Basic Operation; Bluetooth Operation - Sharp HT-SB100 User Manual

ū Connect the HDMI cable (not included) from unit's HDMI (ARC)
socket to the HDMI (ARC) socket on your ARC compliant TV. Then
press the remote control to select HDMI ARC.
TIPS:
• Your TV must support the HDMI-CEC and ARC function and this
must be set to "ON" or "ACTIVE" in the TV settings menu.
• The setting method of HDMI-CEC and ARC may differ depending
on the TV. For details about ARC function, please refer to your TV
manual.
• Only HDMI cables of version 1.4 or higher can support the ARC
function.
OPTICAL input
(Refer to 8 on page 2).
• Remove the protective cap of the OPTICAL socket, then connect an
OPTICAL cable (not included) to the TV's OPTICAL OUT socket and
the OPTICAL socket on the unit.
TIP:
While in HDMI ARC/OPTICAL mode, if there's no sound output from
the unit and the HDMI ARC/OPTICAL lights flashes quickly, you may
need to activate PCM signal output on your source device (eg. TV, DVD
or Blu-ray player).
AUX
(Refer to 9 on page 2).
A. Use a RCA to 3.5mm audio cable (not included) to connect the TV's
audio output sockets to the AUX socket on the unit.
B. Use a 3.5mm to 3.5mm audio cable (not included) to connect the
TV's or external audio device headphone socket to the AUX socket
on the unit.
TIP:
When you use the headphone output on the TV set, you will be able to
adjust the volume level directly using the TV remote control.
Connect to power
(Refer to 10 on page 2).
• Before connecting the AC power cord, ensure you have completed
all other connections.
• Risk of product damage! Ensure that the power supply voltage
corresponds to the voltage printed on the back or the underside
of the unit.
• Connect the power cable to the AC~ Socket of the unit and then
into a power socket.

Basic operation

Standby/ON
• When you first connect the unit to the power socket, the unit will be
in STANDBY mode. The indicator will light up red.
• Press on the remote control to switch the soundbar ON or OFF.
• Disconnect the plug from the power wall socket if you want to
switch the unit off completely.
ū The soundbar can also be controlled when connected via HDMI CEC.
ū If a TV or an external device (Only for AUX socket) is connected, the
unit will switch on automatically when the TV or the external device is
switched on.
ū When the unit has no input signal for over 15 minutes, it will
automatically switch to Standby mode.
Select modes
Press on the unit repeatedly or on the remote control to select the
desired mode.
Red: STANDBY
Green: AUX
Blue: Bluetooth
Yellow: OPTICAL
Cyan: HDMI ARC
Purple: USB
Adjust the volume
ū Press the +/– buttons on the unit or on the remote control to adjust
the volume.
ū If you wish to turn the sound off, press
the soundbar. Press again or press the +/– on the unit or on the
remote control to resume normal listening.
ū While adjusting the volume, the status indicator flashes quickly.
When maximum or minimum volume levels are achieved, the
flashing will stop.
Select equaliser (EQ) effect
During playback, press the EQ button on the remote control to select
between preset equalisers. Each time the EQ button is pressed the
soundbar will change between the EQ functions:
• Movie (for movies and films) - yellow light flashes for 2 seconds.
• Music (for all types of music) - green light flashes for 2 seconds.
• Voice (for listening to dialogue) - red light flashes for 2 seconds.
• Custom (for personal bass/treble settings) - white light flashes for
2 seconds.
Custom settings
• Press the EQ button to enter Custom settings or press either the
BASS or TRE button +/- buttons once, a white light will flash for 2
seconds.
• Use the BASS/TRE buttons on the remote control to increase (+)
or decrease (-) the EQ level. The selected EQ level is indicated by
the speed at which the LED indicator on the Soundbar flashes.
A flashing red LED indicates an increased level, a white LED (not
flashing) indicates the level is flat/0, a flashing green LED indicates
a decreased level.
LED colour EQ level
RED
White
Green
NOTE: New EQ changes are saved as default. You have 3 seconds
between each key press to make any changes before the EQ mode exits.
AUX/OPTICAL/HDMI ARC
1. Ensure that the unit is connected to the TV or audio device.
2. While in ON mode, press
remote control to select the desired mode.
3. Operate your audio device directly for playback features.
4. Press +/– button to adjust the volume to your desired level.
TIP:
While in HDMI ARC/OPTICAL mode, if there's no sound output from
the unit and the HDMI ARC/OPTICAL lights flashes quickly, you may
need to activate PCM signal output on your source device (eg. TV, DVD
or Blu-ray player).

Bluetooth operation

Pair Bluetooth-enabled devices
The first time you connect your Bluetooth device to this player, you
need to pair your device to this player.
on the remote control or
Speed LED flashing
+3 Fast
+2 Medium
+1 Slow
0 On
-1 Slow
-2 Medium
-3 Fast
on the unit repeatedly or on the
EN