “Multi-Screen Projection” (→ page 66) for details. MODE Use the projector in a standalone state.
  • Page 148 5. Using On-Screen Menu Conditions for using tiling • All the projectors need to fulfil the following conditions. - The panel size must be the same - The projection screen size must be the same - The left and right ends or top and bottom ends of the projection screen must be consistent. - The settings for the [LEFT] and [RIGHT] of the [EDGE BLENDING] are the same - The settings for the [TOP] and [BOTTOM] of the [EDGE BLENDING] are the same If the tiling conditions are satisfied, the video screen of the projector at each installation position...

  • Page 149: Menu Descriptions & Functions [Setup]

    5. Using On-Screen Menu 5-7. Menu Descriptions & Functions [SETUP] [MENU(1)] Selecting Menu Language [LANGUAGE] You can choose one of 30 languages for on-screen instructions. NOTE: • Your setting will not be affected even when [RESET] is done from the menu. Selecting Menu Color [COLOR SELECT] You can choose between two options for menu color: [COLOR] and [MONOCHROME].
  • Page 150 5. Using On-Screen Menu [MENU(2)] [MENU ANGLE] Select the direction for displaying the menu. [MENU POSITION] Shift the menu displaying position. You can choose from 9 locations. TIP: • The display position of the menu is saved even when the power supply of the projector is turned off. •...
  • Page 151 5. Using On-Screen Menu DESKTOP REAR CEILING FRONT TIP: • Check whether the automatic [DESKTOP FRONT] is installed within ± 10 degrees for floor installation and whether the [CEILING FRONT] is within ±10 degrees for ceiling installation. Select manually when the projection screen is inverted. Selecting Aspect Ratio and Position for Screen [SCREEN] [SCREEN TYPE] Sets the aspect ratio of the projection screen.
  • Page 152 5. Using On-Screen Menu Using the Wall Color Correction [WALL COLOR] This function allows for quick adaptive color correction in applications where the screen material is not white. NOTE: • Selecting [WHITEBOARD] reduces light source brightness. [REF. LIGHT MODE] Three [REF. LIGHT MODE] options can be selected according to the purpose of use. You can also adjust output power and change luminance (brightness).
  • Page 153 5. Using On-Screen Menu TIP: • Brightness normally decreases with use, but by selecting [CONSTANT BRIGHTNESS] mode, sensors inside the projector detect brightness and automatically adjust the output, thereby maintaining a constant brightness throughout the life of the light module. However, if output is already at its maximum, brightness will decrease with use.
  • Page 154 5. Using On-Screen Menu [INSTALLATION(2)] [SHUTTER SETTINGS] Enabling and disabling the lens shutter function. POWER ON SHUTTER OPEN When the power is turned on, the light source comes on and the picture is projected. CLOSE The light source does not come on when the power is turned on. When the SHUTTER button is pressed, the shutter is released and the light source is turned on.
  • Page 155 5. Using On-Screen Menu [LENS POSITION] Set back the lens to the home position. [LENS CALIBRATION] The adjustment range of the zoom, focus, and shift of the mounted lens is calibrated. Be sure to carry out [LENS CALIBRATION] after replacing the lens. [LENS MOVE AMOUNT] Select one of five options to set the level of adjustment when the ◀/▶buttons are pressed briefly while the focus and zoom adjustment screens are displayed.
  • Page 156 5. Using On-Screen Menu [CONTROL] TOOLS ADMINISTRATOR MODE This allows you to select [MENU MODE], save settings, and set a password for the administrator mode. MENU MODE Select either [BASIC] or [ADVANCED] menu. — (→ page 83) NOT SAVE SETTING VALUES Placing a check mark will not save your projector settings.
  • Page 157 5. Using On-Screen Menu 2. Select a blank program number and press the ENTER button. The [ (EDIT)] screen will be displayed. 3. Make settings for each item as required. ACTIVE Place a check mark to enable the program. Select days of the week for the program timer. To execute the program from Monday to Friday, select [MON-FRI].
  • Page 158 5. Using On-Screen Menu 5. Select [ (BACK)] and press the ENTER button. You will be returned to the [PROGRAM TIMER] screen. 6. Select [EXIT] and press the ENTER button. You will be returned to the [TOOLS] screen. NOTE: • Up to 30 different timer settings can be programmed. •...
  • Page 159 5. Using On-Screen Menu Editing the programmed settings 1. On the [PROGRAM LIST] screen, select a program you want to edit and press the ENTER button. 2. Change the settings on the [EDIT] screen. 3. Select [OK] and press the ENTER button. The programmed settings will be changed.
  • Page 160 5. Using On-Screen Menu DATE AND TIME SETTINGS You can set the current time, month, date, and year. NOTE: • The projector has a built-in clock. The clock will keep working for about a month after the main power is turned off. If the main power is off for a month or more, the built-in clock will cease.
