Table of Contents
Advertisement
EN
ORIGINAL INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
The radio is intended for reception of analog broadcasting, and
streaming audio from BLUETOOTH enabled devices.
Through USB connection, the product can recharge USB devices.
Do not use the product for any other purpose.
WARNING! Read all safety warnings, instructions,
Failure to follow all instructions listed in this user manual may result
RADIO SAFETY WARNINGS
Never disassemble or modify the product in any way.
Do not use the product near water.
Do not place the product near any heat sources, such as radiators,
produce heat.
Do not cover ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
Do not place the product in closed bookcases or racks without
proper ventilation.
crushing or cutting of a battery, can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
liquid or gas.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING!
product damage due to a short circuit, never immerse your tool,
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG distributors offer to retrieve old batteries to
protect our environment.
Battery packs that have not been used for some time should be
recharged before use.
For an optimum lifetime, the battery packs have to be fully charged
after use.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and
away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
Battery pack protection
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress, the battery electronics turn off the product
automatically. To restart, turn the product off and then on again.
If the product does not start up again, the battery pack may have
discharged completely. Recharge the battery pack.
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national, and international provisions and regulations.
• Batteries can be transported by road without further requirement.
• Commercial transport of lithium-ion batteries by third parties is
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that the battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that the battery pack is secured against movement within
the packaging.
• Do not transport batteries that are cracked or leaking.
• Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 2.
1. USB charging port
2. Volume buttons
3. LCD display
4. Power button
5. BLUETOOTH mode button
6.
7. Left arrow button
8. Preset button
9. Right arrow button
10. Carrying handle
CONTROL BUTTONS
Press the power button to turn the product on and off.
• Press the BLUETOOTH button to enter BLUETOOTH mode. The
radio will begin searching for a previously paired device. "bt" will
begin blinking in the LCD display.
• If the paired device is not available or if there is no saved device
in the radio's memory, "bt" will blink continuously.
• To pair a device with the radio, select "AEG Jobsite Radio" on the
BLUETOOTH capable device.
• When the device has successfully paired with the radio, you
will hear an audible tone and "bt" will stop blinking in the LCD
display.
• Once paired, the radio will automatically reconnect to the same
device when in BLUETOOTH mode.
• Once the device has successfully paired with the radio, use the
controls on the BLUETOOTH capable device to move through
tracks and control volume, or press the arrow buttons on the
radio to go to the previous or next track. Press the PRESETS
NOTE: These controls may not be supported by the
• If a device disconnects with the radio, the BLUETOOTH indicator
will flash until another device pairs to the radio.
• To disconnect the current device to allow connection to another
BLUETOOTH enabled device, press and hold the BLUETOOTH
button for 3 seconds. The radio will then be in pair mode and can
be connected to a different device.
NOTE: The product will turn off in half an hour if no audio has been
streamed in BLUETOOTH mode. Turn on the product to resume
operation.
In BLUETOOH mode: Press the arrow buttons on the radio to go to
the previous or next track.
In radio mode: Press the left arrow button to tune to a lower
frequency. Press the right arrow button to tune to a higher
one frequency step at a time. Press and hold the desired arrow
button for one second to tune to the next frequency with clear
reception.
The memory feature saves up to 20 frequencies as presets in the
radio's memory. You can save 10 frequencies in FM mode and 10
in AM mode.
To store a frequency in memory:
• Tune to the frequency you want to save.
• Press and hold the PRESETS button for 1 second. A memory
location number will blink on and off.
• Press either arrow button to scroll through the preset positions.
• Press the PRESETS button to store the frequency in the selected
memory location.
EN
DE
FR
IT
ES
PT
NL
DA
NO
SV
FI
EL
TR
CS
SK
PL
HU
SL
HR
LV
LT
ET
RU
BG
RO
MK
UK
AR
7
Advertisement
Table of Contents
