Related Manuals for GE Monogram ZIRS360NNLH
Summary of Contents for GE Monogram ZIRS360NNLH
- Page 1 Installation Instructions 36” Built-In All-Refrigerators and All-Freezers 31-49062-1 224D2601P002 10-14 GE monogram.com...
-
Page 2: Safety
• – Be sure to leave these instructions failure due to improper installation is not covered under the with the Consumer. GE Appliance Warranty. Note to Consumer • – Keep these instructions with See the Owner’s Manual for warranty information. - Page 3 CONSIGNES DE SÉCURITÉ Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », «...
-
Page 4: Table Of Contents
Contents Safety 2, 3 Step 3. Install Side Panels Step 4. Install Case Trim Planning Guide Step 5. Anti-Tip Procedures 18-19 The Installation Space Step 6. Level Unit Dimensions and Clearances Step 7. Secure Unit to Cabinetry Customization Basics Step 8, Secure Unit to Wall 3/4”... -
Page 5: The Installation Space
For a 90° door swing, allow 4” minimum clearance to floor or back wall. The water line should be 1/4” O.D. a wall for framed and stainless steel models. Allow 5” copper tubing or GE QuickConnect ™ kit between the minimum clearance for professional models. - Page 6 Design Guide CLEARANCES FOR FLUSH INSTALLATION ONLY 4" 15" Clearances for two products installed side-by-side These units are equipped with a 3-position door stop. with the same (left or right) door swing The factory set 115° door swing can be adjusted to 90° Allow 2”...
- Page 7 Design Guide CLEARANCES FOR STANDARD INSTALLATION AND STAINLESS MODELS ONLY 25" 2" Min. to 15" 130° Door Wall Swing 130° Clearances for two products installed side-by-side These units are equipped with a 3-position door stop. with the same (left or right) door swing The factory set 115°...
-
Page 8: Customization Basics
Design Guide CUSTOMIZATION BASICS: Optional Accessory Kits • ZKHSS2: Monogram Tubular Stainless Steel handles Framed Or Overlay Panels, Custom designed to fit 3/4” overlay panels. Handles and Accessory Kits • ZKHPSS1: Pro Tubular Stainless Steel handle designed to fit 3/4” overlay panels. Professional Style Stainless Steel Models •... -
Page 9: 3/4" Overlay Panel Dimensions - Flush
Design Guide CUSTOM HANDLE DESIGN GUIDE 3/4” OVERLAY PANEL DIMENSIONS (Flush Installation Only) (Flush Installation Only) For custom handle installation, counterbore holes in For a more custom appearance, overlay panels may be rear of decorative panels may not exceed 1/4” depth installed to give a flush appearance with surrounding to ensure 1/2”... -
Page 10: 1/4" Framed Panel Dimensions - Standard
Design Guide 1/4” FRAMED PANEL DIMENSIONS (Standard Installation Only) 5/16" If you choose to install framed panels, they must be cut to Trim Door Reveal the dimensions shown. The panels will slide into the frame on the door and grille. If the custom panel is less than 1/4”... -
Page 11: Side Panels
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the unit The ZUG2 unified grille panel kit provides for the will be exposed. The 1/4” side panels will slip into the installation of a framed or overlay grille panel. side case trim. -
Page 12: 130° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. Top View 130° DOOR SWING (Standard Installation Only) Scale 1:1... -
Page 13: 90° Door Swing
Design Guide Frameless Cabinets: Refrigerator The case trim overlaps or Freezer Case Trim cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow 23-7/8" for filler strips. From Rear of Unit Cabinet Front... -
Page 14: Installation Instructions
• 7/16” and 1-1/4” open-end wrench replaced with a properly grounded 3-prong wall outlet. • 1/4” copper water line tubing or GE SmartConnect ™ DO NOT, UNDER ANY Refrigerator Tubing kits CIRCUMSTANCES, CUT OR REMOVE •... -
Page 15: Parts Identification
Installation Instruction PARTS IDENTIFICATION: Panel Bracket, Top Right Trim, Handle Side Visor Panel Bracket, Bottom Left Panel Bracket, Bottom Right Trim, Handle Side Cover Panel Bracket, Top Left Panel Bracket, Top Trim, Freezer Hinge Side Panel Bracket, Bottom Door Bracket (4); Installed on door Door Panel Template TOP IF HINGES ARE ON THE LEFT... -
Page 16: Step 1 Remove Packaging
Turn on the nearest faucet long enough to clear the line leading into the water line connection. of water. NOTE: The only GE approved plastic tubing is supplied in • Install a shut-off valve between the icemaker water the GE SmartConnect Refrigerator Tubing kits. -
Page 17: Step 4 Install Case Trim
Installation Instructions STEP 4 INSTALL CASE TRIM STEP 5 INSTALL ANTI-TIP BRACKET (cont.) Install case trim using supplied right hand and left hand case trim pieces and case trim screws. Attach case trim Standard/Stainless Installation Only to each side of case as shown in illustration using case •... -
Page 18: Step 5. Anti-Tip Procedures
Installation Instructions STEP 5 INSTALL ANTI-TIP BRACKET • Gently pull back at the ends of the plastic straps to make (Standard/Stainless Installation the channel rest flush behind the wall. only) (cont.) • Hold the ends of the straps in one hand and slide the plas- tic cap along the straps until the flange of the cap is flush Wall Bracket with the wall. - Page 19 Installation Instructions STEP 5 INSTALL ANTI-TIP BRACKET Power Cord Locate the power cord inside the left cavity. If it has not (Standard/Stainless been adjusted so the plug is easily accessible, Installation only) (cont.) do so now. Remove Grilles for Access to Anti-Tip Locking Hooks Fresh Food Unit •...