  • Page 161 5. Using On-Screen Menu Enabling Security [SECURITY] This feature turns on or off the [SECURITY] function. Unless the correct keyword is entered, the projector cannot project an image. (→ page 50) NOTE: • Your setting will not be affected even when [RESET] is done from the menu. Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the communication speed for the PC Control port (D-Sub 9P).
  • Page 162 5. Using On-Screen Menu Assigning or Changing the Control ID 1. Turn on the projector. 2. Press the ID SET button on the remote control. The [CONTROL ID] screen will be displayed. If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed.
  • Page 163 5. Using On-Screen Menu Turning On or Off Remote Sensor [REMOTE SENSOR] This option determines which remote sensor on the projector is enabled in wireless mode. The options are: [FRONT/BACK], [FRONT], [BACK], and [HDBaseT]. NOTE: • The remote control of the projector will not be able to receive signals if the power supply of the HDBaseT transmission device connected to the projector is switched on when this has been set to [HDBaseT].
  • Page 164 5. Using On-Screen Menu [NETWORK SETTINGS] Configure the various settings when using the projector connected to a network. Important: • Consult with your network administrator about these settings. • When using a wired LAN, connect the LAN cable to the LAN port on the projector. (→ page 168) •...
  • Page 165 5. Using On-Screen Menu WIRED LAN When you select [WIRED LAN] in the on-screen menu for the first time after purchasing the projector, the [NETWORK PASSWORD] setting screen will appear. Carry out the following Step (1) or Step (2). (1) When setting the network password (recommended) Refer to [NETWORK PASSWORD] (→...
  • Page 166 5. Using On-Screen Menu PROJECTOR NAME PROJECTOR NAME Set a unique projector name. Up to 16 alphanumeric characters and symbols DOMAIN Set a host name and domain name of the projector. HOST NAME Set a host name of the projector. Up to 16 alphanumeric characters DOMAIN NAME...
  • Page 167 5. Using On-Screen Menu ALERT MAIL ALERT MAIL This option will notify your computer of error messages via e-mail when — using wireless or wired LAN. Placing a checkmark will turn on the Alert Mail feature. Clearing a checkmark will turn off the Alert Mail feature. Sample of a message to be sent from the projector: Subject: [Projector] Projector Information THE COOLING FAN HAS STOPPED.
  • Page 168 5. Using On-Screen Menu [SERVICES] — HTTP SERVER Configure the settings for connecting to the HTTP server. Connect directly to the HTTP server without displaying the login screen. It is not possible to connect to the HTTP server. AUTH. Display the login screen when connecting to the HTTP server. Enter the USER NAME and PASSWORD that have been set at [ACCOUNT].
  • Page 169 • This function is for future expansion. Security can be improved by using together with an application compatible with the authentication function. For specifications related to the authentication procedure required by the application software, please visit our web site. https://www.sharp-nec-displays.com/dl/en/pj_manual/lineup.html Art-Net Art-Net is a communication protocol for transmitting and receiving DMX512 —...
  • Page 170 5. Using On-Screen Menu [ACCOUNT] You can register three types of accounts: [USER1], [USER2], and [USER3]. When [PASSCODE] is set, [REGISTER] is enabled for each user. [CHANGE USER NAME], [CHANGE PASSWORD], [ENABLE], and [DELETE] can be selected once the account has been registered at [REGISTER]. REGISTER Set the user name and password of the account for use with [HTTP Up to 16 alphanumeric...
  • Page 171 5. Using On-Screen Menu [SOURCE OPTIONS] Selecting Default Source [DEFAULT INPUT SELECT] You can set the projector to default to any one of its inputs each time the projector is turned on. LAST Sets the projector to default to the previous or last active input each time the projector is turned on. Searches for an active source in order of HDMI1 →...
  • Page 172 5. Using On-Screen Menu [EDID VERSION] Switch the EDID version for the HDMI 1 IN and HDMI 2 IN terminals. MODE1 Supports general signal MODE2 Supports 4K signal Select this mode for displaying 4K image using the device supporting 4K NOTE: •...
  • Page 173 5. Using On-Screen Menu [POWER OPTIONS] [POWER-SAVING] Select the standby mode: This setting is to keep the standby power consumption to the minimum necessary. The standby state changes automatically depending on the projector settings and the state and duration of connected devices (→ page 191). The consumption power also changes according to the standby state.
  • Page 174 5. Using On-Screen Menu Turning On the Projector by Detecting Input Signal [AUTO POWER ON SELECT] Under the state of standby or sleep, the projector automatically detects and projects synchroniz- ing signal input from the selected terminals among [HDMI1], [HDMI2], [HDBaseT] and [SDI] by this function.
  • Page 175 5. Using On-Screen Menu Returning to Factory Default [RESET] The [RESET] feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels. The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS], [ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].

