Advertisement
Quick Links
uincy
ab
SPECIFICATIONS
Interior Dimensions
Exterior Dimensions
Weight (lbs)
Cubic Foot Capacity
Standard Electrical
Temperature Range
Common Unit Specifications
Operating Environment: Indoor use, altitude to 6,500 ft. (2,000m) Installation Category II,
Storage Temperature:
Approvals:
Compliance:
Common Unit Construction
Exterior: Powder-Coated Steel
Insulation: Fiberglass
Thermo-control: PID Microprocessor
Issue Rev A 0122
Copyright Quincy Lab Inc. 2022
Quincy Lab, Inc.
Model 12-140E
MODEL
10-140E
12x10x10
INCHES W x H x D
31x25x25
(CM) W x H x D
13x15x11
INCHES W x H x D
33x38x28
(CM) W x H x D
19 lbs
115 / 120*
VOLTS / WATTS
Pollution Degree 2, ambient temperature 10
80% RH maximum.
o
-10
C/14
Underwriter's Laboratory Listed, Laboratory Equipment, C/UL
United States/Canadian. E212550 (115VAC models only)
UL Standard 61010-1, IEC 61010-1, 2nd Edition.
109. Shore Dr.
General Purpose Incubators
OPERATING MANUAL
MODEL
12-140E
18x16x12
46x41x30
19x21x13
48x53x33
33 lbs
115 / 235*
o
o
o
F to 70
C/158
F, 70% RH maximum.
Interior: Aluminum
Door: 140E: Acrylic, 180E: Steel Insulated
Heater: Resistive-Tubular Incoloy
Burr Ridge, Illinois 60527
Model Series 140E & 180E
Model 10-180E
MODEL
MODEL
10-180E
12-180E
12x10x10
18x16x12
31x25x25
46x41x30
13x15x11
19x21x11
33x38x28
48x53x33
19 lbs
33 lbs
115 / 270*
115 / 385*
o
o
o
C/50
F to 35
C/95
1-800-482-HEAT (4328)
o
F,
PAGE 1
Advertisement
Related Manuals for Quincy lab 140E Series
Summary of Contents for Quincy lab 140E Series
- Page 1 Exterior: Powder-Coated Steel Interior: Aluminum Insulation: Fiberglass Door: 140E: Acrylic, 180E: Steel Insulated Thermo-control: PID Microprocessor Heater: Resistive-Tubular Incoloy Issue Rev A 0122 Copyright Quincy Lab Inc. 2022 Quincy Lab, Inc. 109. Shore Dr. Burr Ridge, Illinois 60527 1-800-482-HEAT (4328) PAGE 1...
-
Page 2: Safety Precautions
Safety Precautions Safety Precautions Read Operating Instructions Thoroughly Prior to Operation Read Opera�ng Instruc�ons thoroughly prior to opera�on and observe the following safety precau�ons: • Use only a grounded outlet that is rated for your model's electrical requirement. • Do not modify the oven or factory control se�ngs to operate the oven above the stated maximum opera�ng temperature. •... - Page 3 Menu Level Functions Guide To navigate the controller's menu, please refer to the easy-to-use Menu Guide below: Menu setting changes can be done quickly with our 5-button digital microprocessor. Your incubator's controller allows you to easily do the following: Auto-tune your Incubator for maximum efficiency Set the operating set-point temperature Lock the set-temperature Select between degrees Fahrenheit or Centigrade...
- Page 4 Auto-tune The control's P.I.D values have been derived from a performed tuning at the factory using the AT-1 option which allows for optimal performance and faster response time. You may, however, choose to tune your incubator to your specific application and/or most used set-point temperature by selecting and performing one of the tuning options shown below.
- Page 5 Chamber Loading Understanding the unit's light pressure thermal convec�on and "load-effect" are necessary to op�mize unit performance. Ar�cle or media processing �mes and/or uniformity are largely dependent on load density and posi�oning. Important guidelines to chamber loading and processing: Load the incubator so that air circula�on within the chamber is not impaired. Leave a space between ar�cles on the shelf.
-
Page 6: Maintenance
For a complete list of replacement components, part and additional equipment, visit us on the web at www.quincylab.com Technical Support If you have any ques�ons or need technical assistance, contact Quincy Lab technical support for further assistance, or visit us www.quincylab.com on the web at Email: information@quincylab.com...