Table of Contents
Advertisement
Names and functions of the Function Board (optional)
This projector is equipped with Intel
Function Board supporting the Intel
specification can be installed in the slot.
The terminal names of the optional Function Board with image input terminal to be used in this document is
defined here, and also their operations are explained. Also refer to the Operating Instructions of the Function
Board.
12G-SDI Terminal Board (Model No.: TY-SB01QS)
This board supports the HD-SDI signal, 3G-SDI signal, and 12G-SDI signal.
1
<SDI 4 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
2
<SDI 3 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
3
<SDI 2 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
Note
f The <SDI 2 IN>/<SDI 3 IN>/<SDI 4 IN> terminals are used when the quad link signal is input. These terminals do not support input of
12G-SDI signal.
f When the projector is in standby mode, a signal is not output from the <SDI OUT> terminal.
f This projector is not equipped with an audio function so it is not possible to output audio, but the audio signal input to the <SDI 1 IN>
terminal is output from the <SDI OUT> terminal.
Function Board for 12G-SDI Optical Fiber (Model No.: TY-SB01FB)
This board is equipped with two ports that can install the SFP (Small Form-Factor Pluggable)/SFP+ module
(referred to as "SFP module" hereinafter), and supports the HD-SDI signal, 3G-SDI signal, and 12G-SDI signal.
1
SFP port 1
This is the port to install the SFP module for receiving.
2
SFP port 2
This is the port to install the SFP module for sending and
receiving.
Note
f SFP module is an expansion module to convert optical signal to electric signal, or to convert electric signal to optical signal.
f Prepare the commercially available SFP module and the optical fiber cable required for connection according to the usage, image signal to
be input, specification of the external device to be connected, etc.
f Operation of the sending function is restricted depending on the port where the SFP module is installed.
f SFP modules compatible with this board must be corresponding to at least one of the following.
g 12G-SDI/3G-SDI/HD-SDI compatible optical fiber SFP modules that are compliant with MSA (Multi-Source Agreement)
g Optical fiber SFP modules that the operation has been verified by Panasonic Connect Co., Ltd.
f For the SFP modules that the operation has been verified with this projector, visit the following website.
https://panasonic.net/cns/projector/
Confirmation of operation for SFP module has been performed with the items set independently by Panasonic Connect Co., Ltd., and not all
the operations are warranted. For operation or performance problems caused by the SFP module, contact the respective manufacturers.
f The sending function of the SFP module for sending or for sending and receiving will not operate when it is installed in the SFP port 1.
f In addition to the SFP module for sending and receiving, the SFP module for receiving or for sending can be installed in the SFP port 2.
Chapter 1 Preparation — About your projector
Smart Display Module (Intel
®
SDM Small (Intel
®
4 IN
3 IN
TY-SB01QS
3G SDI
1
2
1
2
SDM) specification slot.
®
SDM-S) or the Intel
®
®
2 IN
OUT
1 IN
12G/3G SDI
3
4
5
4
<SDI OUT> terminal
This is an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/12G-SDI) input to the <SDI 1 IN> terminal.
5
<SDI 1 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI/12G-SDI).
3
3
Input indicator <SIGNAL>
This is the indicator to indicate the detection state of the image
signal. This is illuminated when input of the image signal is
detected in either or both of the <SDI OPT 1 IN> terminal and
the <SDI OPT 2 IN> terminal.
SDM Large (Intel
SDM-L)
®
ENGLISH - 33
Advertisement
Table of Contents
