Advertisement
Quick Links
Advertisement
Summary of Contents for Accelus Robotics MeteorCNC
- Page 1 MeteorCNC - Made In India User Manual v1.7...
- Page 2 CNC Controller Specialist Index Topic Page No. Introduction Wiring Details Menu System KeyPad Details...
- Page 3 CNC Controller Specialist Ch 1 : Introduction MeteorCNC providing upto four axis (X,Y,Z & 4 ) upto 550khz Differential Pulse & Direction Outputs for smooth motion. With 16 digital inputs & 8 digital outputs, one analog output(0-10v) signal for spindle speed control & one optically isolated quadrature encoder input with index.
- Page 4 CNC Controller Specialist Ch 2 : Wiring Details P a g e...
- Page 5 CNC Controller Specialist 2.1 Inputs MeteorCNC provides total 16 Isolated Inputs. User can use either NPN or PNP signal inputs as shown in Fig.2.1.1. IP1 to IP16 are Input led indicators. Fig. 2.1.1 Details of Inputs are given below. Input No.
- Page 6 CNC Controller Specialist 2.2 Outputs MeteorCNC provides total 8 isolated outputs. Each output provide up to 2A current & 24v out as shown in Fig 2.2.2.Op1 to Op8 are Output led indicators. Fig 2.2.2 Details of Outputs are given below.
- Page 7 CNC Controller Specialist 2.3 Analog Output MeteorCNC provides one analog output which vary from 0-10v.This analog output will help to run the spindle with on set frequency. To trigger VFD MeteorCNC have dedicated output as Op3 as shown in Fig.2.3.1 Fig.2.3.1 2.4.Differential Pulse &...
- Page 8 Drive’s end. 2.6. Supply Voltage MeteorCNC require 24v dc to start its operation. Please provide supply to both the side of controller. EX5 & EX24 led indicates external 5v & 24v working. 3.3v, 5v & M24 indicates 3.3v,5v & 24v working.
- Page 9 CNC Controller Specialist Ch 3 : Menu System MeteorCNC provides below menu in its systems. 1. MeteorCNC 2. Operations 3. Breakpoint Restore (Breakpoint Rstr) 4. Job Setup 5. Machine Setup 6. Diagnosis 7. Backup / Restore 1. MeteorCNC Machine status is shown in this.
- Page 10 CNC Controller Specialist In this user can see the file from inserted USB pen drive. User can USB Files copy .NGC or .Tap file from pen drive & paste it in internal memory of controller. Goto WCS Org Goto WCS All Goto WCS All : This will send X,Y &...
- Page 11 3. Breakpt Rstr (Breakpoint Restore) This functionality used to saved line number & axis position when power goes off. MeteorCNC will store the data in following conditions - During power failure in between running the program. - User stop the design with stop button from hand handle or By pressing Emergency Stop.
- Page 12 CNC Controller Specialist Job Spd & Dist User will defined the goto WCS speed. Goto WCS Spd Ct. Jog High User will defined the continuous High Jog speed. User can change the mode by pressing Jog Spd button (number 5). User will defined the continuous Medium Jog speed.
- Page 13 CNC Controller Specialist Mirror Gcode X Mirror Mirror This will flip X-side Gcode. Y Mirror This will flip Y-side Gcode. Feed Remp Turn this ON to bypass the program feed. Ctrl Feed Feed value taken as per the setting. This value will be used as feed if Ctrl feed feature is ON. Feed Turn this ON to bypass the program Spindle Speed.
- Page 14 CNC Controller Specialist Tool Setup Set the tool length offset for 50 tools for the machine Z offset configuration. This will be used when tool compensation will be applied by G43. Set the tool diameter for 50 tools for the machine Tool Diameter configuration.
- Page 15 X-axis 1. Pulse / mm : This is scaling factor of number of pulses to be generated by the MeteorCNC to move axis by 1mm. please refer below examples for better understanding. Eg.1 : Drive PPR : 4000 & Ball screw pitch : 5 mm Pulse/mm (scale) = Drive PPR / Ball screw pitch = 4000/5 = 800 Eg.2 : Drive PPR : 4000 &...
- Page 16 CNC Controller Specialist Eg.3 : Drive PPR : 4000 & 1:4 ratio given of axis Pulse/mm (scale) = Drive PPR * ratio = 4000 * (1/4) = 1000 2. Backlash : Backlash compensation value cab be used to make up for small deficiencies in the hardware used to drive an axis.
- Page 17 User can change the machine setup password if he knows the old Change password password. 6. Diagnosis Shows the current program version which is running in MeteorCNC. Version This is used diagnosis the handle’s keys are properly working or not. Keypad Check 15 |...
- Page 18 CNC Controller Specialist This is used to check the controller’s status like E-stop, Machine Machine State Status , Current WCS, Tool offset, Tool number etc. G52 Offset G52 offset of X,Y and Z axis for selected WCS. G92 Offset G92 offset of X,Y and Z axis. G43 Offset Length offset of X,Y and Z axis.
- Page 19 CNC Controller Specialist Ch 4 : KeyPad Details 17 | P a g e...
- Page 20 CNC Controller Specialist Key Name Function Key Icon X+ / number input 6 X-axis positive jog;Input number of 6. Shift + key 6 shortcut for Mirror Code X- / number input 4 X-axis negative jog;Input number of 4. Y+ / number input 8 Y-axis positive jog;Input number of 8.
- Page 21 CNC Controller Specialist Spindle on/Spindle Off Manually turn On /Off spindle; Goto position X=0,Y=0,A=0 / Go to Position Origin of WCS for X,Y,A Set position X=0 Y=0 A=0 / axis; Shift + XYA=0 to set Origin of WCS in number input 0; selected coordinate system for X,Y,A axis.