  • Page 176: Menu Descriptions & Functions [Info.]

    5. Using On-Screen Menu 5-8. Menu Descriptions & Functions [INFO.] [USAGE TIME] LIGHT HOURS USED (H) PROJECTOR HOURS USED (H) TOTAL CARBON SAVINGS [kg-CO2] • The value of [LIGHT HOURS USED] reflects the temperature of the operating environment and the [LIGHT MODE] setting in the actual operating time. •...
  • Page 177 5. Using On-Screen Menu [VERSION] SOFTWARE [OTHERS] DATE TIME PROJECTOR NAME MODEL NO. SERIAL NUMBER CONTROL ID* LENS ID * [CONTROL ID] will be displayed when [CONTROL ID] has been set up. [CONDITIONS] INTAKE TEMPERATURE EXHAUST TEMPERATURE ATMOSPHERIC PRESSURE INSTALLATION POSITION X-AXIS Y-AXIS Z-AXIS...
  • Page 178 5. Using On-Screen Menu About [OPTION COVER] This is used to check whether the option cover (separately sold) needs to be attached when the projector is installed at an angle. - / - Option cover is not required A / - Only option cover A needs to be attached - / B Only option cover B needs to be attached...

  • Page 179: Attachment/Detachment Of Parts Sold Separately

    6. Attachment/detachment of parts sold separately 6-1. Lens unit Six separate bayonet style lenses can be used with this projector. The descriptions here are for the NP54ZL lens. Mount other lenses in the same manner. • After installing or replacing the lens unit, press the ZOOM/L-CALIB. button on the projector to carry out [LENS CALIBRATION]. By carrying out [LENS CALIBRATION], the adjustment range of the lens shift is calibrated.
  • Page 180 6. Attachment/detachment of parts sold separately 2. Remove the lens cap on the back of the lens. NOTE: • Make sure to remove the lens cap at the unit back side. If the lens unit with the lens cap remaining on is installed on the projector, it may cause of malfunction.
  • Page 181 6. Attachment/detachment of parts sold separately 5. With the plate on the lens unit facing up, insert the lens unit into the projector's lens hole. Align the position of the connector and gently insert it as far back as possible. c: Plate / d: Connector 6.
  • Page 182 6. Attachment/detachment of parts sold separately Removing Preparations: 1. Turn on the projector and display an image. 2. Press and hold the SHIFT/HOME POSITION button over 2 seconds. The lens position will be moved to the home position. 3. Turn off the main power switch, and then unplug the power cord. 4.
  • Page 183 6. Attachment/detachment of parts sold separately 3. Gently pull the lens unit out from the pro- jector. Once the lens unit has been removed, attach the rear lens cap included with the lens unit before storing. 4. Attach the lens cover to the projector. (1) Leave a gap of about 2 cm when attaching the lens cover.

  • Page 184: Option Cover

    6. Attachment/detachment of parts sold separately 6-2. Option cover Model name of option cover NP13CV-W for PA1705UL-W/PA1505UL-W NP13CV-B for PA1705UL-B/PA1505UL-B The option covers A and B are packaged with the option cover NP13CV-W and NP13CV-B. For the following cases, attach the separately sold option cover to the projector.
  • Page 185 6. Attachment/detachment of parts sold separately • Option cover A Mounting 1. Remove the two corner caps from the pro- jector. • Keep the removed corner caps for future use. 2. Turn over the projector. CAUTION • For moving the projector, make sure you have at least two people. Attempting to move the projector alone could result in back pain or other injuries.
  • Page 186 6. Attachment/detachment of parts sold separately Removing 1. Turn the two option cover A screws counterclockwise until it turns loosely. • The screws are not removable. 2. Remove the option cover A. Hold up the option cover A to release its two hooks from projector tilt foot. 3.

  • Page 187: Connecting To Other Equipment

    7. Connecting to Other Equipment CAUTION • Be sure to turn off the projector before connecting the projector to an external device. If projected light enters your eyes, it may cause visual impairment. NOTE: • The connection cable is not enclosed with the projector. Please get ready a suitable cable for the connection. For HDMI, LAN, BNC, RS-232C, and AUDIO, please use a shielded signal cable.

  • Page 188: Connecting Your Computer

    7. Connecting to Other Equipment 7-1. Connecting Your Computer • Connect a commercially available HDMI cable between the computer’s HDMI output connector and the projector’s HDMI 1 IN or HDMI 2 IN connector. HDMI 1 IN HDMI 2 IN a: HDMI cable (not supplied) / b: Speaker system •...

  • Page 189: Connecting Audio Video Equipment

    7. Connecting to Other Equipment 7-2. Connecting audio video equipment You can connect the HDMI output of your Blu-ray player, hard disk player, or notebook type PC to the HDMI 1 IN or HDMI 2 IN connector of your projector. The SDI input terminal can also be used to connect to professional video devices, etc.
  • Page 190 7. Connecting to Other Equipment NOTE: • Use cables that are 5C-FB or higher (5C-FB, 7C-FB, etc.) or Belden 1694A or higher. In addition, use cables with a cable length 100m or less. • The length of cables that can be used may differ, depending on the signal. TIP: •...

  • Page 191: Connecting To A Hdbaset Transmission Device (Sold Commercially)

    7. Connecting to Other Equipment 7-3. Connecting to a HDBaseT transmission device (sold commercially) Use a LAN cable sold commercially to connect the HDBaseT IN port of the projector to a HDBaseT transmission device sold commercially. The HDBaseT IN port of the projector supports HDMI signals (HDCP) from transmission devices, control signals from external devices (serial, LAN) and remote control signals (IR commands).

  • Page 192: Connecting Several Projectors

    7. Connecting to Other Equipment 7-4. Connecting several projectors It enables to project HDMI, DisplayPort, HDBaseT image on several projectors connecting the HD- BaseT IN port and the HDBaseT OUT port by LAN cable. The projectors support same brightness can be connected up to four units. HDBaseT OUT HDBaseT IN a: Master projector / b: Other projector...

  • Page 193: Connecting To A Wired Lan

    7. Connecting to Other Equipment 7-5. Connecting to a Wired LAN The projector comes standard with a LAN port which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [NETWORK SETTINGS] →...

  • Page 194: Maintenance

    8. Maintenance 8-1. Cleaning the Lens WARNING • Turn off the power, unplug the power plug from the socket and remove the lens for cleaning. If the unit turns on while cleaning the lens, the strong light from the lens could damage your eyes.

  • Page 195: Cleaning The Cabinet

    8. Maintenance 8-2. Cleaning the Cabinet WARNING • Turn off the projector, and unplug the projector before cleaning. • Please do not use a spray containing flammable gas to remove dust attached to the cabinet. Doing so may result in fires. •...

  • Page 196: Appendix

    9. Appendix 9-1. Throw distance and screen size Six separate bayonet style lenses can be used on this projector. Refer to the information on this page and use a lens suited for the installation environment (screen size and throw distance). Projection range for the different lenses NP51ZL NP52ZL...
  • Page 197 9. Appendix Lens types and throw distance (Aspect ratio 16:10) (Unit: inch) Lens model name and throw distance Screen size Width × Height (inches) NP51ZL NP52ZL NP53ZL NP54ZL NP55ZL NP56ZL 51 × 32 26 – 32 32 – 43 43 – 63 62 –...
  • Page 198 9. Appendix Lens types and throw distance (Aspect ratio 16:9) (Unit: inch) Lens model name and throw distance Screen size Width × Height (inches) NP51ZL NP52ZL NP53ZL NP54ZL NP55ZL NP56ZL 52 × 29 27 - 33 33 - 45 44 - 65 64 - 104 101 - 204 207 - 391 70 ×...
  • Page 199 9. Appendix Calculation of the throw distance from the screen size L: Throw distance W: Screen width Lens model name Calculation formula (Zoom min to max) NP51ZL L = W × 0.5 to W × 0.7 NP52ZL L = W × 0.6 to W × 0.9 NP53ZL L = W ×...
  • Page 200 9. Appendix Lens shifting range This projector is equipped with a lens shift function for adjusting the position of the projected im- age by buttons. The lens can be shifted within the range shown below. • See page for lens shift operations and precautions. •...
  • Page 201 9. Appendix Example: When projecting on a 16:10 150" screen using the NP54ZL lens: According to the "Lens types and throw distance (Aspect ratio 16:10)" (→ page 000), H (screen width) = 323.1 cm and V (screen height) = 201.9 cm Adjustment range in the vertical direction: Upper and lower directions of 0.65 ×...

