Sealey PTB141507 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this rollcab
‰
and topchest.
Locate the rollcab and topchest in a suitable work area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
WARNING! Use the rollcab and topchest on level and solid ground, preferably concrete.
‰
Keep rollcab and topchest clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use this rollcab and topchest for any purpose other than that for which it is designed.
8
DO NOT place the rollcab and topchest in a damp or wet location or an area where there is condensation.
8
DO NOT clean the rollcab and topchest with any solvents which may damage the surfaces or the protective coating.
8
DO NOT move the rollcab and topchest with the drawers out. To avoid tipping, open one drawer at a time and close and secure all
8
drawers whilst moving.
DO NOT step on the drawers.
8
2. INTRODUCTION
PTB141507: Heavy-duty welded steel construction for strength and durability. Textured powder coat finish. Ball bearing drawer slides provide
superior performance and carry heavier loads, double sets on large drawers. All drawers have full width sand blasted aluminium 'Lift & Latch' drawer
pulls, making easy-access while preventing inadvertent opening when box is being moved. Heavy-duty exterior handles. Supplied with non-slip
drawer liners supplied for all drawers. Gas struts fitted to lid makes opening easy. Integral locking system locks all drawers with the turn of a key.
Supplied with two keys. Use with Model No. PTB143011 Rollcab or can be a standalone unit.
PTB143011: Heavy-duty welded steel construction for strength and durability. Textured powder coat finish. Ball bearing drawer slides provide
superior performance and carry heavier loads, double sets on large drawers. All drawers have full width sand blasted aluminium 'Lift & Latch' drawer
pulls, making easy-access while preventing inadvertent opening when box is being moved. Tubular chrome plated exterior side handle. Non-slip
drawer liners supplied for all drawers. Heavy-duty Ø125mm Mag style castors, four swivel with toe brakes and two fixed on rollcabs. Integral locking
system locks all drawers with the turn of one key. Supplied with two keys. Supplied with 12mm PVC coated MDF worktop for use as a workbench
when not used with a topchest. Use with Model No. PTB141507 Topchest or as a standalone unit.
3. SPECIFICATION (W X D X H)
Model no. ............................................................ PTB141507
Overall size ...........................................1415 x 450 x 565mm
Medium drawer x3 .....................................695 x 385 x 58mm
Medium 1/2 drawer x2 ...............................615 x 385 x 58mm
Large drawer x1 ......................................695 x 385 x 135mm
X-large 1/2 drawer...................................615 x 385 x 210mm
4. ASSEMBLY
WARNING! These cabinets are heavy! Two persons are required
‰
to complete the assembly safely.
4.1. ROLL CAB HANDLE INSTALLATION
Position the handle over the holes in the roll cab, attach using the M6 x 12mm hex bolts and tighten securely (fig.1). Assembling the
handle first will make it easier to handle the roll cab.
4.2. CASTOR INSTALLATION
4.2.1. Lay the roll cab on its back carefully, protecting it with a soft mat placed on the floor.
4.2.2. Position the two rigid wheels in the centre of the rollcab.
4.2.3. Insert the M8 x 20mm hex bolts through the washers, then through the brackets and into the base of the roll cab, tightening securely.
4.2.4. Repeat with the two swivel castors at each outer end.
4.2.5. Stand the rollcab upright carefully.
4.3. ROLL CAB AND TOP CHEST CONNECTION
4.3.1. Remove the worktop from the rollcab.
4.3.2. Place the top chest onto the rollcab.
© Jack Sealey Limited
7 DRAWER 1415MM HEAVY-DUTY TOPCHEST
11 DRAWER 1430MM HEAVY-DUTY ROLLCAB
PTB141507/PTB143011
MODEL NO's:
Original Language Version
Model no .................................................................PTB143011
Overall size ............................................ 1430 x 460 x 1050mm
Full width large drawer x1 ....................... 1345 x 385 x 130mm
Medium drawer x3 ....................................... 695 x 385 x 58mm
Medium 1/2 drawer x3 ................................. 615 x 385 x 58mm
Large drawer x1 ........................................ 695 x 385 x 135mm
Large 1/2 drawer x1 .................................. 615 x 385 x 135mm
X-large drawer x1 ...................................... 695 x 385 x 210mm
X-large 1/2 drawer x1 ................................ 615 x 385 x 210mm
PTB141507, PTB143011 Issue:2 (2) 12/05/21