HIKVISION DS-PD2-T12P-WEL - 12m Wireless Outdoor Detector Manual

Also See for DS-PD2-T12P-WEL:

Manual (2 pages)

User manual (4 pages)

Table of Contents

Contents

1 Installation
2 Switches
3 Microwave range and angle of detection
4 LEDs
5 Lens inserts
6 Registration procedure
- 6.1 Register Locally
7 Initialize the Detector
8 Signal strength test
9 Technical Specification
10 Battery Information
11 Documents / Resources
- 11.1 Download manual

HIKVISION DS-PD2-T12P-WEL - 12m Wireless Outdoor Detector Manual

Installation

Installation - Step 1
Installation - Step 2
Ensure that the detector is installed away from reflected sunlight and large objects.

Switches

	ON position	OFF position
1	LEDs on	LEDs off
2	Buzzer on	Buzzer off
3	Top PIR high sensitivity	Top PIR low sensitivity
4	Bottom PIR high sensitivity	Bottom PIR low sensitivity

Microwave range and angle of detection

Use the highlighted dials to change the microwave range and angle of detection.

LEDs

LEDs
Four LEDs show the status of the detector.

	Top PIR activated
	Bottom PIR activated
	Microwave activated
	Alarm
	Powering up
	Low battery

Lens inserts

Use lens inserts to control the coverage area.

Registration procedure

After powering up and after registration, there is a 10 minute timer that allows a walk test of the PIR and microwave sensors. You can set up the sensitivity and microwave range without using the control panel to perform a walk test. After 10 minutes, the detector enters sleep mode. Please register the device within 90 seconds after it being powered on.

Register Locally

Make the security control panel enter the registration mode.
Register the detector: Hold the registration key until the three LEDs flash alternately. The green LED will flash 8 times if the registration is finished.
Communication Test: Release the TEMPER spring to trigger the alarm. Note: The distance between the security control panel and the detector should be less than 50 cm.

Initialize the Detector

Remove the battery to power the detector off.
5s later, hold the registration key and reinstall the battery to power thedetector on at the same time to make the three LEDs start flashing alternately. Release the registration key while the three LEDs flash once together.

Signal strength test

Signal strength test Enter the signal checking mode by operating on the control panel Indicator turns green: Strong Signal. Indicator turns red: Weak Signal.

Technical Specification

Detectors Technical Characteristics
Detection Range	12m
Detection Angle	90°
Detection Zones	2x22 zones
Detection Speed	0.25–2.5 m/s
Mounting Height	1-1.5 m
Two-way Wireless Technology	Yes
Blue Wave Technology	Yes
Dual Element Pyroelectric Sensor	Yes
Tamper Protection	Front, rear, and bracket tamper signal input
Intergrated Walk Test Buzzer	Yes
Separated LED Indication:	Top: Microwave, PIR 1 and alarm
Orange(Microwave),Blue(Alarm),Green(PIR)	Bottom: PIR 2
Signal Strength Indicators (SSI)	Yes
3 Microwave Frequencies to Avoid Interference	Yes
Digital Independent Floating Threshold(IFT) Technology	Yes
Plastic Housing	3mm polycarbonate
Animal Immunity	Up to 24kg
Optics	Dual-vision sealed optics
Adjustable Sensitivity	High or low range
Lens	UV compensated
Detection Method	Tri-Signal Detection Logic
Sensor	2 low noise dual element passive infrared sensors and a microwave doppler unit
Environmental and Operating Features
Weatherproof	IP55 rated
Certified Operating Temperature	-25 to +60 (Certified)
Physical Dimensions(H x W x D)	118mm x 77mm x 84mm
Weight	0.3kg
Electrical & battery
Battery Type	2x3V 4700mAh Lithium battery packs
Battery Life	Up to 3 years
Battery Capacity	4700mAh
Accessories
Rotatable Wall Mounted	Yes – additional wall and fixed brackets available separately
Fixed Wall Mounted	Yes – additional wall and fixed brackets available separately
Ceiling Mounted	Yes – additional wall and fixed brackets available separately
Battery	Yes – additional battery available separately

Battery Information

The batteries supplied with this product have been chosen to provide long service life whilst, for safety reasons, having limited output current. The battery leads must be connected for operation. When disposing of the product, remove the batteries and disposed of separately in accordance with the local regulations.