Simulation - Sharp AR-FX7 Service Manual

[6] SIMULATION

1. Code-type simulation
A. Operating procedures and operations
* Entering the simulation mode
→
1) #/P key (program) ON Asterisk (*) key ON
→
Asterisk (*) key ON Ready for input of a main code of simulation
2) Entering a main code with the 10-key
3) Entering a sub code with the 10-key
4) Select an item with the scroll key and the item key.
5) The machine enters the mode corresponding to the selected item.
Press START key to start the simulation operation.
To cancel the current simulation mode or to change the main code
and the sub code, press the CUSTOM SETTINGS key.
* Canceling the simulation mode to return to the normal mode
1) Press CLEAR ALL key.
2. Simulation code list
Code
Main Sub
22 5 Used to check the ROM version of each unit
(section).
11 Used to display the FAX send/receive counter
(FAX reception and print counter).
24 10 FAX counter data clear
46 12 FAX exposure level adjustment (1 mode automatic
adjustment)
13 FAX exposure level adjustment (Normal mode
individual adjustment)
14 FAX exposure level adjustment (Fine text mode
individual adjustment)
15 FAX exposure level adjustment (Super Fine mode
individual adjustment)
16 FAX exposure level adjustment (Ultra Fine mode
individual adjustment)
48 8 FAX magnification adjustment (read)
9 FAX magnification adjustment (print)
50 8 FAX lead edge adjustment (read)
9 FAX lead edge adjustment (print)
66 1 Used to change and check the FAX-related soft
SW.
2 Used to clear the FAX-related soft SW. (Except for
the FAX adjustment values)
3 FAX PWB memory check
4 Signal send mode (Signal send level: Max.)
5 Signal send mode (Signal send level soft SW
setting)
6 Printing the confidential password
7 Print the screen memory contents
8 Voice Message send (Signal send level: Max.)
(print) (Japan only)
9 Used to send the voice message. (Signal send
level: Set by soft SW.)
10 Image data memory clear
11 Used to send 300bps signals. (Signal send level:
Max.)
12 Used to send 300bps signals. (Signal send level:
Set by soft SW)
13 Used to register the dial numbers.
14 Used to perform the dial test. (10 PPS send test)
15 Used to perform the dial test. (20 PPS send test)
16 Used to perform the dial test. (DTMF signal send
test)
→ →
CLEAR key ON
→
START key ON
→
START key ON
Function
AR-FX7 SIMULATION 6 - 1
Code
Main Sub
66 17 Used to check the DTMF signal send operation.
(Signal send level: Max.)
18 Used to check the DTMF signal send operation.
(Signal send level: Set by soft SW.)
19 Used to write the SRAM data to the Flash ROM.
20 Used to write the Flash ROM data to the SRAM.
21 FAX information print
22 Handset sound volume adjustment (Japan only)
24 Used to clear the FAST storage data. (SEC only)
30 Used to set the TEL/LIU.
31 Used to set the TEL/LIU.
32 Receive data check
33 Signal detection check
34 Communication time measurement display
37 Speaker sound volume adjustment
41 CI signal check
52 Ringer check
3. Details
22
22-5
Purpose Adjustment/Setting/Check
Function Used to check the ROM version of each unit (section).
(Purpose)
Item Software
Operation/procedure
Used to display the ROM version of each section.
[Display example]
→
ROM version 1.250 [1.25] (up to 2 decimal places)
The display of the protocol monitor and the soft SW follows this dis-
play.
S/N Machine serial number
MCU Main Control Unit
IMC IMC
OPE Panel + Panel label code
PRINTER PRINTER
NIC NIC (For the Soft Nic, the Soft Nic version is displayed.
When the AR-NC5 is installed, the AR-NC5J version is
displayed.)
FINISHER FINISHER
FAX FAX
If it is not installed, "- - - - - - - - - -" is displayed.
[Label code display]
Contents of "XXX" section on the display below
Panel
Destination Selection code
display
JPN Japan
EFS SEC AJ/AM
SECL AL/AC
SUK BK/BB
EEU SEEG/ GG/GD
SEA/East
Europe,
etc.
Function
Panel software support
language
Japanese, American
English, English
American English, English,
French, Spanish
English, German, Polish,
Czech, Hungarian, Greek,
Turkish, Russian, French,
Italian, Slovak