Bosch 0600910300 Original Instructions Manual page 12

OBJ_BUCH-1763-001.book Page 11 Friday, August 17, 2012 8:49 AM
Pressure washer
Flow rate
Maximum input pressure
Repulsive force at the gun to the
maximum pressure
Motor Insulation
Motor Protection
Detergent tank
Autostop function
Net impedance
Weight according to
EPTA-Procedure 01/2003
Protection class
Serial number
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0,153 ohm.
Noise/Vibration Information
Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 85.5 dB(A); sound power level
93 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335:
2 2
a =4.91 m/s , K=1.5 m/s .
h
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 93 dB(A). Con-
formity assessment procedure according to Annex V.
Equipment category: 27
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider Helmut Heinzelmann
Senior Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
29.06.2012
Bosch Power Tools
Mounting and Operation
GHP 8-15 XD
l/min 12.6
Action
MPa 1
Delivery Scope
Handle Assembly
N 33.24
Mounting the hose
Class F
Insert dip stick for ventilation
IPX5
Filling up detergent tank
Water connection
Clean the water strainer
–
Connecting high pressure water supply hose/
nozzle
kg 41
Adjust water pressure
/I
Adjust water jet
See serial number (rating
Switching on and off
plate) on pressure washer.
Clean nozzle
Starting
For Your Safety
Your pressure washer requires an earth connection. The op-
erating voltage is 400 V AC, 50 Hz. Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
– 2.5 mm
– 4.0 mm
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
2
– max length 20 m
2
– max length 50 m
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
F 016 L72 357 | (17.8.12)
English | 11
Figure
1
2
3
4
5
6
7
8
9
10
11
12