Summary of Contents for Fenix Imvico PPCF17TS Series
Page 1
PPCF17TS SERIES SAW TECHNOLOGY PANEL PC FENIX IMVICO, S.A. Manual de Instalación del Panel PC SAW Panel PC SAW Installation Manual Version 1.0...
Page 2
Manual de Instalación / Installation Manual Revision: Version 1.0 09/2009 Página Tipo Revisión Antes del cambio Después del cambio Page Revision type Before change After change 2/71...
Manual de Instalación / Installation Manual 1 – INTRODUCCIÓN Gracias por confiar en un producto Fenix Imvico. El producto que tiene en sus manos es un equipo compacto compuesto de una placa SBC (single board computing) de altas prestaciones, una pantalla plana TFT-17”...
Manual de Instalación / Installation Manual Especificaciones del TFT TECNOLOGÍA Matriz 17” TFT ÁREA DE VISIÓN 337.9mm x 270.3mm BRILLO 300cd/m2 RESOLUCIÓN MÁXIMA SXGA 1280 x 1024 CONTRASTE 700:1 COLORES 16.2 Millones ÁNGULO DE VISIÓN 130º H, 120º V DIMENSIONES (H x W x D) (mm) 425 x 334 x 66.3 MTF DE LAS LÁMPARAS 50.000 horas Especificaciones del Panel Táctil...
Manual de Instalación / Installation Manual 4 – DESCRIPCIÓN GENERAL 1: Botón Reset 2: Led encendido 3: Botón On/Off 4: Conector On/Off remoto 5: Conector audio MIC IN 6: Conector audio LINE OUT 7: Conector ratón PS/2 8: Conector puerto paralelo DB25 9: 3 x Conectores puerto serie DB9 10: Conector Ethernet RJ-45 11: Conmutador de fuente de alimentación 115/230 VAC...
Manual de Instalación / Installation Manual 5 – PRECAUCIONES DE SEGURIDAD 1. Antes de instalar, mover o abrir el panel PC, asegúrese de que la corriente está apagada y el cable de red desconectado. 2. Siga las precauciones sobre descargas electrostáticas cuando manipule componentes internos del panel PC.
Manual de Instalación / Installation Manual 6 – INSTALACIÓN En la caja del panel PC encontrará los siguientes componentes: – Panel PC completamente ensamblado. – Soportes metálicos – Bandas anti-polvo. – Cable de red. – Guía rápida. Para poder instalar el panel PC en una estructura fija que lo soporte siga atentamente los siguientes pasos: Fije el Panel PC 1.
Page 11
Manual de Instalación / Installation Manual fig 2. Panel PC montado sobre vigas traseras. Opción A fig 3. Panel PC montado sobre vigas traseras. Opción B fig 4. Panel PC montado sobre pared frontal. Opción A fig 5. Panel PC montado sobre pared frontal. Opción B Notas importantes: •...
Manual de Instalación / Installation Manual 2. Practicar una abertura del tamaño del área visible de la pantalla y realizar las fijaciones correspondientes si se ha elegido el montaje sobre pared frontal. 3. Pegar la tiras anti-polvo cerca del borde interior de la abertura realizada. Deje al menos 1mm entre el borde y la tira de manera que al presionar el panel PC sobre la pared, cuando las tiras se compriman y expandan a lo ancho, no lleguen a asomar por la abertura.
Manual de Instalación / Installation Manual 8. Conectar los cables de comunicación cables si fuera necesario (Ethernet, serie, paralelo y USB). 9. Conectar el cable de red AC al panel PC y al enchufe correspondiente. Es aconsejable instalar un interruptor automático de protección entre el panel PC y la fuente principal de tensión AC. Instalar el sistema operativo Excepto requerimiento especial el disco duro contendrá...
7 – DIMENSIONES MECÁNICAS fig 6. Medidas exteriores. Unidades en mm.
Page 15
fig 7. Agujeros de fijación horizontales. Unidades en mm. fig 8. Agujeros de fijación verticales. Unidades en mm. fig 9. Dimensiones de soportes. Unidades en mm.
Page 16
Manual de Instalación / Installation Manual fig 10. Aberturas a practicar en el frontal en función de la opción de montaje. Unidades en mm. 16/71...
Manual de Instalación / Installation Manual 8 – OPCIONES DE CONFIGURACIÓN DE LA BIOS Iniciando el Programa Setup La AwardBIOS™ se ejecuta tan pronto se arranca el equipo. La BIOS captura la información del sistema contenida en la memoria CMOS y empieza a verificar y configurar el sistema. Una vez concluido este proceso, la BIOS intenta arrancar un sistema operativo contenido en el primer dispositivo marcado como “dispositivo arrancable”...
Manual de Instalación / Installation Manual Menú Principal Al entrar en el programa BIOS, aparecerá el menú siguiente en pantalla. Las pantallas mostradas en esta sección no tienen por que ser exactamente iguales a las que usted tenga. Standard CMOS Features A continuación se muestra el menú...
Page 19
Manual de Instalación / Installation Manual Selección del Menú Principal Parámetro Opciones Descripción Date and Time Configura la fecha y hora del sistema IDE Primary Master Ver opciones de IDE Primary Slave Pulsar <Enter> para entrar el submenú de “Configuración de IDE Secondary Master opciones detalladas Adaptador IDE”...
Manual de Instalación / Installation Manual Advanced BIOS Features Esta sección permite configurar las operaciones principales del sistema como la secuencia de arranque, comportamiento del teclado, opciones de seguridad, etc. CPU Feature Esta opción permite configurar la función de gestión térmica de la CPU aunque en realidad sólo hay una opción que es “Thermal Monitor 1”.
Page 21
Manual de Instalación / Installation Manual La BIOS cargará el sistema operativo de uno de los dispositivos de abajo en la secuencia seleccionada. Parámetro Descripción LS120 Unidad LS120 HDD-0~4 Unidad de Disco Duro 0, 1, 2, 3, 4 SCSI Unidad SCSI CDROM Unidad de CDROM ZIP100...
Manual de Instalación / Installation Manual Selecciona si el sistema operativo correrá con más de 64MB de RAM de la memoria del sistema. Non-OS2: Deshabilita SO para más de 64 MB DRAM (por defecto). • OS2: Habilita SO para más de 64 MB DRAM. •...
Page 23
Manual de Instalación / Installation Manual • Active to Precharge Delay Esta opción es el intervalo mínimo entre Activo y Precarga. • • • DRAM RAS# to CAS# Delay Esta opción permite insertar un retraso entre las señales de activación de dirección de fila y de columna.
Page 24
Manual de Instalación / Installation Manual Delay Prior to Thermal Cuando la temperatura del sistema es alta puede ralentizar el tiempo de acceso a DRAM durante 4 min – 32 min. 4 Min. • 8 Min. • 16 Min. • 32 Min (por defecto).
Manual de Instalación / Installation Manual Número de Panel Formato de Salida Profundidad de Color Tipo de Canal LVDS 640 x 480 18-bit Single 800 x 600 18-bit Single 1024 x 768 24-bit Single 4 (por defecto) 1280 x 1024 18-bit Dual 1400 x 1050...
Page 26
Manual de Instalación / Installation Manual OnChip IDE Device Parámetro Opciones Descripción El chipset contiene un interface PCI IDE con soporte para 2 canales IDE. Seleccione “Enabled” para On-Chip Primary PCI IDE Enabled activar interface primario/secundario. On-Chip Secondary PCI IDE Disabled Seleccione “Disabled”...
Manual de Instalación / Installation Manual Parámetro Opciones Descripción Enabled (defecto) USB Controller Este parámetro permite configurar el controlador USB. Disabled Enabled Este parámetro permite configurar el controlador USB USB 2.0 Controller Disabled (defecto) 2.0. Enabled Este parámetro permite configurar teclado USB del USB Keyboard Support Disabled (defecto) sistema.
Page 28
Manual de Instalación / Installation Manual ACPI Function Este parámetro permite habilitar/deshabilitar la función ACPI. Disabled. • Enabled (por defecto). • ACPI Suspend Type Este parámetro selecciona que tipo de suspensión ACPI se usará. • S1(POS) (por defecto) • S3(STR) •...
Page 29
Manual de Instalación / Installation Manual Video Off Method Determina la manera en que el monitor se apaga. • Blank Screen • V/H SYNC+Blank • DPMS (por defecto) Video Off In Suspend Determina la manera en que el monitor se apaga. •...
Manual de Instalación / Installation Manual Primary/Secondary IDE 0/1,COM,LPT PORT, PCI PIRQ[A-D]# Los eventos “Reinicia Temporizador Global” son eventos E/S cuya ocurrencia puede evitar que el sistema entre en el modo de ahorro de energía o pueden “despertar” al sistema de este modo. En efecto, el sistema permanece alerta por cualquier cosa que ocurra a un dispositivo que ha sido configurado como habilitado, incluso cuando el sistema esta en modo apagado.
Manual de Instalación / Installation Manual CPU Smart Fan Temperature Este valor sumado a la tolerancia es el rango de temperatura que el sistema intentará mantener, por tanto cuando la temperatura de la CPU suba por encima del margen superior, el ventilador girará más rápido para enfriarla y cuando la temperatura caiga por debajo del margen inferior la velocidad del ventilador disminuirá.
Manual de Instalación / Installation Manual Auto Detect PCI Clk Este parámetro permite habilitar/deshabilitar la auto detección del reloj PCI. Disabled • Enabled (por defecto) • Spread Spectrum Este parámetro permite ajustar valores extremos de pulso para los test EMI. Disabled •...
Manual de Instalación / Installation Manual Set Supervisor Password Se puede configurar la contraseña de supervisor que permite cambiar las opciones del programa “Setup”. El programa pedirá que se introduzca y posteriormente confirme una contraseña de hasta 8 caracteres. La contraseña introducida sobrescribirá cualquier contraseña previa en la memoria CMOS. Si se pulsa <Esc>...
Manual de Instalación / Installation Manual Ver “Configurar contraseña de Supervisor” para ver como operar con contraseñas. Save & Exit Setup Guarda los cambios en la memoria CMOS y sale del programa “Setup”. Pulse <Y> para guardar los cambios en la memoria CMOS.
Manual de Instalación / Installation Manual 9 – CONTROLADORES Sistemas Operativos El panel PC soporta tanto Windows 2000/XP como Linux. En el primer caso se proporcionan los controladores de todos los dispositivos hardware que así lo requieren. En el caso de Linux, las distribuciones más populares (Ubuntu, OpenSUSE, etc.) incluyen controladores para la mayoría de dispositivos excepto para la pantalla táctil por lo que sólo se proporciona el controlador para éste.
Page 36
Manual de Instalación / Installation Manual > mkdir /usr/local/Gentouch_S > cp <setup-distribution-folder>/* /usr/local/Gentouch_S/ III. > /usr/local/Gentouch_S/GT_service start 3. Calibración ejecute: >./GTscal /dev/ttyS3 (/dev/ttyS3 es para el puerto interno COM4) 4. Desintalación ejecute: > ./uninstall 5. Configuración a) Cambiar parámetros de configuración automáticamente. ejecute: >./GenpanelS Si ha seguido la instalación automática debe encontrar un acceso directo a GenpanelS en el...
Manual de Instalación / Installation Manual 10 – COMO REALIZAR UN PEDIDO PPCF17S -DP : Pantalla Anti-polvo -WP: Pantalla resistente al agua (IP65) y cristal anti-vandalismo Versión especial blanco: Tipo estándar xxx: Opciones y versiones especiales (sólo bajo acuerdo) 37/71...
Manual de Instalación / Installation Manual 11 – DIAGNÓSTICO DE ERRORES Problema Causa Solución Sistema sin energía. LED de 1. El cable de red está 1. Asegúrese de que el cable de red está bien encendido no se ilumina. El desconectado.
Manual de Instalación / Installation Manual 1 – INTRODUCTION Thanks for having chosen a Fenix Imvico product. The product you have in your hands it is a highly compact equipment that comprises a highly featured mainboard with a flat 17” TFT screen and a touch screen that uses surface acoustic wave technology.
Manual de Instalación / Installation Manual 5 – SAFETY PRECAUTIONS 1. Before installing, moving or opening the panel PC, ensure that the power is off and the power cord is unplugged. 2. Observe ESD precautions when manipulating the components of the panel PC. 3.
Manual de Instalación / Installation Manual 6 – INSTALLATION The panel PC retail box should contain the following components: – Panel PC fully assembled. – Metal brackets. – Dust-proof stripes. – Power cord. – Quick guide. In order to install the panel PC onto its supporting structure please follow carefully the steps below: Fix the Panel PC 1.
Page 45
Manual de Instalación / Installation Manual fig 2. Panel PC fixed to rear crossbeam. Option A fig 3. Panel PC fixed to rear columns. Option B fig 4. Panel PC fixed to frontal wall. Option A fig 5. Panel PC fixed to frontal wall. Option B Important notes: •...
Manual de Instalación / Installation Manual 3. Stick the dust-proof strips close to the internal opening edge. Leave at least 1mm between the edge and the strip as it will expand as it is being compressed by the frame of the panel PC. 4.
7 – MECHANICAL DIMENSIONS fig 6. External dimensions. All dimensions are in millimeters.
Page 48
fig 7. Horizontal fixing holes. All dimensions are in millimeters. fig 8. Vertical fixing holes. All dimensions are in millimeters. fig 9. Fixing bracket dimensions. All dimensions are in millimeters.
Page 49
Manual de Instalación / Installation Manual fig 10. Openings to make on the front wall depending on the fixing option. All units in mm. 49/71...
Manual de Instalación / Installation Manual 8 – BIOS CONFIGURATION OPTIONS Starting Setup The AwardBIOS™ is running as soon as the power is switched on. The BIOS reads the system information contained in the CMOS memory and starts checking out and configuring the system. When finished, the BIOS will try to boot an operating system from the first booting device specified, if it does not find an OS it will jump the the next one.
Manual de Instalación / Installation Manual Main Menu When you enter the AwardBIOS™ CMOS Setup Utility, the following menu will show up on the screen. Take into account that screens shown in this section do not have to match exactly with what you have.
Manual de Instalación / Installation Manual Main Menu Selection Item Options Description Date and Time Set the system time IDE Primary Master IDE Primary Slave See “IDE Adapter Press <Enter> to enter the sub menu of IDE Secondary Master Setup” Options detailed options IDE Secondary Slave EGA/VGA...
Page 53
Manual de Instalación / Installation Manual CPU Feature This item allows you to setup the CPU thermal management function although in fact there is just one option which is Thermal Monitor 1. Virus Warning If this function is enabled for a particular hard disk drive and someone attempt to write data into the boot area, BIOS will show a warning message on screen and alarm will beep.
Manual de Instalación / Installation Manual Boot Up NumLock Status Select power on state for NumLock. On: Enable NumLock (default). • Off: Disable NumLock. • • Gate A20 Option Select if chipset or keyboard controller should control Gate A20. Normal: A pin in the keyboard controller controls Gate A20. •...
Page 55
Manual de Instalación / Installation Manual DRAM Timing Selectable This item allows you to select the DRAM timing value by SPD data or Manual by yourself. Manual. • By SPD (default). • CAS Latency Time This item controls the time delay (in clock cycles - CLKs) that passes before the SDRAM starts to carry out a read command after receiving it.
Page 56
Manual de Instalación / Installation Manual System BIOS Cacheable This feature is only valid when the system BIOS is shadowed. It enables or disables the caching of the system BIOS ROM at F0000h-FFFFFh via the L2 cache. This greatly speeds up accesses to the system BIOS.
Page 57
Manual de Instalación / Installation Manual Boot Display Allows selection of the boot display device. The choices are: CRT. • LFP (default). • CRT+LFP. • EFP. • • CRT+EFP. • CRT+TV. • Panel Scaling This item is enabled as the onboard VGA is used. Auto (default).
