Table of Contents
Advertisement
Quick Links
Power Distribution Center
Note: This product requires Output Breakers and Cord Sets, sold separately. See Section 5.1 for ordering information.
1 – Introduction
2 – Important Safety Instructions
3 – Features
4 – Cabinet Installation
4.1 Preparation
4.2 Unpacking
4.3 Placement
4.4 Leveling
4.5 Ground Connection
5 – Wiring Installation
5.1 Preparation
5.2 Installing Breakers
5.3 Installing Cord Sets
5.4 Wiring Breakers
5.5 Wiring Input Power
5.6 Powering Up
5.7 Powering Down
6 – Storage & Service
7 – Warranty and Warranty Registration
Owner's Manual
Model: SUDC208V42P
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2010 Tripp Lite. All rights reserved.
1
2
2
4
5
5
5
6
6
7
7
7
9
9
10
11
11
11
12
12
Advertisement
Table of Contents
Related Manuals for Tripp Lite SUDC208V42P
Summary of Contents for Tripp Lite SUDC208V42P
- Page 1 5.4 Wiring Breakers 5.5 Wiring Input Power 5.6 Powering Up 5.7 Powering Down 6 – Storage & Service 7 – Warranty and Warranty Registration 1111 W. 35th Street, Chicago, IL 60609 USA www.tripplite.com/support Copyright © 2010 Tripp Lite. All rights reserved.
-
Page 2: Important Safety Instructions
• Inspect the shipping container and the Distribution Center for shipping damage. If you determine that the Distribution Center has been damaged during shipping, or if anything appears to be missing, contact Tripp Lite for assistance. Do not use the Distribution Center if it is damaged. - Page 3 2 – Important Safety Instructions continued DANGER! LETHAL HIGH VOLTAGE HAZARD! All wiring must be performed by a qualified electrician, in accordance with the warnings in this manual and all applicable electrical and safety codes. Incorrect wiring may cause serious personal injury and property damage. Wiring Warnings •...
- Page 4 42-Pole Circuit Breaker Panel: Output branch circuit breakers (sold separately) snap into this panel. The output cord sets (sold separately) will be wired here. Warning: Use Tripp Lite breakers and cord sets only. Main Circuit Breaker: The 3-phase power source will be wired to this breaker.
-
Page 5: Cabinet Installation
Remove the heavy plastic bag surrounding the Distribution Center. Examine the Distribution Center for any damage or loose parts. Confirm that all parts are present. If anything is missing or damaged, contact Tripp Lite for assistance. Do not attempt to use the Distribution Center if it has been damaged. - Page 6 4 – Cabinet Installation continued Use a 13 mm open-end wrench to remove the shipping brackets at the front and rear of the Distribution Center. Be extremely careful, as the Distribution Center could shift unexpectedly after bracket removal. Save the brackets and bracket hardware for later use. Position at least one person at the front of the Distribution Center and one person at the rear of the Distribution Center.
-
Page 7: Ground Connection
Routing output cord sets from the top of the Distribution Center to your racks and PDUs should be managed systematically, with proper data and power cable segregation. Tripp Lite offers a full line of external cable management accessories (sold separately), including SRCABLELADDER, SRCABLETRAY and SRCABLETRAYEXP. -
Page 8: Installation
5 – Installation continued Available Cord Sets 120V, Single-Phase with L5-20R Connector. Use with compatible PDUs, including these Tripp Lite models: PDU1220T, PDU1420T, PDUNV, PDU40TDUAL, PDUMV20, PDUMV40, PDUMH20, PDUMNH20, PDUMNV20, PDUMV20NET, PDUMH20AT and PDUMH20ATNET. Tripp Lite # Total Length ROJ Length... -
Page 9: Installing Breakers
5 – Installation continued WARNING! Before wiring make sure that all breakers (including the Distribution Center’s Main Breaker) are in the OFF position and that the 3-phase power source is de-energized! 5.2 Installing Breakers Open the Distribution Center’s front door to access the breaker box. Remove 6 screws from the breaker box front panel, then remove the panel and set it aside. - Page 10 5 – Installation continued After attaching your cord sets, route and attach these power cables From to your equipment racks. Distribution From PDU Center • Install the optional SRCABLELADDER, SRCABLETRAY and SRCABLETRAYEXP onto your racks for easier cable routing and management. •...
-
Page 11: Powering Down
NEC and all other applicable electrical and safety regulations. The electrician may wish to refer to Tripp Lite’s 3-Phase Domestic Site Planning Data Sheet, downloadable at www.tripplite.com. Input power to the Distribution Center’s main input must be 3-phase, 4 wire + ground from a 120/208V 3-phase source. The use of ferrules on stranded wire is recommended. -
Page 12: Storage And Service
WARRANTY REGISTRATION Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary.