Related Manuals for Samsung SSA-R2000
Summary of Contents for Samsung SSA-R2000
- Page 1 SSA-R2000 RFID Reader user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.com...
- Page 2 If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) . When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.
- Page 3 Avoid aiming the controller directly towards extremely bright objects such as sun. Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus. The Mains plug is used as a disconnect device and shall stay readily operable at any time. FCC Statement Caution : Any changes or modifi...
-
Page 4: Table Of Contents
contents Features PRODUCT INTRODUCTION What’s included At a Glance Cable Color Scheme Cable Selection INSTALLATION AND EXTERNAL Installation Precautions on installation CONNECTION External Connection INITIALIZATION Output Format Basic Operations WIEGAND Output OUTPUT FORMAT RS-232 Output 4/8 BIT BURST Output Format TROUBLE SHOOTING Trouble Shooting PRODUCT SPECIFICATION... -
Page 5: Features
product introduction FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10 cm (4”) read range. It is also supported by backlighting on the keypad, enabling stable operation at night. This product permits user access through authentication of the presented proximity card and personal identifi... -
Page 6: At A Glance
product introduction AT A GLANCE Front/Rear Displays the status of the system operation. Keypad Used to enter the ID/password. 2-PIN Connector Can be connected to the power cable. 6-PIN Connector Can be connected to Wiegand, RS-232 communication cables. 8-PIN Connector Connected to the tamper, LED and buzzer control connection cables. -
Page 7: Cable Color Scheme
CABLE COLOR SCHEME ❖ 2-PIN Connector I/O Pins Signal Cable Color Power (+12V) DC +12V Earth-grounding GND (-) Black ❖ 6-PIN Connector I/O Pins Signal Cable Color Wiegand Data Output 0 WIK_DATA0 Green Wiegand Data Output 1 WIK_DATA1 White Not Used Not Used Orange RS-232 TX... -
Page 8: Installation
installation and external connection INSTALLATION Attach the provided wall mount to the wall and drill two 6-32 holes and one 1/2 inch hole on it. (See [Figure 1]) Refer to [Figure 2] below on how to secure the wall mount to the wall using the provided screws. Apply each of 5 O-rings to the corresponding point as shown in [Figure 2]. -
Page 9: Precautions On Installation
PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. -
Page 10: External Connection
EXTERNAL CONNECTION WIRING DIAGRAM SSA-R2000 Wiegand Data 0 Out Green Wiegand Data 1 Out White Tamper Switch Out(NC) Green with white stripes RS-232(TX) Tamper Switch Out(COM) Gray Purple CONTROLLER Buzzer Control In Blue RS-232(GND) LED Control In(Red) - Page 11 initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 26bit Wiegand. Adjust the format according to the controller receiving the keypad input. To change the output format, use the switch on the rear of the product.
- Page 12 initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller.
-
Page 13: Output Format
output format WIEGAND OUTPUT Timing Diagram 100us DATA-0 DATA-1 n *n : 34 or26 LOGIC Data Type (26-bit) • Bit 1 : Even Parity (bit 2 ~ bit 13) • Bit 2 ~ 9 : Facility Code (000 ~ 255) •... -
Page 14: Rs-232 Output
output format RS-232 OUTPUT Output Waveform +15V Space(=0) Indeterminate Region Mark(=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type START (0X02H) DATA (8 Char) END (0x03H) START(0X02H) DATA (1~8 Char) END (0x03H) ... - Page 15 4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0000 0110 0001 0111 0010 1000 0011 1001 0100 1010 0101 1011 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 11110000 10010110 11100001 10000111 11010010 01111000...
-
Page 16: Troubleshooting
Check the rated voltage specifi ed in the user manual and the catalog. Ensure that the card must comply with the PSK (125KHz) format provided by Samsung. - Cards of 13.56MHz format can not be used. (Contact the card retailer regarding the card format.) If the problem persists, contact the nearest customer service for your assistance. -
Page 17: Product Specifi Cation
PRODUCT SPECIFICATIONS Item SSA-R2000 Power / Current DC 12V / Max.95mA Reading Time (Card) 30ms Input Port 2 ea : External LED Control, External Buzzer Control Output Port 26bit Wiegand, 4/8bit Burst for PIN (Selectable) LED Indicator... - Page 18 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.