Sony XR-CA350X Installation/Connections

FM /AM Casset t e
Car St ereo
Inst allat ion/Connect ions
Inst allat ion/Connexions
XR-CA350X
Sony Corporation © 2003
1
1
4
Equipm ent used in illust rat ions (not supplied)
Appareils ut ilisés dans les illust rat ions (non fournis)
Front speaker
Haut-parleur frontal
Rear speaker
Haut-parleur arrière
Downloaded from: https://www.usersmanualguide.com/
3-246-853-11 (2)
Printed in Malaysia
2 3
× 4
5
× 2
Pow er amplifier
Amplificateur de puissance
CD/ M D changer
Changeur de CD/ M D
2
A
B
BUS AUDIO IN
BUS CONTROL IN
*
Source selector
*
Sélecteur de source
XA-C30
Caut ions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g., seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground w ires to a common ground
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the pow er supply cord (yellow )
•When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Part s Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar
3 from the unit. For details, see "Removing
the protection collar and the bracket (4)" on
the reverse side of the sheet.
• Keep the release keys 5 for future use as
they are also necessary if you remove the
unit from your car.
Caut ion
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Catch
Note
Bef ore inst alling, make sure t hat t he cat ches on
bot h sides of t he bracket 1 are bent inw ards 2 mm
( 3 / in). If t he cat ches are st raight or bent out w ards,
32
t he unit w ill not be inst alled securely and may spring
out .
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
* not supplied
* non f ourni
Connect ion exam ple (2)
Notes ( 2 -B-
)
• Be sure t o connect t he ground cord bef ore
connect ing t he amplif ier.
• If you connect an opt ional pow er amplif ier and do
not use t he built -in amplif ier, t he beep sound w ill
be deact ivat ed.
Tip ( 2 -B-
)
For connect ing t w o or more CD/M D changers, t he
source select or XA-C30 (opt ional) is necessary.
Connect ion diagram (3)
1 To a metal surface of the car
First connect t he black ground lead, t hen
connect t he yellow and red pow er input leads.
2 To the pow er antenna control lead or pow er
supply lead of antenna booster amplifier
Notes
• It is not necessary t o connect t his lead if t here
is no pow er ant enna or ant enna boost er, or
w it h a manually-operat ed t elescopic ant enna.
• When your car has a built -in FM /AM ant enna in
t he rear/side glass, see " Not es on t he cont rol
and pow er supply leads."
3 To AM P REM OTE IN of an optional pow er
amplifier
This connect ion is only f or amplif iers. Connect ing
any ot her syst em may damage t he unit .
4 To the +12 V pow er terminal w hich is energized
in the accessory position of the ignition key
sw itch
Notes
• If t here is no accessory posit ion, connect t o t he
+12 V pow er (bat t ery) t erminal w hich is
energized at all t imes.
Be sure t o connect t he black ground lead t o a
met al surf ace of t he car f irst .
• When your car has a built -in FM /AM ant enna in
t he rear/side glass, see " Not es on t he cont rol
and pow er supply leads."
5 To the +12 V pow er terminal w hich is energized
at all times
Be sure t o connect t he black ground lead t o a
met al surf ace of t he car f irst .