Manual de Instalación / Installation Manual Integrated Peripherals Use this menu to specify your settings for integrated peripherals. OnChip IDE Device Item Options Description The chipset contains a PCI IDE interface with On-Chip Primary PCI IDE Enabled support for two IDE channels. Select Enabled to On-Chip Secondary PCI IDE Disabled activate the primary/secondary IDE interface.
Page 59
Manual de Instalación / Installation Manual Ultra DMA implementation is possible only if IDE Primary Master UDMA your IDE hard drive supports it and the IDE Primary Slave UDMA Auto operating environment includes a DMA driver IDE Secondary Master UDMA Disabled (Windows 95 OSR2 or a third-party IDE bus IDE Secondary Slave UDMA...
Manual de Instalación / Installation Manual Item Options Description Onboard Serial Port 1 Disable, 3F8/IRQ4 Onboard Serial Port 2 Select an address and corresponding interrupt 2F8/IRQ3, 3E8/IRQ4 Onboard Serial Port 3 for the first and second serial ports. 2E8/IRQ3 Onboard Serial Port 4 Disabled, 378/IRQ7, Select a matching address and interrupt for Onboard Parallel Port...
Page 61
Manual de Instalación / Installation Manual Run VGABIOS if S3 Resume When ACPI Suspend Type is set to S3 or S1&S3, users can select the options in this field. Selecting “Yes” allows BIOS to call VGABIOS to initialize the VGA card when system wakes up (resumes) from S3 sleep state.
Manual de Instalación / Installation Manual Power On By Ring This determines whether the system boot up if there’s an incoming call from the Modem. Disabled. • Enabled (default). • Resume By Alarm This function is for setting date and time for your computer to boot up. Disabled (default).
Manual de Instalación / Installation Manual CPU Smart Fan Temperature This value plus the tolerance is the system will try to keep so when the CPU temperature goes up Temp+Tolerance, the fan will start to run faster to cool it down and when the temperature goes below Temp-Tolerance the fan will slow down.
Manual de Instalación / Installation Manual Auto Detect PCI Clk This item allows you to enable/disable auto detect PCI Clock. Disabled. • Enabled (default). • Spread Spectrum This item is to adjust extreme values of the pulse for EMI test. Disabled.
Manual de Instalación / Installation Manual Set Supervisor Password You can set supervisor password which allows to enter/change the options of setup menus. You will be prompted to type and after to confirm a password, up to eight characters in length. The password typed will overwrite any previous password from CMOS memory.
Manual de Instalación / Installation Manual Save & Exit Setup Save CMOS changes to CMOS and exit setup. Enter <Y> to save the settings into CMOS. The BIOS will boot up the system according to the saved Setup settings. Quit Without Saving Reject all CMOS changes and exit setup.
Manual de Instalación / Installation Manual 9 – SOFTWARE DRIVERS Panel PC supports Windows 2000/XP and Linux. In the first case the required hardware drivers are provided. In case of Linux, the most popular distributions (Ubuntu, OpenSUSE, etc.) include drivers for the most of hardware devices in the panel PC with the exception of touch screen, therefore only the driver for this device it is provided.
Page 68
Manual de Instalación / Installation Manual 3. Calibrate run: >./GTscal /dev/ttyS3 (/dev/ttyS3 is for internal port COM4) 4. Uninstall run: > ./uninstall 5. Setting a) Change setting automatically run: >./GenpanelS If you have run automatic setup there will be a link of GenpanelS at root user's Desktop. The change of touchscreen's setting will take effect by clicking the button "apply"...
Manual de Instalación / Installation Manual 10 - HOW TO ORDER PPCF17S -DP : DustProof glass -WP: WaterProof (IP65) anti-vandalism glass Special version blank: Standard type xxx: Options and custom-made type (under agreement only) 69/71...
Manual de Instalación / Installation Manual 11 – TROUBLESHOOTING Problem Cause Solution No power to the system. Fan inside 3. Power cable is unplugged. 1. Make sure power cable is securely plugged in. power supply does not turn on. 4. Defective power cable. 2.