  • Page 202: Compatible Input Signal List

    9. Appendix 9-2. Compatible Input Signal List HDMI Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) Bit Depth Signal Type 640 × 480 4 : 3 SVGA 800 × 600 4 : 3 1024 × 768 4 : 3 1280 ×...
  • Page 203 9. Appendix HDBaseT Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) Bit Depth Signal Type × 480 SVGA 800 × 600 4 : 3 1024 × 768 4 : 3 1280 × 720 16 : 9 WXGA 1280 ×...
  • Page 204 9. Appendix *1 Native resolution *2 [BIT DEPTH] will not appear in the [INFO.] → [SOURCE(2)] menu during YCbCr4:2:2 usage. • With Advanced AccuBlend, the size of characters and ruled lines may be uneven and colors may be blurred. • Upon shipment, the projector is set for signals with standard display resolutions and frequencies, but adjust- ments may be required depending on the type of computer.

  • Page 205: Specifications

    9. Appendix 9-3. Specifications Model name PA1705UL-W/PA1705UL-B PA1505UL-W/PA1505UL-B Method Three primary color liquid crystal shutter projection method Specifications of main parts Liquid crystal Size 1.0" × 3 (aspect ratio: 16:10) panel Pixels 2,304,000 (1920 dots × 1200 lines) (*1) Projection lenses Refer to the specifications of option lens (→...
  • Page 206 9. Appendix Model name PA1705UL-W/PA1705UL-B PA1505UL-W/PA1505UL-B Usage environment Operating temperature: 32 to 113°F (0 to 45°C) (*5) Operating humidity: 20 to 80% (with no condensation) Storage temperature: 14 to 122°F (−10 to 50°C) Storage humidity: 20 to 80% (with no condensation)
  • Page 207 9. Appendix Option lens (sold separately) NP51ZL Throw ratio 0.53–0.65 : 1, F1.85–2.20, f=12.0-14.6 mm NP52ZL Throw ratio 0.65–0.87 : 1, F1.84–2.25, f=14.4-19.1 mm NP53ZL Throw ratio 0.86–1.25 : 1, F1.80–2.24, f=19.0-27.6 mm NP54ZL Throw ratio 1.24–2.01 : 1, F1.80–2.24, f=27.7-44.3 mm NP55ZL Throw ratio 1.98–3.95 : 1, F1.84–2.58, f=43.8-86.0 mm NP56ZL...

  • Page 208: Cabinet Dimensions

    9. Appendix 9-4. Cabinet Dimensions Unit: mm (inch) 599 (23.6) 540 (21.3) 300 (11.8) 150 (5.9) a: Lens center / b: 6 M4mm screw holes of 8mm depth...

  • Page 209: Pin Assignments And Signal Names Of Main Connectors

    9. Appendix 9-5. Pin assignments and signal names of main connectors HDMI 1 IN/HDMI 2 IN Connector (Type A) Pin No. Signal TMDS Data 2+ 2 4 6 8 10 12 14 16 18 1 3 5 7 9 11 13 15 17 19 TMDS Data 2 Shield TMDS Data 2−...
  • Page 210 9. Appendix PC CONTROL Port (D-Sub 9 Pin) Pin No. Signal Unused RxD reception data TxD transmission data Unused Grounding Unused RTS transmission request CTS transmission allowed Unused...

  • Page 211: Changing The Background Logo (Virtual Remote Tool)

    Remote Control Window Toolbar For getting the Virtual Remote Tool, please visit our web site and download it: https://www.sharp-nec-displays.com/dl/en/index.html NOTE: • Remote Control Window is not available for changing the background logo. Please see the HELP menu of the Virtual Remote Tool about how to display the Toolbar.

