Directory 1. Important 2. Safety caution 3. Preparations before installation 4. Packing list 5. Installation steps cations 7. About the the side button 8. About the remote controller 9. How to use 10. Maintenance 11. If a long idle period is expected 12.
1. Important Please read this instruction carefully before use. - The product must be repaired by an authorized professional service personnel, otherwise the manufacturer will not be responsible for the corresponding warranty. - The power supply component is coupled with the machine. If the power supply component is damaged, in order to avoid danger, it must be replaced by an authorized professional personnel from the manufacturer, otherwise the manufacturer will not be responsible for the corresponding warranty.
2. Safety Caution - Before use, please read the following safety precautions carefully. - Improper use of the product may cause serious accidents. - The following content is closely related to safety, please be sure to strictly comply with the requirements. Warning: Refers to the contents that may cause serious personal safety or property damage.
Page 5
4. When inserting and unplugging the power plug, hold the plug body. the part of the wire. This picture is for reference only 6. The power plug should be fully inserted. (such as the following) should adjust the temperature of the seat to normal temperature. Children The elderly The patient...
Page 6
PROHIBITION 2. - - Do not replace the power plug or power cord by yourself. - If the power supply cord is damaged, to avoid danger, it must be replaced by an authorized service professional from the manufacturer. 3. Do not scratch, damage, process, forcibly bend, stretch, tighten, bind, press, or shorten the power cable.
Page 7
Do not touch with wet hands Do not remove or insert the power plug with wet hands. Otherwise it can be a cause of electrocution. Do not disassemble If the product is faulty, please immediately shut down and unplug the power plug. Bring it to the customer service center, do not dismantle or modify the product by yourself.
Page 8
without tools in case of emergency. Otherwise, the accidental failure of the product may cause personal injury or property loss. 2. Do not touch or step on the faucet. Otherwise it may cause scratches or damage to the cover. Do not place cigarettes and other combustible materials near the product.
3. Preparations before installation The side button Inlet water pipe Bidet seat Filter Upper cover Bolts Warm dry Adjustment sheet Night light Front wash plughole Rear wash plughole Remote control and holder Battery Nozzle...
Page 10
Preparations before installation 128mm 392mm Cross screwdriver Drill Electric drill Tape Suggestions for connecting power supply and water inlet. In the room where the product is installed, a water supply switch should be installed in the accessible position. This switch can be used to without tools in case of emergency.
Fixed plate Filter Electronic bidet Adjustment sheet Inlet water pipe Bolts and expanding nuts Remote control and holder Electronic Bidet AIB2211/97 User Manual Expansion screw set of Remote control battery AAA User manual leakage protection plug list Designation Quantity...
5. Installation Steps This product has been tested before delivered in the factory, there may be a small amount Bolts Adjustment sheet As shown in the picture, install the expanding completely tightened. installed on the ceramic for trial installation, adjust the position, then press the side of the product push rod to remove the product, screw the bolts down .
Page 13
5. Install the remote control. Swipe up to remove the remote control. Unit: mm 2- 4.5 A. Drill two 4.5mm diameter holes with a depth of >20mm in appropriate positions on the wall according to the position dimensions shown. C. Secure the remote control D.
Page 14
Warning through the plug. When using other electrical appliances, the product does not replace the basic safety measures of other electrical appliances. product plug. 8. Function test Test run Gently cover the sensing position on the seat with your hand, and at the same time press the rear wash/front wash button to to prevent water from splashing on yourself 9.
Designation Electronic bidet Model AIB2211/97 Rear wash Front wash Child wash Wash Moving wash 5 level setting Water pressure adjustment 5 level setting + normal temperature level Water temperature adjustment 5 level setting Nozzle position adjustment Warm dry Warm dry...
Explanation: Rated power: Under the conditions of environmental temperature 23 ±2 , static pressure of water inlet 0.2MPa ± 0.02MPa, water inlet temperature 15 ±0.5 , the function of is completed. Maximum input power: The average power of this product under the conditions of environmental temperature 23 ±2 , inlet static pressure 0.2MPa ±...
8. About the remote controller Night light button mode/ stop button Position forward button Water pressure Water pressure increase button reduction button button Rear wash/ Front wash/ Move button Move button Children's washing IonShield button button Water temperature Seat temperature button (Long press adjusting button for power saving)
9. How To Use 1. Rear wash/ Move button after rear wash for about 3 minutes or leaving the seat, or press the “ ” button to Press “ ”button again to stop the mobile wash. 2. Front wash/ Move button after front wash for about 3 minutes or leaving the seat, or press the “...
Page 19
" " can be adjusted. First gear Second gear Third gear Fourth gear Fifth gear 7. Nozzle Cleaning for cleaning for about 2 minutes, operate the nozzle again to retract and self-clean. 8. Seat temperature setting Normal First gear Second gear Third gear Fourth gear Fifth gear...
- When the IonShield is turned on, the aperture on the side button shows strong on according to the above logic until the function is completed or stopped. - After entering the IonShield sterilization function, if you press long / short to switch - During the operation of IonShield sterilization function, press "...
Page 21
to prevent water from seeping into it. Otherwise, it may lead to functional failure of the product; 3. Remove the bidet No more than 45 degrees 4. Clean the bidet and ceramics After removing the bidet body, you can clean the left and right sides and bottom of the bidet, as well as around the ceramic surface.
cycle depends on the water quality). Turn on the water element. source. 11. If a long idle period is expected When the following two situations are encountered: The room temperature is lower than 0 Please drain the water in the product pipeline according to the following steps: Step 1: Step 2: Step 3: Unplug the power cord.
13. Troubleshooting Phenomenon Cause Solution Turn on the power supply. Reset the night light assembly to "turn on" the night light. Night light function Reset the night light assembly to Night light on The night light is set to "on". The nozzle will be automatically Automatic retracting retracted 2 minutes after manual...
Page 25
The warm air Is the warm air temperature set Reset the warm air temperature temperature is not to a lower state? to a higher state. high enough The function of warm Warm air air is not working Wash function activated. function then start the warm air function.
14. List of environmental protection According to the relevant provisions and requirements of the administrative measures for the restriction of the use of hazardous substances in electrical and electronic products of the people's Republic of China, the following forms including the name of electronic products and hazardous substances are provided.
15. Product Warranty Service Guide - The product is guaranteed for two years from purchase date. If you need more information, please visit our website: www.philips.com/welcome. - Within two years from the date of purchase, you will be guaranteed free of charge for any damage caused by manufacturing process or original parts under normal use - This free service does not include consumable parts (cartridge, nozzle, ect.), auxiliary...