Panasonic ACXF60-03410 - Wired Remote Controller Installation Manual

Also See for ACXF60-03410:

Table of Contents

ATTACHED ACCESSORIES

No.	Name	Qty	Diagram	Remark
1	Remote controller	1
2	Remote controller cable	1		Length 32.8ft (10m)
3	Screw (M4 machine pitched - 1 3/16" 30mm))	3		Installing the remote controller to an outlet box (embedded cable)
4	Screw (M4 self tapping - 9/16"(14mm))	3		Installing the remote controller to the wall (exposed cable)

Allow sufficient space around the remote controller as shown in the illustration below.
Install in a place which is away from direct sunlight and high humidity.
Install on a flat surface to avoid warping of the remote controller. If installed to a wall with an uneven surface, damage to the LCD case or operation problems may result.
Install in a place where the LCD can be easily seen for operation. (Standard height from the floor is 3.9ft to 4.9ft (1.2 to 1.5 meters.))
Avoid installing the remote controller cable near refrigerant pipes or drain pipes, otherwise it will cause electrical shock or fire.

Remove the remote controller mounting plate.
(Insert a flat-tipped screw driver or similar tool 3/32" to 1/8" (2 to 3 mm) into one of the gaps at the bottom of the case, and twist to open. Refer to the illustration below)
Be careful not to damage the mounting plate.
Do not remove the protective tape which is affi xed to the upper case circuit board when removing the remote controller mounting plate.
Secure the mounting plate to an outlet box or wall. Refer to (A) or (B) instructions below depending on your choice of cable installation.
Be sure to use only the screws provided.
Do not over tighten the screws, as it may result in damage to the mounting plate.

Embed an outlet box into the wall. Outlet box may be purchased separately. Medium-sized square outlet box (obtain locally) Part No. DS3744 (Panasonic Corporation) or equivalent.
Secure the remote controller mounting plate to the outlet box with the two accessory screws . Make sure that the mounting plate is fl at against the wall at this time, with no bending.
Pass the remote controller cable into the box.
Route the remote controller cable inside the mounting plate through rear feeding-out direction.
Insert firmly the connector of remote controller cable to connector (CON1) in the upper case circuit board.
Secure the remote controller upper case to the mounting plate with the tabs provided.

When the wall is hollow, please be sure to use the sleeve for remote controller cable to prevent dangers caused by mice biting the cable.

Install the remote controller mounting plate to the wall with the two accessory screws .
Fasten the screws properly until screw head is lower than the rib and reach the base of remote controller mounting plate to ensure they do not damage the PCB inside the remote controller .
The feeding-out direction for the remote controller cable can be either via top, left or right side.
Use nipper to cut a notch at the upper case. (Select the intended feeding-out position)
Route the remote controller cable inside the mounting plate in accordance with the intended feeding-out direction.
Insert firmly the connector of remote controller cable to connector (CON1) in the upper case circuit board. (Refer to the illustration above)
Secure the remote controller upper case to the mounting plate with the tabs provided.

Be sure to turn off the main power before installing and connecting the remote controller.
Otherwise, it will cause electrical shock.

Open the indoor control box cover by removing two pieces of screws.
Remove the plugs at the side of the control box and fi x the conduit connectors to knockout holes with lock nuts.
Guide the remote controller cable 2 into the unit through the upper knockout hole and secure the cable to the holder.
Firmly connect the connector of remote controller cable 2 to indoor unit PCB connector.
Guide the remote controller cable 2 earth wire into the control box through the upper knockout hole.
Fix the earth wire with a screw to the grounding location provided in the control box.
Install back the control box cover. Be careful not to clamp the cable in between control box and control box cover.