Product Outline ID5MGB-CL/ID5MGC-CL is a Camera Link interfaced and 5M resolution camera module. 5M pixels CMOS sensor with diagonal length 8.528mm is utilized. Entire pixels can be read out within 1/88.7s at Full Configuration output. Features Global Shutter CMOS sensor is utilized.
Specification 3.1. General Specification (1) Image Sensor Device type Diagonal length 8.528mm, Global Shutter type (GPIXEL GMAX2505) Effective pixel number 2640(H) x 2160(V) 2.5(H) x 2.5(V) μm Unit cell size Φ8.528mm Image circle 5.400 6.600 (単位:mm) (2) Video Output Frequency 71.250MHz Pixel Clock 22.2fps...
3.2. Camera Output Signal Specification Effective Video Output 2640(H) x 2160(V) Video Output Data LVAL Camera Link (LVDS) Sync Signal Output FVAL DVAL (Exposure output) FVAL 12pin Connector 6pin (LVTTL) Exposure 12pin Connector 10pin (LVTTL) CC2・CC3・CC4 Camera Link (LVDS) (No Function) Camera Control Signal Input (4)Trigger Input...
4.2. Power LED LED lights when the camera is operational. If the power is not supplied or the camera is broken, the LED will not light. ※ LED can be turned off (address 1Bh) by serial setting. 4.3. 12pin Connector HR10A-10R-12PB (HIROSE) (CN1) IO(5V LVTTL) +5.0V(VCC) Name...
Timing Chart 5.1. Horizontal Synchronous Signals Timing (2Tap Base Configuration : 22.2fps ) Image Out Camera Link Port A 2632 2634 2636 2638 ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Camera Link Port B 2633 2635 2637 2639 ・ ・ ・ ・ ・ ・ ・ LVAL Out DVAL Out 124 CLK Effective Data : 1320 CLK 1H : 1444 CLK Camera Link ...
5.5. Horizontal Synchronous Signals Timing (4Tap Medium Configuration : 44.4fps) Image Out Camera Link Port A 2632 2636 ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Camera Link Port B 2633 2637 ・ ・ ・ ・ ・ ・ ・ Camera Link Port C 2634 2638 ・ ・ ・ ・ ・ ・ ・ Camera Link Port D 2635 2639 ・ ・ ・ ・ ・ ・ ・...
5.7. Horizontal Synchronous Signals Timing (8Tap Full Configuration : 88.7fps ) Image Out Camera Link Port A 2632 ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Camera Link Port B 2633 ・ ・ ・ ・ ・ ・ ・ Camera Link Port C 2634 ・ ・ ・ ・ ・ ・ ・ Camera Link Port D 2635 ・ ・ ・ ・ ・ ・ ・ Camera Link Port E 2636 ・ ・ ・ ・ ・ ・ ・...
5.10. Fixed Trigger Shutter Mode This is the mode to start exposure with external input trigger signals, and set the exposure time with serial □ commands. Delay time (Exposure Time Delay) from detecting trigger edge in the camera to starting exposure. □...
5.11. Pulse Width Trigger Shutter Mode This is the mode to start exposure with external input trigger signals, and set the exposure time with □ pulse width of the trigger signals. □ Delay time (Exposure Time Delay) from detecting trigger edge in the camera to starting exposure, and from detecting trigger end edge to completing exposure.
Partial Scan Mode □ 1 partial area can be set by serial commands. Function Address(Hex) Data(Hex) Full frame scan mode (00h) Partial scan mode ON/OFF Partial scan mode (01h) min:0(0000h) ~ max:2159(086Fh) Partial scan mono 40-41 min:0(0000h) ~ max:2158(086Eh) Start position color Partial scan mono...
Page 17
□ Total number of frames = Number of V blanking lines (fixed to 64H) + Number of partially valid lines (Partial scan start position + number of partial valid lines) <= 2160 must be satisfied. Partial scan start position and number of partial effective lines □...
Page 18
Horizontal cutout function It is possible to cut out the left and right in the horizontal direction with 24 pixels x n. The frame rate does not change even if you cut out the horizontal direction. Function Address(Hex) Data(Hex) min:0(00h) ~ max:54(36h) L/R Cut size(pixel) = setting value x 24pixel Horizontal cut-out min:0= Full...
Remote Communication Via camera link cable, the camera can be controlled. Communication Settings :115200bps (fixed) Baud Rate Data :8bit Stop bit :1bit Parity :None :No Control XON / XOFF ・ Send Command Format (Host to Camera) If send a command, set the command and parameter between STX and ETX. command parameter (ASCII code) (02H)
8.1. Command Specifications 1) Set some values of resister 【Command】 Set : Resister ・・・ Data (Variable-length:max 16 address) Address 【Return Value】 Succeed ・・・ Fail ・・・ 2) Get some value of resister 【Command】 Get : Resister Address Number of data acquisition (optional) 【Return value】...
Page 21
3) Set User’s data 【Command】 Set : User’s data ・・・ Table No. User’s data (fixed length :16byte) (0~3) 【Return Value】 Succeed ・・・ Fail ・・・ 【Remarks】 The commands, sets free data on the specified register, and can use 4 tables (1 table : 16 characters). 4) Get User’s data 【Command】...
Page 22
5) Save all configurations 【Command】 Configuration : Save 【Return Value】 Succeed ・・・ Fail ・・・ 6) Restore all configurations 【Command】 Configuration : Restore 【Return Value】 Succeed ・・・ Fail ・・・ 7) Get a model name 【Command】 Query : Model name 【Return Value】 Succeed ・・・...
Page 23
9) Get a firmware version 【Command】 Query : Version 【Return Value】 Succeed ・・・ ・・・ Version information (fixed length:8byte) Fail ・・・ 10) Get a detail of error information 【Command】 Query : Error 【Return Value】 Succeed ・・・ Kind Detal Fail ・・・ Kind Detail 0:...
8.2. Control Example 1) How to check trigger shutter mode. ( The command gets a value from address 04) 【Send Command】 Address 04 【Return value form camera】 Data 01 【Receive Return Value】 The camera is working with a trigger shutter mode, because the command received a 01 from the camera. 2) How to check trigger shutter mode.
Page 25
How to set partial scan mode. (The command sets 01 for address 08) 【Send Command】 Address 08 Data 01 【Return value form camera】 【Receive Return Value】 The command finished normally, because the command received ACK from the camera. How to set 01FF for manual shutter. (The command set 01FF for address 24) 【Send Command】...
Page 26
How to save configurations of a camera. (The command send CS) 【Send Command】 【Return value form camera】 【Receive Return Value】 The command finished normally, because the command received ACK from the camera. How to restore the camera to initial settings. (The command send CR) 【Send Command】...
Page 27
How to get detail of a communication error. 【Send Command】 Set the address invalid value 【Return value form camera】 【Receive return value】 The command finished abnormally, because the command received ‘NAK’ from the camera. When the command did not finish normally, retry to send command or send to get detail of a detail error command. 【Send Command】...
On very rare occasions, however, CMOS pixel defects might be noted with time of usage of the products. Cause of the CMOS pixel defects is the characteristic phenomenon of CMOS itself and IDULE is exempted from taking any responsibilities for them. Should you have any questions on CMOS pixel defects compensation, please contact us.