Honeywell 40954 - Daysmart 7-Day In-Wall Timer Manual

Table of Contents

Contents

1 SET TIME
2 SETTINGS
3 PROGRAMMING OPTIONS (PRESET)
4 RESET BUTTON
5 SPECIFICATIONS
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

SET TIME

Use up ( ) and down ( ) arrows to set current time.
Take note of the AM/PM setting.
Note: When timer is reset, the time will flash.

SETTINGS

Press and hold set button ( ) for 3 seconds and current time will flash on the screen. Release set button. Use ( ) to select current time and press set button ( )
"YEAR" will flash on the screen. Use ( ) to select the current year and press set button ( ).
"MONT" will flash on the screen. Use ( ) to select the current month and press set button ( ).
"DAY" will flash on the screen. Use ( ) to select the current day and press set button ( ).
"ZONE" will flash on the screen. Use ( ) to select current zone (see Figure 1). Zone is used to determine sunrise/sunset times.
"DST" (daylight saving time) will flash on the screen. Use ( ) to select "ON" if you would like the timer to automatically adjust for daylight savings time or "OFF" if you would not like the timer to adjust automatically.
Note: If no button is pushed for 10 seconds, the timer returns to clock mode. To reenter settings, press and hold set button ( ) for 3 seconds. Use the ( ) to scroll to the desired setting.
Once settings are complete, either wait 10 seconds and the timer automatically reverts to clock mode, or press and hold set button ( ) for 3 seconds.

PROGRAMMING OPTIONS (PRESET)

Note: An illuminated LED on a button indicates the program is active. To deactivate program, press the button again and the LED will turn off.

Evening – Sunset to 12AM:
Press EVENING button and the sunset time will flash on the screen. Use arrows ( ) to adjust time up to 1 hour in either direction and press set button ( ). Days of the week will flash on the screen. Use arrows ( ) to select the correct day options and press set ( ).

On time:
Press and release ON TIME button and the clock will begin flashing. Use arrows to set the desired on time ( ) and press set button ( ). Default is 6PM for all days. Days of the week will then flash on screen. Use arrows ( ) to select the day(s) you want the timer to be active and press set button ( ).

Off time:
Press and release OFF TIME button and the clock will begin flashing. Select desired off time and press set button ( ). Default is 10PM for all days. Days of the week will then flash on-screen. Use arrows ( ) to select the day(s) you want the timer to be active and press set button ( ).

Sunset on:
Press and release SUNSET ON button and the sunset time will flash on the screen. Use arrows ( ) to adjust time up to 1 hour in either direction and press set button ( ). Days of the week will then flash onscreen. Use arrows ( ) to select the day(s) you want the timer to be active and press set button ( ).

Sunrise off:
Press and release SUNRISE OFF button and the sunrise time will flash on the screen. Use arrows ( ) to adjust time up to 1 hour in either direction) and press set button ( ). Days of the week will then flash on-screen. Use arrows ( ) to select the day(s) you want the timer to be active and press set button ( ).

Extra programs:
This option offers seven additional ON/OFF programs. Press and release EXTRA PROGRAMS button and "ON 1" will flash on-screen but no time will be displayed, only "--:--." Press set button ( ) to select program "ON 1" and the "--:--" will flash on screen. Use arrows ( ) to select time and press set button ( ). Days of the week will then flash on-screen.
Use arrows ( ) to select the desired days of the week and press set button ( ). Program On 1 is now set. To go to the next program, use the arrows ( ) and press set button ( ) on the next program you want to set. Repeat these steps for Program Off 1, Program On 2, Program Off 2, etc.

To skip through without setting, simply stop pressing buttons and the display will revert to clock mode after 10 seconds or press set button ( ). You can also use the arrows ( ) to scroll through the options without setting a time. After Program Off 7, the menu will start over with Program On 1. The LED indicator light will remain on if any of the additional programs are set.

To delete one of the extra programs, use arrows ( ) to choose the program you wish to delete and press set button ( ) to select program. Use arrows ( ) to scroll time to between 11:59PM and 12:00AM. The display will show "--:--" to confirm the program has been deleted. No additional steps are needed. The display will revert back to clock mode after 10 seconds or when the set button ( ) is pressed.

Note: When program on is set to "--:--", "DELE" flashes to confirm program has been deleted.

Countdown mode:
Press COUNTDOWN button, the countdown time will flash. Use arrows ( ) to adjust the countdown time. The switch will now count down for the time set every time the ON/OFF or door override is used. While switch is in countdown mode, the timer will run the programs normally but use the countdown time every time the ON/OFF override is selected.

RESET BUTTON

To set the switch back to factory settings, press and release the reset button with a toothpick. The reset button can be found behind the door in between the EXTRA PROGRAMS and the COUNTDOWN buttons. You can access the button by either removing the door or by holding the door at a 90 degree position and use a toothpick to depress the reset button.

DO NOT RETURN THIS PRODUCT TO THE STORE
Questions? Contact our U.S.-based Consumer Care at 1-855-698-8324, Monday–Friday, 7AM–8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.byjasco.com/support.

SPECIFICATIONS

Total ratings for both outlets:
120VAC, 60Hz
15A General/Resistive
1200W Tungsten
1200W Standard Ballast=
1/2HP Motor
5A or 600W Electronic Ballast/LED
Works with LED, CFL, incandescent and halogen bulbs.

RISK OF ELECTRICAL SHOCK

SHUT OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE INSTALLATION
DO NOT USE IN WET LOCATIONS
USE INDOORS ONLY

burn hazard RISK OF FIRE

DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.)
DO NOT EXCEED ELECTRICAL RATINGS
DO NOT USE TO CONTROL RECEPTACLES
USE COPPER WIRE ONLY WITH THIS DEVICE
TIGHTEN ALL CONNECTIONS TO 1-1.4 N-M (8.85 TO 12.39 LBF-IN.)
FOR SUPPLY CONNECTIONS, USE 14AWG OR LARGER WIRE RATED AT LEAST 75°C.
FOR GROUNDING LEAD, USE 12AWG OR LARGER WIRE RATED AT LEAST 75°C.

The Honeywell Trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
This product is manufactured by Jasco Products Company LLC.
This Jasco product comes with a 2-year limited warranty. Visit www.byjasco.com for warranty details.

Jasco Products Company LLC.
10 E. Memorial Road
Oklahoma City, OK 73114