Specifications - Panasonic EQ-500 Series Manual

SPECIFICATIONS

Type
Item Model No.
CE marking directive compliance
Adjustable range (Note 2,3) 0.2 to 2.5 m
Sensing range (at max. setting distance) (Note 3) 0.1 to 2.5 m
Hysteresis (Note 3)
Supply voltage
AC: 4 VA or less
Power / Current consumption
DC: 3 W or less
Relay contact 1a
• Switching capacity: 2 50 V AC 3 A (resistive load)
• Electrical life: 100,000 or more switching operations
Output
• Mechanical life: 50 million or more switching operations
Output operation
Short-circuit protection
Response time 20 ms or less (For EQ-50□T depends on the setting timer period) 2 ms or less (For EQ-51□T depends on the setting timer period)
Operation indicator
Stability indicator
Distance adjuster
Sensing mode
Timer function
Automatic interference prevention function
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
2,000 V AC for one min. among supply terminals, non-supply
Voltage withstandability metal parts and relay contact output terminals, 1,000 V AC for
one min. between relay contacts
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
Receiving element
Material
Connection method
Cable
Cable length
Weight
Accessory
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C
2) The adjustable range stands for the maximum sensing range which can be set with the distance adjuster. The sensor can also detect an object 0.1 m
0.328 ft, or more, away.
3) The adjustable range, sensing range and hysteresis are specified for white non-glossy paper (200 × 200 mm
4) Note that the detection may be unstable depending on the mounting conditions or the sensing object. In the state that this product is mounted, be
sure to check the operation with the actual sensing object. Refer to
USE" for details.
Adjustable Range Reflective Photoelectric Sensor
Multi-voltage
With timer
EQ-501 EQ-501T EQ-502
Low Voltage Directive, EMC Directive, RoHS Directive
0.656 to 8.202 ft 0.2 to 1.0 m
0.328 to 8.202 ft 0.1 to 1.0 m
24-240 V AC ±10 % or 12 to 240 V DC ±10 %
Ripple P-P 10 % or less
AC: 5 VA or less AC: 4 VA or less
DC: 4 W or less DC: 3 W or less
30 V DC 3 A (resistive load)
(switching frequency 1,200 operations/hour)
(switching frequency 18,000 operations/hour)
Switchable either Detection-ON or Detection-OFF
–
Green LED (lights up under stable operating condition)
–
Incorporated with
variable
– –
(0.1 to 5 sec.)
ON-delay/
OFF-delay timer
–25 to +55 °C –13 to +131 °F
Incandescent light: 3,000 ℓx or less at the light-receiving face
100 MΩ, or more, with 500 V DC megger among supply
terminals, non-supply metal parts and relay contact output
terminals as well as between relay contacts
10 to 55 Hz frequency, 1.5 mm
500 m/s acceleration (50 G approx.) in X, Y and Z directions three times each
2
Infrared LED (Peak emission wavelength: 855 nm
Enclosure: ABS, Front cover: Polycarbonate, Display cover: Polycarbonate
Suitable for round cable ø9 to ø11 mm
Total length up to 100 m
Net weight: 100 g approx.
With timer
EQ-502T EQ-511
0.656 to 3.281 ft 0.2 to 2.5 m
0.328 to 3.281 ft 0.1 to 2.5 m
10 % or less of operation distance
12 to 24 V DC ±10 % Ripple P-P 10 % or less
AC: 5 VA or less
DC: 4 W or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1 V or less (at 100 mA sink current)
PNP open-collector transistor
• Maximum source current: 100 mA
• Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 1 V or less (at 100 mA source current)
Orange LED (lights up when the output is ON)
2-turn mechanical adjuster with indicator
Incorporated with
variable
–
(0.1 to 5 sec.)
ON-delay/
OFF-delay timer
Incorporated (Note 4)
IP67 (IEC)
(No dew condensation or icing allowed), Storage: –30 to +70 °C
35 to 85 % RH, Storage: 35 to 85 % RH
1,000 V AC for one min. between all supply terminals
connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply
terminals connected together and enclosure
0.059 in double amplitude in X, Y and Z directions for two hours each
2-segment photodiode
Screw-on terminal connection
ø0.354 to ø0.433 in
328.084 ft is possible with 0.3 mm
Adjusting screwdriver: 1 pc.
"Automatic interference function
EQ-500
SERIES
DC-voltage
With timer
EQ-511T EQ-512
EMC Directive, RoHS Directive
0.656 to 8.202 ft 0.2 to 1.0 m 0.656 to 3.281 ft
0.328 to 8.202 ft 0.1 to 1.0 m 0.328 to 3.281 ft
45 mA or less
0.4 V or less (at 16 mA sink current)
0.4 V or less (at 16 mA source current)
Incorporated
Switchable either BGS or FGS function
Incorporated with Incorporated with
variable variable
–
(0.1 to 5 sec.) (0.1 to 5 sec.)
ON-delay/ ON-delay/
OFF-delay timer OFF-delay timer
–22 to +158 °F
0.034 mil, modulated)
, or more, cabtyre cable.
2
Net weight: 85 g approx.
+73.4 °F.
7.874 × 7.874 in) as the object.
(p.7)" of "PRECAUTIONS FOR PROPER
5
With timer
EQ-512T