Operation; Installing And Removing The Battery Pack - Craftsman CMCCS320 Instruction Manual

2. Lubricate the whole saw chain evenly before each
use as shown in Figure K. Also lubricate the saw chain
whenever replacing a fully discharged battery with a fully
charged one.
Replacing the Saw Chain (Fig. F - I)

WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to
do this could result in serious personal injury.

CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is not running.

CAUTION: The chain speed of this product is 4.4 m/s.
Only use chains that are rated at greater than 4.4 m/s.
1. Place the saw on a flat, firm surface.
2. Remove sprocket cover
Guide Bar and Saw Chain section.
3. To remove the saw chain
screw 10 in the front of the housing using the flat
screwdriver end of the wrench. Turning the screw
counterclockwise allows the guide bar
and reduces the tension on the chain so that it may
be removed.
4. Wearing protective gloves, grasp the saw chain and lift
the worn saw chain out of the groove in the guide bar.
5. Ensure guide bar is installed with the bar tip guard
positioned as shown in Fig. I.
6. Place the new chain in the slot of the guide bar, making
sure the saw teeth are facing the correct direction by
matching the arrow and graphic of the saw chain on the
sprocket cover 8 shown in Fig. I.
7. Follow instructions for Installing the Guide Bar and
Saw Chain.
Replacement chain and bar are available from your
nearest authorized service center.
The CMCCS320 requires replacement 6" (152 mm) chain
CMZCSC06. Replacement 6" (152 mm) bar CMZCSB06.
Scabbard and Wrench Storage (Fig. L, M)
The scabbard 11 has two functions, to cover the guide bar
when the tool is not in use and to store the wrench
Scabbard
1. To open the scabbard , lift up on the latch
the two halves apart.
2. To close the scabbard, close the two halves and ensure
the latch is secured to the notch
Wrench
1. Open the scabbard to gain access to the wrench.
2. Remove the wrench by lifting the wrench end up and
away from the scabbard.
3. Store the wrench in the scabbard when finished. First
install flat screwdriver end of the wrench into the retaining
slot 22 and then press the wrench end down until the
retaining clips 23 firmly secure the wrench in place.
as described in Installing the
8
5 , rotate the chain tension
4 to recede
12
20 and pull
21 .
Bar Tip Guard (Fig. A)

WARNING: Never operate the pruner without the
bar tip guard properly mounted on the guide bar
to prevent rotational kickback.
The bar tip guard
the end of the guide bar
objects which may cause the bar and chain to kickback
towards the operator. In addition to reducing the chance of
kickback, the bar tip guard
chain from touching the ground.
Transporting Pruner (Fig. A)
• Always turn unit off, remove the battery and cover the
guide bar
the pruner.

OPERATION


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Proper Hand Position (Fig. N)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
6
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires the left hand on the front
handle 14 , under the front hand guard
hand on the rear handle
NOTE: DO NOT hold the saw by the front hand guard

Installing and Removing the Battery Pack

(Fig. O)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
4
the battery pack with the rails inside the tool's handle
.
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
release button
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Operating the Pruner (Fig. A)

WARNING: Read and understand all instructions.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious personal injury.
• Guard Against Kickback which can result in severe
injury or death. See Important Safety Instructions
guard Against Kickback, to avoid the risk
of kickback.
6 reduces the chance of the chain
4 from coming into contact with
6 will reduce the chance of the
4 with the scabbard 10
13 .
12 into the tool handle, align
16 and firmly pull the battery pack out of
ENgliSh
5 at
when transporting
3 , with the right
3 .
13