Easylife EL-DHM-70S Instruction Manual

Note: Read the entire instruction manual before you start installation and assembly.
The product is powered by electricity. In order to avoid burns, fire and electric shock and make sure the
safe and correct use of the system and maintain the longevity of the overall construction and the built-in
electronics, please read the instructions carefully.
• This appliance can be used by children aged from 8 years and above if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision.
•Persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge must
not use the appliance, unless they're under supervision, understand the hazards involved or they have
been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of
these persons.
• Don't leave the cords or plug unorganized in order to prevent tripping hazards.
• Any attempts to reconstruct the construction aren't allowed.
• Do not begin the installation until you have read and understood all the instructions and warnings
contained in this installation sheet. If you have any questions regarding any of the instructions or
warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual.
Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building
experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all
attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
• Please do not disassemble or change the electronic components of the product
without authorization.
Electrical Safety Instructions
• The appliance is only to be used with the power supply unit provided with the appliance. Alterations of
the given power unit aren't allowed.
• Never operate the system with a damaged power supply cord or plug. If any parts is damaged, please
contact your service agent of purchase for a replacement.
• Never operate the system if it's in moist environment or its electrical components has contact with liquids.
• Don't clean the product while the power is still connected.
• Don't disassemble or replace components while the power is still connected.
• Unplug the appliance when the system isn't in use, and place the power plug out of children reach.
6 WARNING:
Do not open the electrical cover.
G
WARNING:
Never operate the mount
without a TV installed.
Remote Control Operation Instructions
A. Button Functions
1.Upward/Downward Movement
Press the " " button, the TV mount will move upward to the lowest-profile position against the ceiling.
Press the " " button, the TV mount will move downward to the maximum tilt angle position (75° by default).
Press the " " button to stop the motion. (Tips: Clear up all obstacles within the range of motion.)
OK
2.Memory Setting
Press the " " or " " button for 1 seconds and you will hear a beep, indicating that the current position
has been saved to memory. The "
3.Recall Memory
Press the " " or " " button and the mount will automatically get to the position saved in the
corresponding button " " or "
4. Reset Mode
If the TV mount can't be adjusted to the highest position(0 degree against the ceiling) or the lowest position
(max. tilting position), unplug and re-plug the power. Then press and hold the "
Mount will retract to the highest position, that means the system has been successfully reset.
5.Reset the Tilt Range for Pitched Ceiling
RMT-02
The TV mount is 0°~75° adjustable by default. Please reset the tilt range if you use as a pitched ceiling TV mount.
romote control
Prepare: Reset the system (see Instructions on A. Button Functions - 4. Reset Mode).
Step 1: Press " ", " " and " OK
Step 2: Press and hold the "
this step 5 times. The unit will emit a long beep to indicate success.
Note: Step 1, 2 should be finished in 2 minutes, or it will fail to reset.
Note1: Long press for 5 seconds to disconnect the device from the app.
SET
Note2: The remote controller is powered by two AAA batteries (not included).
B. Manual Mode
In any position (but the minimum position against the ceiling), when manually push up the TV ceiling mount
over a distance. The TV ceiling mount will automatically return back to the minimum position against the ceiling.
WARNING
H
" " " buttons can each store a different position.
".
" button for 5 seconds.
OK
" buttons and adjust to the proper position.
" button until the unit beeps once. Repeat
Instruction Manual
MOTORIZED TV
CEILING MOUNT
EL-DHM-70S
VESA Compatible
200x100 200x200
300x200 300x300 400x200
400x300 400x400 600x400
EL-DHM-70W
C. Coding of Remote Controller and Control Box
Step 1:
When the mount is powered on, press the small button
on the control box with a thin tool as shown. The unit emits a
beep, indicating that the control box is on standby for program coding.
Step 2:
Press the " SET "button on the remote control, and the control box repeatedly beeps for approximate 10 seconds indicating
that the remote control is being programmed. The process will be finished automatically until you can't hear a beep any longer.
Note: The TV Mount can be matched with up to 20 remote controllers. To clean up the data of all the remote controllers,
press and hold the code matching button for 5 seconds then release. The unit will emits two beeps confirm the successful clean up
and vice versa.
In Front
This repair guide intents to help you identify and solve the minor problems caused by unusual operation of the electric system
of our electric TV mounts. The simple procedures in this manual are easy to follow and capable of solving the most problems
happened in everyday use.
Error Indication
1. The Buzzer Constantly Gives Out Alarm Sound:
The Error Of Positioning Signal
Reset the system by following the instruction manual. If the alarm
sound continues, please contact us to replace the product.
Remote Control Problems
1. Abnormal Loss Of Power
(Normally Batteries Are Out Of Power After 24hrs Without
Using The Remote Control.)
Please contact us to replace remote control.
2. Buttons On Remote Control Don't Work.
Please check if the batteries have power. If the problem isn't solved,
please contact us to replace the remote control. If the problem is still
not solved after the replacement, please contact us to replace the
product.
3. The Insensitivity Of Remote Control
(The Functional Distance Is Less Than 3m.)
Please replace the batteries. If the problem is still not solved,
please contact us to replace remote control.
Abnormal Operation:
The TV Mount Can't Be Adjusted To 0° Or 75°
Please reset the system by following the instruction manual.
If the problem is still not solved, please contact us to replace
the product.
Can't Operate
Please check if the power adaptor is properly connected to
the product. If so, please turn the power on. If there is no buzzer
sound or red light power indication, please check if the power
adaptor works properly. If the power adaptor doesn't work please
contact us to replace the power adaptor. If the power adaptor
works properly, but the TV mount doesn't work, please contact us
to replace the product.
Abnormal Noise
Please contact us to replace the product.
70"
200x400
MAX 35kg 35kg
(77lbs) (77lbs)
RATED RATED
FLAT/CURVED
1
24hrs
1
OR
1
1
or
1 1
2
1
2
2
2
1
2
3
2