-
Page 20: Step 6 Level Unit
Installation Instructions STEP 6 LEVEL UNIT STEP 7 SECURE APPLIANCE TO CABINETRY All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable Flush Installation Only wheels. Both are accessible from the front of the unit. Whenever possible, perform this step for anti-tip security, •... -
Page 21: Step 8 Secure Unit To Wall
Installation Instructions STEP 8 SECURE UNIT TO WALL Standard and Stainless Installation Only • The “L” rods can be found in the upper left and right corners of the unit in the access compartment. Look through the access compartment to make sure the rods line up with the anti-tip bracket. -
Page 22: Step 9 Adjust Door Swing
Installation Instructions STEP 10 REMOVE DOOR TRIM - FLUSH STEP 9 ADJUST DOOR SWING INSTALLATION ONLY NOTE: This appliance has a 3-position door stop. When space does not allow the door to swing open fully to Use the supplied Torx wrench or T10 Torx head driver to remove all exposed trim screws securing aluminum 115°, you may change the door swing to a 90°... -
Page 23: Step 11. Layout Decorative Door Panels
Installation Instructions STEP 11 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY Decorative wood panels must be cut to a thickness of 6. Using a pencil, trace the outline of the notch out of the 3/4”. The dimensions of each panel can be determined template at the top corner of the door. -
Page 24: Step 12. Attach Brackets To Panels
Installation Instructions STEP 12 ATTACH BRACKETS TO PANELS - FLUSH INSTALLATION ONLY Locate wood panel brackets and wood panel screws in 3. Align the four tapered holes in one of the top panel Flush Inset Hardware Kit located inside the appliance brackets with the four holes in the top of the door drawer. -
Page 25: Step 13. Hang Decorative Door Panels
Installation Instructions STEP 13 HANG DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY Panel with attached brackets will mate with steel brackets already attached to top, sides, and bottom of the door. Each bracket attached to the door will have two machined screws recessed inside the door to provide anchoring points for wood panel brackets to install onto the doors. -
Page 26: Step 14. Layout Decorative Grille Panel
Installation Instructions STEP 14 LAYOUT DECORATIVE GRILLE STEP 15 INSTALL GRILLE PANEL - FLUSH PANEL - FLUSH INSTALLATION INSTALLATION ONLY ONLY 1. Pull grille panel bracket in an outward motion allowing Grille area will also have decorative wood panel it to swing out and up to the fully open position. attached to installed steel bracket. -
Page 27: Step 16. Adjust Decorative Panels
Installation Instructions STEP 16 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION ONLY The panel can be adjusted approximately 1/8” both left 3. Check that the door panel is in plane with the face of and right, up and down, as well as outward from the the cabinets. -
Page 28: Step 17 Replace Trim
Installation Instructions STEP 16 ADJUST DECORATIVE PANELS STEP 17 REPLACE TRIM - FLUSH - FLUSH INSTALLATION ONLY INSTALLATION ONLY (Cont) 1. Replace trim and 6 screws on hinge side of the door. 2. Replace handle visor trim and four screws on the han- 5. -
Page 29: Step 18 Connect Water Supply
™ NOTE: The only GE-approved plastic tubing is supplied STEP 20 INSTALL TOEKICK in the GE SmartConnect ™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the • Locate the supplied toekick (shipped taped to line is under pressure at all times. - Page 30 Notes...
- Page 31 Notes...
- Page 32 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. 31-49062-1 Appliances 224D2601P002 Appliance Park Louisville, KY 40225 10-14 GE GEAppliances.com Printed in the United States...