Related Manuals for Zennio QUAD Plus
Summary of Contents for Zennio QUAD Plus
- Page 1 QUAD Plus Analogue/Digital Input Module for Motion Sensors, Temperature Probes and Binary Inputs ZNIO-QUADP Application program version: [1.1] User manual edition: [1.1]_a www.zennio.com...
-
Page 2: Table Of Contents
QUAD Plus CONTENTS Contents ............................2 Introduction .......................... 3 1.1 QUAD Plus ........................3 1.2 Installation ........................3 Configuration......................... 5 2.1 General ..........................5 ETS Parameterisation ....................5 2.2 Inputs ..........................6 2.2.1 Binary Input ......................6 2.2.2 Temperature Probe ....................6 2.2.3... -
Page 3: Introduction
QUAD is connected to the KNX bus through the incorporated terminal connector, while the input lines need to be connected to QUAD Plus through the screw terminal block bundled in the device packaging. Once powered through the KNX bus, the device may be downloaded both an individual address or the application program. - Page 4 1 to 4 and, on the other hand, to any of the common slots, labelled as “C”. To obtain further information about the technical features of QUAD Plus and on security and installation procedures, please refer to the Datasheet of the device, bundled with the original packaging and also available at the Zennio website, http://www.zennio.com.
-
Page 5: Configuration
QUAD Plus 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by right-clicking into the device and selecting Edit parameters. ETS PARAMETERISATION The only parameterisable screen available by default is General. From this screen it is possible to activate/deactivate all the required functionality. -
Page 6: Inputs
It is possible to connect motion detectors (models ZN1IO-DETEC-P and ZN1IO- DETEC-X from Zennio) to the input ports of QUAD Plus. This brings the device with the possibility of monitoring motion and presence in the room, as well as the light level. - Page 7 Motion detectors with references ZN1IO-DETEC and ZN1IO-DETEC-N are not compatible with QUAD Plus (may report inaccurate measurements if connected to this device). When connected to QUAD Plus, the rear micro-switch of model ZN1IO- DETEC-P should be set to position “Type B”. http://www.zennio.com Technical Support: http://support.zennio.com...
-
Page 8: Thermostats
QUAD Plus 2.3 THERMOSTATS QUAD Plus allows independently enabling and configuring up to four thermostat functions, with independence of the number of the inputs that have been configured. Please refer to the specific “Zennio Thermostat” user manual available under the QUAD Plus product section at the Zennio homepage (www.zennio.com) for detailed... -
Page 9: Annex I. Communication Objects
QUAD Plus ANNEX I. COMMUNICATION OBJECTS “Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself. - Page 10 QUAD Plus -273.00 - C - - W - 2 Bytes DPT_Value_Temp [Tx] Setpoint Thermostat Setpoint Input 670760.00 14, 44, 74, 104 -273.00 - 2 Bytes C - - W - DPT_Value_Temp [Tx] Basic Setpoint Reference Setpoint 670760.00 15, 45, 75, 105...
- Page 11 QUAD Plus 1 Bit C T - - - DPT_UpDown [Ix] [Short Press] Move Up Shutter Sending of 0 (Up) 1 Bit C T - - - DPT_UpDown [Ix] [Short Press] Move Down Shutter Sending of 1 (Down) 1 Bit...
- Page 12 QUAD Plus 1 Byte C T - - - DPT_SceneControl 0-63 [Ix] [Short Press] Run Scene Sending of 0 - 63 1 Byte C T - - - DPT_SceneControl 128-191 [Ix] [Short Press] Save Scene Sending of 128 - 191...
- Page 13 QUAD Plus 0x8 (Stop) 0x9 (Inc. by 100%) … 0xF (Inc. by 1%) C T - - - 1 Bit DPT_Switch [Ix] [Long Press] Dimmer ON Sending of 1 (ON) C T - - - 1 Bit DPT_Switch [Ix] [Long Press] Dimmer OFF...
- Page 14 QUAD Plus 177, 206, 235, 264 1 Bit C T R - - DPT_Occupancy [Ix] Presence: Occupancy State 0 = Not Occupied; 1 = Occupied 0 = Nothing; 1 = Motion detected by an external C - - W -...
- Page 15 Join and send us your inquiries about Zennio devices: http://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002 www.zennio.com info@zennio.com...