Related Manuals for Sanyo VCC-9624
Summary of Contents for Sanyo VCC-9624
- Page 1 INSTRUCTION MANUAL VCC-9624 COLOR CCD CAMERA About this manual Before installing and using the camera, please read this manual • carefully. Be sure to keep it handy for later reference.
- Page 2 OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013.
- Page 3 This installation should be made by a qualified service person and interference received, including interference that may cause should conform to all local codes. undesired operation. Changes or modifications not expressly approved by Sanyo may void the user’s authority to operate this camera. English...
-
Page 4: Table Of Contents
CONTENTS FEATURES • Built-in interline transfer method 1/3" CCD, approx. 410,000 PRECAUTIONS ......... . . 3 picture elements PARTS NAMES AND FUNCTIONS . -
Page 5: Precautions
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. -
Page 6: Parts Names And Functions
PARTS NAMES AND FUNCTIONS Manual pan, tilt and rotation The angle of the lens can be adjusted manually in ranges indicated below. A: Horizontally ± 45˚ B: Vertically ± 60˚ C: Rotation of the camera unit ± 35˚ K M N English... - Page 7 With this camera use only the 24 V AC 2 Screw openings for base installation power adaptor model No. VPT-115 available from Sanyo. These openings are to attach the base to the ceiling or a wall using the four supplied tapping screws.
- Page 8 PARTS NAMES AND FUNCTIONS 8 Secondary lens cover L BLC (backlight compensation) switch 9 Lens 0: Backlight compensation off 1: Backlight compensation on F Focus ring For backlight compensation, set the BLC switch to 1, then, if To set the focus, loosen the focus ring knob, then turn the ring ∞...
-
Page 9: Preparations And Connections
PREPARATIONS AND CONNECTIONS Concerning the coaxial cable To connect the camera to peripheral devices, use a coaxial cable with BNC plug. • Cable type RG-6U (5C-2V), 500 m maximum. • Cable type RG-11U (7C-2V), 600 m maximum. If the type of peripheral devices connected, the type of cable used and/or the cable length are not as specified, the image and synchronization signals may not be transmitted correctly. -
Page 10: Connections And Installation
CONNECTIONS AND INSTALLATION Basic connections for monitoring or recording (Example of connection to a monitor) The peripheral devices (VCR, monitor, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. - Page 11 CONNECTIONS AND INSTALLATION Coaxial cable connection 27mm 10mm Cut and prepare the extremity of the coaxial cable (sold separately), as illustrated. Attach the coaxial cable to the base. (Cut the shielding mesh here) Loosen the CAMERA (VIDEO) OUT terminal screw (A) and the GND terminal screw (B), then insert the center wire of the coaxial cable in the CAMERA (VIDEO) OUT terminal and make sure the shielding mesh part of the cable is located under the GND terminal plate, then tighten both screws (A and B) to attach the cable.
- Page 12 CONNECTIONS AND INSTALLATION Install the camera unit onto the base. Connect the video signal cable plug (B) and the power supply cable plug (C) from the base to their respective connectors on the camera unit. Then install the camera unit onto the base.
-
Page 13: Settings And Adjustments
SETTINGS AND ADJUSTMENTS The digital process may disturb the image for about 5 seconds after the camera is turned on. C D E F Factory settings The camera is shipped from the factory with the following settings. These settings should give adequate results under normal conditions. - Page 14 SETTINGS AND ADJUSTMENTS In this case, the backlight compensation default setting may not give good results. To obtain a better image, set the BLC switch to 1 (ON), then turn the LEVEL volume control to the right until the desired correction level is obtained. Manual white balance adjustment To set the colors, first set the WB switch to M, then adjust as desired, using the (B and R) color adjustment volume controls.
- Page 15 SETTINGS AND ADJUSTMENTS Line phase adjustment When using a camera switcher to connect two cameras or more to one monitor, there may be a vertical roll of the images when switched, if the phases differ. In such a case, adjust as described below.
- Page 16 SETTINGS AND ADJUSTMENTS Zoom and focus adjustments After the camera has been installed, the zoom and focus must be adjusted while viewing on a monitor the transmitted image. Remove the lens cover, then press on both sides of the secondary lens cover to remove it.
-
Page 17: Troubleshooting
This camera is a precision instruments and, if treated with care, it will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Center. -
Page 18: Specifications
SPECIFICATIONS F2.0 ∼ 2.7, f=2.6 ∼ 5.6 mm, TV system Based on the NTSC color system Lens varifocal lens, manual zoom and Scanning system 525 TV lines, 60 field/sec., focus adjustment 2:1 interlace Iris system Mechanical auto iris Image device Interline transfer method, 1/3 inch Horizontally (pan): ±45˚, solid state CCD... - Page 19 SPECIFICATION DIMENSIONS 112mm 83.5mm 11mm 4.3mm English...
- Page 20 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual...