Table of Contents
Advertisement
66
RECORDING
System Recording
Before presetting your VTR :
•
Switch on both the television and your VTR
•
Check that the date and time are correct
•
Insert the cassette on which the programme is to be recorded (safety tab intact).
Up to six programmes can be preset.
System Recording
VIDEO
0
F. ADV
INDEX
CLR/ RST
COUNT/ TR
MENU /
REC
TIMER
TXT/ TV
PLAY
SLOW
PAUSE/STILL
OK
CURSOR
REW
F F
STOP
SP/ LP
AUDIO
DISPLAY TV/VIDEO
A.DUB
SAT.MONI.
SAT.CONT.
PROG.
EJECT
PICTURE
Note: The numbers next to each TV programme
listing are VIDEO Plus+ code numbers, which allow
you to programme your videorecorder instantly
with the remote control. Tap in the VIDEO Plus+ for
the programme you wish to record.
38
1
Press the PROG. button.
Result : The TIMER METHOD is displayed.
** TIMER METHOD **
Note : STANDARD Timer Method is used
STANDARD
for the standard Timer
VIDEOPLUS
Programming such as TIMER
PROGRAMMING Feature, refer
to page 40 for this function.
$❷!!!!!!❿
2
Press the corresponding $ or ❷button to select the VIDEOPLUS
option and press the ❿button to select this option.
Result:
A message is displayed to allow you to enter the VIDEO
Plus+ code.
Note :
If all six programmes have
been set, the message TIMER
CODE ---------
IS FULL is displayed. Refer
to page 42 if you wish to
cancel a preset recording.
CODE:0-9
3
Press the numeric buttons to enter the code opposite the programme
that you wish to record in your television magazine.
Note :
If you wish to correct the VIDEO Plus+ code that you are
entering.
Press the ➛ button until the digit to be corrected is cleared.
Enter the correct digit
4
Press the MENU or PROG. button
Note :
When using the VIDEO Plus+
PROG
function for the first time with
PR DAY
1 WE 1 12:00→12:50
stored station, the programme
-- ---- --:--→--:---- -
number flashes. This one time,
-- ---- --:--→--:---- -
you must enter the station
-- ---- --:--→--:---- -
-- ---- --:--→--:---- -
number manually by pressing
-- ---- --:--→--:---- -
the $ or ❷button. Refer to
$❷!!!➛❿
the following page if :
DELETE:CLR/RST
The programme number or times flash
You wish to modify the programme.
5
If the programme and times are correct, press the MENU button.
6
Press the two TIMER buttons to activate the timer. If you wish to turn the timer
off any reason simply press the two TIMER buttons again.
Refer to page 42 if you wish to :
Check that your VTR has been programmed correctly
Cancel a preset recording
VIDEO Plus+ is a trademark of Gemstar Development Corporation. The VIDEO Plus+
system is manufactured under licence from Gemstar Development Corporation.
66
RECORDING
continued
If you wish to correct the programme displayed or modify certain elements, such as the recording speed, you can do so before
you press MENU a second time to confirm.
Modifying
VIDEO
If you wish to...
Select an input source other
than the tuner (AV1, AV2 or AUX)
END:
MENU
VIDEOPLUS
Record a programme every day
(Monday to Sunday) at the same time
CORRECT:➛
END:
MENU
Record a programme every week
on the same day and at the same time
Extend the recording time
1/JAN WED 21:28
Select the recording speed
START→STOP
V/P
ON
SP
MENU
Select VPS/PDC
System Recording
Programming
Then...
Press the ➛ or ❿ button, until the PR selection flashes.
Press I.SELECT button one or more times to change the input
source selection.
Result :
The programme number is replaced by :
• A1, A2 or AU for a satellite tuner or external
video input (used by another VTR for example)
• S - - - for the satellite input (used by a
satellite receiver for example) see page 22
Note :
The input source must be selected before changing
any other value.
Press the ➛ or ❿ button, until the DAY selection flashes.
Press the $ or ❷ button, until the DLY (Daily) value is
displayed.
Press the ➛ or ❿ button, until the DAY selection flashes.
Press the $ or ❷ button, until the W- (Week) value is
displayed. followed by the required day.
Example :
W - SA (Weekly Saturday)
Press the ➛ or ❿ button, until the STOP selection flashes.
Press the $ or ❷ button to increase or decrease the stop
time.
Press the ➛ or ❿ button, recording speed selection flashes.
Press the $ or ❷ button until the correct indication is
displayed :
• AUTO (Auto Tape Speed Select) : see page 40
• SP (Standard Play)
• LP (Long Play)
Press the ➛ or ❿ button, until the V/P selection flashes.
Press the $ or ❷ button, until the ON or "-" indication
is displayed.
Note : Do not select VPS/PDC unless you are sure the
programme you wish to record is broadcast with
VPS/PDC ON (by selecting "ON" in the right -
hand column on the screen), then you must set up
the start time EXACTLY according to the published
TV schedule. Otherwise the timer recording won't
take place.
39
Advertisement
Table of Contents
