Advertisement
Resetting the Camera
If setup needs to be repeated, or to connect the camera to a different network, activate the Reset switch as seen at right.
• To reset the connection, press and hold the reset button until the LED on the camera starts blinking again.
• To join a new/different network:
On the app's Cameras screen, press
o
Press and hold the Reset switch to reset all settings to their factory defaults
o
Unplug the camera and then reconnect it.
o
Repeat the registration procedure.
o
During installation
Blue, blinking
Power on. Ready to start setup.
Blue, steady
Connected to the app. Ready to complete setup.
Purple, steady
QR code scan is complete. Restart the Wi-Fi connection process.
Green, blinking
Connecting to Wi-Fi network.
Red, steady
Setup timed out. Unplug the camera, plug it back in and restart setup process.
During operation
Green, blinking
Connecting to Wi-Fi network.
Green, steady
Connected to Wi-Fi and operating. Note: The camera is always ready to record but only originates live streaming video when the app
calls for a live stream.
Red, blinking
Not connected to Wi-Fi.
Low-light operation is indicated by four red LEDs arranged around the lens on the front of the camera.
IPCAM-WOC1 can be wall- or ceiling-mounted. The camera can be installed with cables running along the outside of a wall, or inside the wall.
For outdoor installations where cables are exposed to the weather, please protect the cable-ends with an enclosure such as a weatherproof
single-gang box, available at most hardware stores. In any installation, make sure the camera's antenna is firmly connected.
Checking Wi-Fi signal strength at the site using the app:
On the Cameras page, touch
•
the camera you're setting up
(on Android, touch )
Select Camera Information >
•
Signal Strength is displayed under
•
"IP Address"
60 – 100 Optimal
o
40 – 60
Marginal
o
00
– 40
Use of a range extender
o
strongly recommended
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may
cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient the receiving antenna until interference is reduced or eliminated.
•
Move the radio or television receiver away from the receiver/control.
•
Move the antenna leads away from any wire runs to the receiver/control.
•
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d'Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet
appareil ne doit pas causer d'interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
RF EXPOSURE STATEMENT:
The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
MISE EN GARDE EXPOSITION AUX FRÉQUENCES RADIO:
L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
DECLARACIÓN IFETEL
La operación de este equipo está sujeta a las siguientes dos condiciones
1.
Es posible que este equipo o dispositivo no cause interferencia perjudicial y
2.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada.
TRADEMARKS
Honeywell is a registered trademark of Honeywell International Inc.
For online support visit, https://mywebtech.honeywell.com/
For the latest warranty information, visit http://www.security.honeywell.com/hsc/resources/wa/
Ê800-23672EŠ
800-23672
9/17 Rev. A
and delete the camera from the link on its settings page.
LED STATUS INDICATOR
More about mounting at the installation site
for
BETA
Wall mount example
DECLARACIÓN ANATEL
Este equipamento opera emcarátersecundário, isto é, nãotemdireito a proteção
contra interferência prejudicial, mesmo de estações do mesmotipo, e
nãopodecausarinterferência a sistemas operando emcaráterprimário.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2017 Honeywell International Inc.
www.honeywell.com/security
Ceiling mount example
Advertisement
