Samsung HG43RU750A, HG49RU750A - UHD TV Quick Setup Guide

Also See for HG43RU750A:

Install manual (55 pages)

Table of Contents

Contents

1 List of Parts
2 Installing the batteries
3 Installing the Unit Stand
4 Viewing the Connection Panel
5 Connecting the Device to a SBB or STB
6 Wall Mount Kit Specifications (VESA)
7 Specifications
8 Documents / Resources
- 8.1 Download manual

Samsung HG43RU750A, HG49RU750A - UHD TV Quick Setup Guide

List of Parts

The provided accessories may vary depending on the model.

Installing the batteries

Battery size: AAA
Installing the batteries

Installing the Unit Stand

Assembling the Stand and Components

Assembling the Stand and Components - Used parts
When installing the stand, use the provided components and parts.

Assembling the Stand and Components - Step 1

Place a soft cloth over the table to protect the TV, and then place the TV so that its screen faces down toward the table surface.
Insert the Stands into the slot on the bottom of the TV.
Slide and assemble it to the end line in the direction of arrow.

Assembling the Stand and Components - Step 2

NOTE

Make sure to distinguish between the front and back of each component when assembling them.
Make sure that at least two persons lift and move the TV.

Viewing the Connection Panel

Connecting the Device to a SBB or STB

Connecting the Device to a SBB or STB
Connect the DATA port of the TV to the ETH MODEM port of the STB (SBB) with the Data cable.

The ETH MODEM port name that you connect the Data Cable to may differ depending on the SBB or STB type.
IR signals sent by the remote control to the TV or SBB / STB must meet the following specification to use IR pass through function. IR signal reciever specification
- Band pass filter centre frequency: 37.9 ㎑
- Carrier Frequency, Duty 50%
- Minimum Burst Length (tburst): 12 pulses (316 us)
- Minimum Gap Time Between the burst (tburst gap): 16 pulses (422 us)
- Minimum Gap Time between the data commands (tpause): 25 ㎳

List of Hospitality SI Vendors and compatible data cables supplied with the TV

Confirm you are using the correct data cable for your SI vendor. Refer to the code label on the data cables.

Contact your nearest dealer or your SI Vendor to buy the data cable not included in the TV.
RX and TX notation is based on TV.
Operation Specification of Data Cable(RJ12): RS232

Wall Mount Kit Specifications (VESA)

The Wall mount kit is not supplied but sold separately.

Install your wall mount on a solid wall, perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installing on a ceiling or slanted wall, it may fall and result in severe personal injury.
Using the Wall Mount Kit

Standard dimensions for wall mount kits are shown in the table follow.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
Do not use screws that do not comply with VESA standard screw specifications.
Do not use screws longer than the standard dimensions, as they may cause damage to the inside of the TV set.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.
Do not fasten the screws too tightly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Do not exceed a 15 degrees tilt when mounting this TV.
When installing a wall mount kit, we recommend you fasten all four VESA screws.
If you want to install a wall mount kit that attaches to the wall using two top screws only, be sure to use a Samsung wall mount kit that supports this type of installation. (You may not be able to purchase this type of wall mount kit, depending on the geographical region.)

TV size in inches	VESA screw hole specs (A * B) in millimetres	C (mm)	Standard Screw	Quantity
43-55	200 x 200	43-45	M8	4
65-75	400 x 400

shock hazard Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.

Specifications

Model Name	HG43RU750A	HG49RU750A
Display Resolution	3840 x 2160	3840 x 2160
Screen Size Measured Diagonally	108 cm	123 cm
Sound (Output)	20 W	20 W
Dimensions (W x H x D)
Body	97.02 x 56.32 x 5.82 cm	110.28 x 63.78 x 5.91 cm
With stand	97.02 x 63.63 x 21.03 cm	110.28 x 71.64 x 26.13 cm
Weight
Without Stand	9.6 kg	13.2 kg
With Stand	9.8 kg	13.5 kg
Model Name	HG50RU750A	HG55RU750A
Display Resolution	3840 x 2160	3840 x 2160
Screen Size Measured Diagonally	125 cm	138 cm
Sound (Output)	20 W	20 W
Dimensions (W x H x D)
Body	112.48 x 65.02 x 5.91 cm	123.86 x 71.42 x 5.87 cm
With stand	112.48 x 72.88 x 26.13 cm	123.86 x 79.28 x 26.13 cm
Weight
Without Stand	13.6 kg	17.3 kg
With Stand	13.9 kg	17.7 kg
Model Name	HG65RU750A	HG75RU750A
Display Resolution	3840 x 2160	3840 x 2160
Screen Size Measured Diagonally	163 cm	189 cm
Sound (Output)	20 W	20 W
Dimensions (W x H x D)
Body	145.75 x 83.73 x 5.91 cm	168.46 x 96.64 x 6.01 cm
With stand	145.75 x 91.73 x 31.28 cm	168.46 x 105.65 x 35.61 cm
Weight
Without Stand	25.0 kg	37.0 kg
With Stand	25.5 kg	37.5 kg
Environmental Considerations
Operating Temperature	50°F to 104°F (10°C to 40°C)
Operating Humidity	10% to 80%, non-condensing
Storage Temperature	-4°F to 113°F (-20°C to 45°C)
Storage Humidity	5% to 95%, non-condensing

The design and specifications are subject to change without prior notice.
For information about the power supply, and more information about power consumption, refer to the label-rating attached to the product.
You can see the label-rating attached to the back of the TV. (For some models, you can see the label-rating inside the cover terminal.)