Canon imageRUNNER 1750 Series Service Manual page 245

No. Tx/Rx
##0670 [Tx] At V.8 late start, the V.8 competency of DIS on the receiving machine side was
detected, and a CI signal was sent. However, the procedure failed to be performed,
and the circuit was released due to T1 time-out.
##0671 [Rx] After the CM signal of the calling party was detected at V.8 call reception, the
procedure failed to move to Phase 2, and the circuit was released due to T1 time-
out.
##0672 [Tx] At V.34 transmission, the procedure failed to move from Phase 2 to Phase 3 and
later, and the circuit was released due to T1 time-out.
##0673 [Rx] At V.34 reception, the procedure failed to move from Phase 2 to Phase 3 and later,
and the circuit was released due to T1 time-out.
##0674 [Tx] At V.34 transmission, the procedure failed to move from Phase 3 and 4 to the
control channel and later, and the circuit was released due to T1 time-out.
##0675 [Rx] At V.34 reception, the procedure failed to move from Phase 3 and 4 to the control
channel and later, and the circuit was released due to T1 time-out.
##0750 [Tx] After PPS-NULL was sent at ECM transmission, no meaningful signal was
received, and the retry count of the procedure signal exceeded the limit.
##0752 [Tx] After PPS-NULL was sent at ECM transmission, DCN was received.
##0753 [Tx] After PPS-NULL was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0754 [Tx] After PPS-NULL was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit.
##0755 [Tx] After PPS-MPS was sent at ECM transmission, no meaningful signal was received,
and the retry count of a procedure signal exceeded the limit.
##0757 [Tx] After PPS-MPS was sent at ECM transmission, DCN was received.
##0758 [Tx] After PPS-MPS was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0759 [Tx] After PPS-MPS was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit.
##0762 [Tx] After PPS-EOM was sent at ECM transmission, DCN was received.
##0763 [Tx] After PPS-MPS was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0764 [Tx] After PPS-EOM was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit.
##0765 [Tx] After PPS-EOP was sent at ECM transmission, no meaningful signal was received,
and the retry count of the procedure signal exceeded the limit.
##0767 [Tx] After PPS-EOP was sent at ECM transmission, DCN was received.
##0768 [Tx] After PPS-EOP was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0769 [Tx] After PPS-EOP was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit.
##0770 [Tx] After EOR-NULL was sent at ECM transmission, no meaningful signal was
received, and the retry count of the procedure signal exceeded the limit.
##0772 [Tx] After EOR-NULL was sent at ECM transmission, DCN was received.
##0773 [Tx] After EOR-NULL was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0774 [Tx] After EOR-NULL was sent at ECM transmission, ERR was received.
7
Error Code > Error Code > Error codes related to Fax > Service error codes
Description
7 Error Code > Error Code > Error codes related to Fax > Service error codes
No. Tx/Rx
##0775 [Tx] After EOR-MPS was sent at ECM transmission, no meaningful signal was received,
and the retry count of the procedure signal exceeded the limit.
##0778 [Tx] After EOR-MPS was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0779 [Tx] After EOR-MPS was sent at ECM transmission, ERR was received.
##0780 [Tx] After EOR-EOM was sent at ECM transmission, no meaningful signal was
received, and the retry count of the procedure signal exceeded the limit.
##0782 [Tx] After EOR-EOM was sent at ECM transmission, DCN was received.
##0783 [Tx] After EOR-EOM was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0784 [Tx] After EOR-EOP was sent at ECM transmission, no meaningful signal was received,
and the retry count of the procedure signal exceeded the limit.
##0787 [Tx] After EOR-EOP was sent at ECM transmission, DCN was received.
##0788 [Tx] After EOR-EOP was sent at ECM transmission, the retry count of the procedure
signal exceeded the limit, or T5 time-over (60sec) occurred.
##0789 [Tx] After EOR-EOP was sent at ECM transmission, ERR was received.
##0790 [Rx] After EOR-Q was received at ECM reception, ERR was sent.
##0791 [Tx] A signal other than a meaningful signal was received during the ECM mode
procedure.
##0792 [Rx] At ECM reception, PPS-NULL could not be detected between partial pages.
##0793 [Rx] At ECM reception, a valid frame could not be received when a high-speed signal
was received, and a timeout occurred.
##0794 [Tx] At ECM reception, PPR with all 0 was received.
##0795 [Tx/Rx] A failure occurred in the decode processing during communication.
7-11
Description
T-7-4
7-11