Advertisement
8)
The power indicator will illuminate and will flash every second whilst the unit
pre-heats.
9)
Allow the handheld garment steamer to warm up. This can take up to 35 seconds.
10) When the power indicator stops flashing and illuminates solid, the appliance is
ready to use.
11) Stand the handheld garment steamer on its base on a flat, stable and heat-
resistant surface.
12) Position the steam nozzle away from you and others.
13) Press and hold the +/- steam setting button and steam button
for 5 seconds.
14) The handheld garment steamer will enter a cleaning cycle for 1 minute. The
steam mode indicator lights will blink quickly whilst in cleaning mode.
15) Once the cleaning cycle is complete, the unit will automatically enter drying mode
for 20 seconds. The drying cycle is complete once the steam mode indicator lights
stops blinking.
16) The steam setting will return to the previous selection.
Care & cleaning
Warning: Do not use harsh abrasives, chemical cleaners or solvents to clean the
exterior of your handheld garment steamer. Do not immerse the appliance or power
cord and plug in water or any other liquid.
Allow your handheld garment steamer to completely cool down and wipe the press
plate and exterior with a soft damp cloth. Wipe dry before storing.
After sales service and replacement parts
In the case the appliance does not operate but is under warranty, return the product
to the place it was purchased for a replacement. Please be aware that a valid form of
proof of purchase will be required. For additional support, please contact our Consumer
Service Department at 0800 028 7154 or email:
BrevilleEurope@newellco.com.
Waste disposal
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. E-mail us at
BrevilleEurope@newellco.com for further recycling and
WEEE information.
Troubleshooting
For troubleshooting and FAQs visit www.breville.co.uk/faqs.
Problems
Possible Causes
There is no steam.
The appliance is not
plugged in, or not
switched on.
The water level is too low.
The steam pump has not
been primed.
You are using the
appliance for the first time.
6
Problems
There is no steam.
at the same time
There is noise emitting
from the appliance.
The appliance does not
heat up.
The water tank is leaking.
Steam rate decreases.
The steam leaves stains
on the fabric or the
appliance spits.
Electrical safety
Solutions
If the plug is not suitable for the socket outlets in your home, it can be removed and
Check that your appliance
replaced by a plug of the correct type. If the fuse in a moulded plug needs to be
is correctly plugged in and
changed, the fuse cover must be refitted. The appliance must not be used without the
switched on.
fuse cover fitted.
If the plug fuse requires replacement,
Unplug your appliance
a fuse of the same rating as that
and refill it.
fitted by the manufacturer must be
Refer to the 'Priming
used. In order to prevent a hazard
your handheld garment
do not fit a fuse of a lower or higher
steamer before use'
rating.
section.
If the terminals in the plug are not
Refer to the 'Priming
marked or if you are unsure about
your handheld garment
the installation of the plug please
steamer before use'
contact a qualified electrician.
section.
Possible Causes
The water tank is not fully
in place.
The appliance is in
auto-off mode.
The water level is too low
and the pump is pulling
air.
The appliance is heating
up.
The appliance is not
plugged in, or not
switched on.
The appliance is in
auto-off mode.
The water tank is not
fully in place or the fill
inlet cover is not closed
properly.
Calc build up.
You are using water with
additives.
The appliance has not
been cleaned enough
after the descaling
operation.
You are using liquids other
than water to descale the
product.
This appliance must be earthed.
Solutions
Ensure that the fill inlet
cover is closed and that
the water tank snaps
when put into place.
Refer to the 'Auto shut
off feature' section.
Unplug your appliance
and refill it.
This is normal when the
appliance is heating up.
Check that your appliance
is correctly plugged in and
switched on.
Refer to the 'Auto shut
off feature' section.
Ensure that the fill inlet
cover is closed and that
the water tank snaps
when put into place.
Refer to the 'Descaling
instructions' section.
Never add any additive in
the water tank.
Refer to the 'Descaling
instructions' section.
Use only water during
descaling operation. We
recommend using distilled
water.
7
Advertisement
