•
Check for damage to the appliance, parts or accessories which
may have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Date Code Position (Fig. A)
The date code
31
, which also includes the year of manufacture,
is printed into the housing.
Example:
Year and Week of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Jack plug
1
Plug port
2
Drip tray
3
Drip tray cover
4
Drip tray cover finger hole
5
Bottle platform
6
Straws (6)
7
Straw locks (6)
8
Straw tips (6)
9
Straw slots (6)
10
Straw plug (6)
11
Straw plug notch (6)
12
Bottle stoppers (6)
13
Power switch
14
Strength LEDs (4)
15
Bottle LEDs (6)
16
Glass shelf
17
Tower
18
Shaker LED
19
Capsule (not included)
20
Capsule holder
21
Capsule holder lid
22
Capsule cup
23
Capsule tab
24
Strength selector dial
25
Mix button
26
Party mode button
27
Cleaning mode button
28
Water bottle
29
Straw cleaner
30
Date code
31
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT let children come into contact with the appliance.
Supervision is required when inexperienced operators use
this appliance.
2021 XX XX
Intended Use
This appliance is intended for residential use only for mixing
cocktails by adults of legal drinking age.
DO nOT let children come into contact with the appliance.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn appliance off and disconnect appliance
from power source before making any adjustments
or removing/installing attachments or accessories.
An accidental start-up can cause injury.
Installing Cord (Fig. B)
1. Place the cocktail maker upright on a flat, level,
stable surface.
2. Insert the jack plug
1
3. Plug the other end of the cord into an outlet.
Installing Coaster (Fig. C)
1. Place the drip tray cover into the drip tray
and slanted corners of the cover line up with the rounded
and slanted corners of the drip tray.
2. Ensure the cover sits fully inside the drip tray.
3. To remove the cover, lift from the drip tray cover finger hole
Installing Bottles (Fig. D)
WARNING: Only use water in the supplied water bottle.
Use of other liquids or substances in the water bottle may
result in damage to the appliance.
CAUTION: Avoid spills while installing bottles.
nOTE: It is recommended to use 750 ml bottles or smaller to
ensure all bottles sit on the bottle platform
off the platform.
nOTE: Bottles must fit between the bottle platform and the top
of the cocktail maker while standing.
1. Slide a straw
7
into a bottle so the straw tip
bottom of the bottle.
2. Slide the bottle stopper
in the top of the bottle.
3. Ensure the straw lock
8
4. Align the straw plug notch
5. Slide the straw plug
11
allowing the bottle to sit freely in its designated space.
Ensure the straw plug is fully seated in the slot
6. To lock it into place, push the straw lock down until it clicks.
Ensure the lever is fully down.
7. Repeat for all bottles.
IMPORTanT: Bottles must be placed in their designated space
to ensure the correct drink is dispensed. Names of the liquids are
located in each spot, indicating the appropriate liquid.
IMPORTanT: The following are the only liquids that should be
used with the appliance.
•
Water
of the cord into the plug port
3
so the rounded
6
without hanging
9
sits on the
13
down the straw until it sits fully
is up.
12
with the straw slot
all the way into the straw slot,
EnGLIsH
2
.
5
.
10
.
17