Table of Contents
Advertisement
You can set the unit to record up
to 8 programmes, up to a month
in advance. Daily or weekly
programme recordings are also
available.
• Be sure to set the clock before
entering a timer programming.
Insert a recordable disc or a
tape with a record tab.
1
In stop mode, press
[TIMER PROG.].
Timer Programming list will appear.
Timer Programming
Date
Start
End
1. - - -
2. - - -
2
Select a programme that is not
set using [Cursor K / L], then
press [ENTER].
3
Enter the date using [Cursor
K / L], then press [Cursor B].
Timer Programming
Date
Start
End
1. 01/01
--:--
--:--
2. - - -
Each time you press [Cursor L]
at the current date, the timer
recording date will change as
follows.
e.g., 1st January
01/01
Daily
M-F (Mon.-Fri.)
W-SAT
W-FRI
W-SUN
31/01
32
EN
Downloaded from:
http://www.usersmanualguide.com/
Timer Recording
4
Enter the time to start and to
end using [Cursor K / L], then
press [Cursor B].
1. 01/01
2. - - -
5
Select the channel number to
record using [Cursor K / L],
then press [Cursor B].
1. 01/01
2. - - -
To record from the external input,
select "AV1", "AV2", or "AV3".
VCR
DVD
DVD
CH
Mode
6
VCR
Select the recording media
("DVD" or "VCR") using [Cursor
K / L], then press [Cursor B].
1. 01/01
2. - - -
7
Select the recording mode using
[Cursor K / L]. (See page 24.)
VCR
DVD
DVD
CH
Mode
VCR
P01
1. 01/01
2. - - -
Note
• If you have not set the clock, the clock setting window will appear
instead of the Timer Programming list. Continue from step 4 in "Clock
Setting" on page 22 before programming the timer.
• Press [Cursor { / B] to move the cursor in the Timer Programming list.
• If a basic recording or One-touch Timer Recording is in progress on
one component (e.g. VCR) and the timer recording set for the other
component (e.g. DVD) is about to begin, the unit automatically
switches to the programmed channel for timer recording 2 minutes
before the programmed starting time, and the recording in progress
(for VCR) will be cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the timer recording
will start without cancelling the recording currently in progress. In this
case, the recording of the same channel will be made on both DVD
and VCR.
• Cancel the timer-standby mode by pressing [T-SET] before operation
for either DVD or VCR. When finished operating, press [T-SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the power and use the
component (VCR or DVD) which is not currently timer-programmed.
Recording
Timer Programming
VCR
DVD
DVD
Date
Start
End
CH
Mode
VCR
12:00
--:--
P01
Timer Programming
VCR
DVD
DVD
Date
Start
End
CH
Mode
VCR
12:00
13:00
P01
Timer Programming
VCR
DVD
DVD
Date
Start
End
CH
Mode
VCR
12:00
13:00
P01
DVD
Timer Programming
VCR
DVD
DVD
Date
Start
End
CH
Mode
VCR
12:00
13:00
P01
DVD
XP
8
Press [ENTER] when all informa-
tion required is entered.
Your programme setting is
stored.
• To set another programme,
repeat steps 2 to 8.
• To exit, press [TIMER PROG.].
• If the recording times of two
or more programmes overlap,
"Overlap" and overlapped
programme numbers are
displayed. (See pages 33-34.)
9
Press [T-SET].
The
icon will appear on the
front panel display and the unit
enters to the timer-standby
mode.
OPERATE
OPEN/CLOSE
DUBBING
SETUP
EJECT
9
T-SET
TIMER PROG.
REC MODE
RAPID PLAY
VCR
DVD
ZOOM
CM SKIP
TOP MENU
MENU LIST
ENTER
RETURN
.@/:
ABC
DEF
1
2
3
PROG.
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
SKIP
CLEAR/C-RESET
SPACE
DISPLAY
0
REV
FWD
PLAY
VCR
DVD
REC/OTR
REC/OTR
STOP
1
8
2
3
4
5
6
7
8
Advertisement
Table of Contents