  • Page 212: Portrait Projection (Vertical Orientation)

    9. Appendix 9-7. Portrait projection (vertical orientation) Portrait screens from a computer can be projected by installing the projector in a vertical orientation. Precautions during installation • Please do not install the projector in a vertical orientation on top of the floor or table on its own.
  • Page 213 9. Appendix Reference drawings * The drawing showing the dimensional requirements is not an actual stand design drawing. (Unit: mm) [Front View] [Side View] a: Intake air / b: Exhaust / c: Screw 6 - M4 / d: Horizontal adjuster ** The example shows the right side of the body (side where the control unit is located) facing downwards.

  • Page 214: Troubleshooting

    9. Appendix 9-8. Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Feature of each indicator ① POWER indicator ① ② ③ ④ ② STATUS indicator ③ LIGHT indicator ④ TEMP. indicator Indicator Message (Status message) POWER STATUS...
  • Page 215 9. Appendix POWER STATUS LIGHT TEMP. Projector status Powered state ([REF. LIGHT MODE] is [SILENT] or [LONG LIFE]) Blue Green (Light) (Blink* [LENS CALIBRATION] implement request. Status varies Orange Status varies (Blink* Performing the lens calibration Blue Green Status varies (Light) (Blink* Shutter function is activating...
  • Page 216 9. Appendix Indicator Message (Error message) POWER STATUS LIGHT TEMP. Projector status Procedure A button has been The [CONTROL PANEL pressed while the [CON- LOCK] is activated. The Blue Orange Status varies TROL PANEL LOCK] is setting must be canceled activated.
  • Page 217 9. Appendix When the thermal protector is activated: When inside temperature of the projector becomes too high or low, the POWER indicator start to red blink in a short cycle. After this happened, the thermal protector will activate and the projector may be turned off.
  • Page 218 9. Appendix Common Problems & Solutions (→ “Indicator Message” on page 191.) Problem Check These Items Does not turn on or shut • Check that the power cord is plugged in and that the power button on the projector cabinet or the down remote control is on.
  • Page 219 9. Appendix Problem Check These Items Image is scrolling vertically, • Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display horizontally or both is supported by the projector. (→ page 177) • Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 102) Remote control does not •...

  • Page 220: Pc Control Codes And Cable Connection

    9. Appendix 9-9. PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON POWER OFF INPUT SELECT HDMI1 INPUT SELECT HDMI2 INPUT SELECT HDBaseT INPUT SELECT SDI PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF NOTE: •...
  • Page 221 9. Appendix PC Control Terminal (D-Sub 9P) To TxD of PC To RxD of PC To GND of PC To RTS of PC To CTS of PC NOTE: • Pins 1, 4, 6 and 9 are no used. • Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection. •...

  • Page 222: About The Ascii Control Command

    This device supports the common ASCII Control Command for controlling our projector and monitor. Please visit our web site for detailed information about the command. https://www.sharp-nec-displays.com/dl/en/pj_manual/lineup.html How to connect with an external device There are two methods to connect the projector with an external device such as a computer.
  • Page 223 9. Appendix Parameters for this device Input command Input terminal Response Parameter HDMI1 hdmi1 hdmi1 or hdmi HDMI2 hdmi2 hdmi2 HDBaseT hdbaset hdbaset or hdbaset1 sdi or sdi1 Status command Response Error Status error:temp Temperature error error:fan Fan trouble error:light Light source trouble errorl:lens Lens trouble...

  • Page 224: List Of Art-Net Dmx Parameters

    9. Appendix 9-11. List of Art-Net DMX parameters Function Behavior Parameter Note POWER 0 – 63 No operation 64 – 191 192 – 255 INPUT No operation 0 – 7 HDMI1 8 – 15 No operation 16 – 23 HDMI2 24 –...

  • Page 225: Troubleshooting Check List

    9. Appendix 9-12. Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently. * Print this page and the next page for your check.
  • Page 226 In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Signal cable Model number: NEC standard or other manufacturer’s cable? Serial No.: Model number: Length: inch/m Date of purchase:...

  • Page 227: Register Your Projector! (For Residents In The United States, Canada, And Mexico)

    Upon receipt, we will send a confirmation letter with all the details you will need to take advantage of fast, reliable warranty and service programs from the industry leader, Sharp NEC Display Solu- tions of America, Inc.
  • Page 228 © Sharp NEC Display Solutions, Ltd. 2023...

This manual is also suitable for:

Pa1705ul-bPa1505ul-wPa1505ul-b6000597260005932

Table of Contents