Epson ELPGS03 - 3D Glasses Manual

Introduction

Use these glasses to enjoy the full 3D effect when viewing 3D images from a 3D projector.

Supplied Items

3D Glasses x 1,
Glasses cleaner x 1,
Soft case x 1,
USB charging cable (1 m) x 1

Part Names

1. Shutter,
2. Nose pad (Adjustable width),
3. Power switch,
4. Indicator,
5. Pairing button

Reading the Indicator (d)

Charging

1. Using the WirelessHD Transmitter
2. Using the USB Charging Adapter

The following outlines standard charging times.

• Approximately 50 minutes (Allows approximately 40 hours of use)
• Charging for three minutes allows approximately three hours of use.

These are approximate charge and use times. Battery life may vary depending on the usage conditions and the operating environment. Also, the rechargeable battery deteriorates over time which gradually reduces the amount of time the 3D Glasses can be used between charges.
The battery is not fully charged at the time of purchase. Make sure you charge them before use.

Viewing (Turning On)

Turn on the 3D Glasses. The indicator turns green for 10 seconds and then turns off. If the power turns off automatically, move the power switch to Off, and then move it back to On.

Turning Off

Turn off the power switch on the 3D Glasses.
If the glasses are not used for 30 seconds or more when no image signal is being input, the power turns off automatically.

Pairing

Perform pairing if 3D images are not displayed correctly.

1. Turn on the 3D Glasses when a 3D image is being projected. Do not connect the USB charging cable.
2. Hold down the Pairing button for three seconds.

The indicator flashes alternately green and red. If pairing is successful, the indicator turns green for 10 seconds and then turns off. You can also check the message on the projected screen. When performing pairing, the amount of charge remaining in the 3D Glasses and the MAC address are displayed on the projected screen.

You can perform pairing within a range of three meters from the projector. Make sure you are no more than three meters from the projector. If pairing is not successful, the 3D Glasses turn off.

• Do not disassemble or remodel the 3D Glasses. This could cause a fire to occur or the images to appear abnormal when viewing, causing you to feel unwell.
• Do not leave the 3D Glasses within reach of children.
• Electromagnetic interference may cause medical equipment to malfunction. Before using the device, make sure there is no medical equipment in the vicinity.
• Electromagnetic interference may cause automatically controlled equipment to malfunction which could cause an accident. Do not use the device near automatically controlled equipment such as automatic doors or fire alarms.

• Do not drop or press too forcefully on the 3D Glasses. If the glass sections and so on are broken, an injury could occur. Store the glasses in the soft glasses case supplied.

• Be careful of the edges of the frame when wearing the 3D Glasses. If it pokes your eye and so on, an injury could occur.
• Do not place your finger in any of the moving sections (such as the hinges) of the 3D Glasses. Otherwise an injury could occur.
• Make sure you wear the 3D Glasses correctly. Do not wear the 3D Glasses upside down. If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell.
• How a 3D image is perceived varies depending on the individual. Stop using the 3D function if you feel strange or cannot see in 3D. Continuing to view the 3D images could cause you to feel unwell.
• Stop wearing the 3D Glasses immediately if they seem abnormal ora malfunction occurs. Continuing to wear the 3D Glasses could cause an injury or cause you to feel unwell.
• Stop wearing the 3D Glasses if your skin feels unusual when wearing the glasses. In some very rare cases the paint or materials used in the 3D Glasses could cause an allergic reaction.

Notice

• The communication method for 3D Glasses uses the same frequency (2.4 GHz) as wireless LAN (IEEE802.1 1 b/g) or microwave ovens. Therefore, if these devices are used at the same time, radio wave interference may occur, the image may be interrupted, or communication may not be possible. Do not use the projector near these devices.
• The 3D Glasses for this projector use the active shutter system based on the standards provided by the Full HD 3D Glasses Initiative^TM.
• A rechargeable battery is provided with the 3D Glasses. Follow your local rules and regulations when disposing of the battery.
• If you do not use the 3D Glasses, make sure you charge them once every six months. The performance of the rechargeable battery may deteriorate if it is not used for an extended length of time.
• If you notice any abnormalities or damage, stop using the 3D Glasses immediately and contact your local dealer or the Epson Service Center mentioned in the "User's Guide" supplied with the projector.

See the User' Guide supplied with the projector for more details.

Specification

Operating temperature: 0 ~ 40' C
Storage temperature: ~10~60 'C
Overall dimension: 167.2(W) X 4S.4(H) X 169.9(D) mm
Mass: Approx. 35 g

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Epson ELPGS03 - 3D Glasses Manual